Inovonics EchoStream EN1235D Handleiding

Inovonics Controller EchoStream EN1235D

Lees hieronder de 📖 handleiding in het Nederlandse voor Inovonics EchoStream EN1235D (2 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
© 2010 Inovonics - www.inovonics.com
EchoStream® EN1233S/D and EN1235S/D
Pendant Transmitter
Installation Instructions - 05596B
1 Overview
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics
Wireless technical services:
• E-mail: support@inovonics.com
• Phone: (800) 782-2709
1.2 Pendant Transmitter Components
Figure 1 Pendant Transmitter components
2 Installation and Startup
2.1 Install/Replace the Battery
1. Pry the housing apart at either end and pull the two halves
apart.
2. If replacing a battery, remove the old battery.
3. Install the new battery.
4. Press the Reset button to initialize the transmitter.
2.2 Select the Frequency Band
EchoStream products are able to use a range of radio frequencies,
and must be configured for your geographic area. To configure the
transmitter:
1. Pry the housing apart at either end and pull the two halves
apart.
2. Place a selection jumper on the appropriate frequency band
selection pins.
• Leave the jumper off the pins to set the frequency range to
902-928 MHz for North America.
• Place the jumper on the bottom pins, marked NZ, to set the
frequency range to 921-928 MHz for New Zealand.
• Place the jumper on the top two pins, marked AU, to set the
frequency range to 915-928 MHz for Australia.
3. ResetPress the button to complete configuration.
Caution: When pressing the Reset button, make sure you don’t
also touch the frequency band selection pins. Touching the
frequency band selection pins while pressing the Reset button can
inadvertently set the pendant to the wrong frequency band.
2.3 Register the Pendant Transmitter
The pendant transmitter must be registered with the system in order
to be monitored and supervised. When supervised, the pendant
transmitter will send a check-in message to the serial receiver or
network coordinator every three minutes.
Each pendant has a unique factory-programmed identification
number. Refer to the control panel’s installation instructions for
details on registering a transmitter.
1. When prompted by the receiver to reset transmitter, press the
Reset button.
2. Replace the cover.
Caution: The pendant should be tested after registration to ensure
operation. To test the pendant, activate each of the conditions and
ensure an appropriate response.
3 Operation
3.1 Using The EN1233 Pendant Chain
Always use the chain included with the ES1233. Substituting
stronger cords or chains may result in injury to the wearer.
3.2 Converting the Pendant Transmitter Belt Clip
If you’d like to convert the pendant transmitter belt clip to a belt loop,
secure the bottom of the belt clip to the housing with a coarse
thread screw.
Figure 2 Use a coarse thread screw to secure the belt clip
3.3 Operate the Pendant Transmitter
To activate single button transmitters, press the button for at least
one second. To activate double button transmitters, press both
buttons simultaneously. Alarm signals are transmitted multiple times
and are indicated by the blinking transmission LED. When the
buttons are released, the transmitter sends an alarm restoral
signal.To test a transmitter, activate the alarm by pressing the
button(s).
4 Specifications
Typical battery life: 3-5 years
Battery type (BAT608): Panasonic CR2 or equivalent
Operating environment: 0 to 60°C (32 to 140°F), noncondensing
A BReset button Frequency band selection pins
CBattery
B
AC
Printing Instructions
1. Print Duplex
2. Align and orient back page to match front
page.
3. Cut on dashed line
4. Fold cutsheet in half along the 8.5" axis.
© 2010 Inovonics - www.inovonics.com
Note: Specifications and data are subject to change without notice.
5 Warranty and Disclaimer
Note: Changes or modifications to this unit not expressly approved
by Inovonics Wireless Corporation may void the installer's authority
to operate the equipment as well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to
be free of defects in materials and workmanship under normal use
for a period of thirty-six (36) months from the date of manufacture.
Within the warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics will not be
responsible for dismantling and/or reinstallation charges. To
exercise the warranty, the User ("User", "Installer" or "Consumer")
must work directly through their authorized distributor who will be
given a Return Material Authorization ("RMA") number by
Inovonics. Details of shipment will be arranged directly through the
authorized distributor.
This warranty is void in cases of improper installation, misuse,
failure to follow installation and operating instructions, alteration,
accident or tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other
warranties, obligations or liabilities, whether written, oral, express,
or implied. There is no warranty by Inovonics that Inovonics product
will be merchantable or fit for any particular purpose, nor is there
any other warranty, expressed or implied, except as such is
expressly set forth herein. In no event shall Inovonics be liable for
an incidental, consequential, indirect, special, or exemplary
damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business,
nor any claim made by distributor's customers or any other person
or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this
warranty.
This warranty will apply only to Inovonics Products. Inovonics will
not be liable for any direct, incidental, or consequential damage or
loss whatsoever, caused by the malfunction of Product due to
products, accessories, or attachments of other manufacturers,
including batteries, used in conjunction with Inovonics Products.
Note: E-mail support@inovonics.com for a copy of the CE
Declaration of Conformity.

Product specificaties

Merk: Inovonics
Categorie: Controller
Model: EchoStream EN1235D

Heb je hulp nodig?

Als je hulp nodig hebt met Inovonics EchoStream EN1235D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Controller Inovonics

Inovonics

Inovonics EchoStream EN1235S Handleiding

19 Juni 2023
Inovonics

Inovonics EchoStream EN1235D Handleiding

10 Juni 2023
Inovonics

Inovonics EchoStream EN1223D Handleiding

31 Mei 2023
Inovonics

Inovonics EchoStream EN1233D Handleiding

22 Mei 2023
Inovonics

Inovonics EchoStream EN1233S Handleiding

20 Mei 2023
Inovonics

Inovonics EchoStream EN1223S Handleiding

17 Mei 2023

Handleiding Controller

Nieuwste handleidingen voor Controller

IVT

IVT SCDplus Handleiding

11 December 2024
IVT

IVT MPPTplus+ 20A Handleiding

10 December 2024
GVM

GVM YK22 Handleiding

10 December 2024
Alfatron

Alfatron ALF-IPCON-HDMI Handleiding

10 December 2024
Harvia

Harvia Xenio C260 Handleiding

8 December 2024
Hotone

Hotone Patch Kommander Handleiding

7 December 2024
Hotone

Hotone Ampero Control Handleiding

7 December 2024
IFM

IFM AC1317 Handleiding

5 December 2024
Speed-Link

Speed-Link Thunderstrike Handleiding

2 December 2024
COLBOR

COLBOR CTRL1 Handleiding

29 November 2024