HuddleCamHD HCM-1 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor HuddleCamHD HCM-1 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Step 2
Screw mount to pipe securely, engag-
ing a minimum of of pipe into 1/2”
mount (Fig 4). When aligned to desired
locaîžźon, îžźghten set screw (Fig 1, #2)
to 30 36 in lbs of torque (this is ap-- -
proximately when the set screw will
stop moving and the long arm of the
“long arm hex wrench” (Fig 1, #3) will
start to bend slightly).
What s Included’
QTY —Small Ceiling Mount BK/WH1
QTY — x 3/8" PPH and QTY — Machine Screw Flat Washer (Fig 1, #1)1 1/4"-20 2 1/4”
QTY — cup point set screw (Fig 1, #2)1 10/32 x 1/4”
QTY — long arm hex wrench (for set screw) (Fig 1, #3)1 3/32”
#2
#3
Fig 1
Rev 2.1
5/15/2020
HCM-1C
Small Base Camera
Ceiling Mount
Setup Guide
Mounîžźng Instrucîžźons
Step 1
Screw NPT pipe, or pipe nipple, to a properly 1”
installed mounng plate or pipe ange (Fig 2).
Tighten unîžźl pipe can no longer be îžźghtened with
a pipe wrench.
If using a plate or ange you must us a 1.5” 1.5” -
1” reducing bushing (Fig 3).
NOTE: Plate/ange, reducer bushing and NPT 1”
pipe or nipple are not included.
Fig 2 Fig 4
For more informaîžźon on HuddleCamHD
mounts and other products please visit:
hîž©ps://huddlecamhd.com/ Rev 2.1
5/15/2020
HuddleCamHD
HC- -WEBCAM 94
HC-GO
HC- -EPTZ XXX
HC3X-XX-G2
HC3XA-XX
HC3XW-XX-G2
HC10X USB2- -XX
HC10XA-XX
HC10X-XX-G3
HC20X-XX-G2
Step 4 / 4
Pass cabling through pipe or dress
to outside of pipe and connect for
a clean installaîžźon.
Mounîžźng Instrucîžźons Conîžźnued...
Mount Compaîžźbility
Step 3 / 4
Mount camera upright to top of mount
or invert to boîž©om of mount with includ-
ed 1/4 20 machine screw. (Fig 1, # 1) Uîžź--
lize (0,1,2) machine screw at wash-1/4”
ers as required. (Fig 1, #1) Note: 1/4”
machine screw at washers are to be
used depending upon depth of thread
insert in base of camera, in order to
achieve a snug t.
Other Cameras…
This mount has been
designed for use with most
small based cameras uîžźlizing
a 1/4 20” -mounng hole as
can be found on SONY,
Panasonic, Cisco, Polycom
and Vaddio cameras.
PTZOpîžźcs
PT 80- -WEBCAM
PTEPTZ ZCAM-XXX-
PTVL-XXX- ZCAM
PT12X-XXX-ZCAM
PT20X-XXX- ZCAM
PT12X-XXX XX- - G2
PT20X-XXX XX- - G2
PT30X-XXX XX- - G2


Product specificaties

Merk: HuddleCamHD
Categorie: Niet gecategoriseerd
Model: HCM-1

Heb je hulp nodig?

Als je hulp nodig hebt met HuddleCamHD HCM-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd HuddleCamHD

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd