Hotpoint-Ariston ON 837 I RFH Oven Handleiding

Hotpoint-Ariston OVENS ON 837 I RFH Oven

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint-Ariston ON 837 I RFH Oven (28 pagina's) in de categorie OVENS. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

Operating Instructions

Contents

Installation, 2-3

Positioning

Electrical connections

Description of the appliance, 4

Overall view

Control panel

Start-up and use, 5

Starting the oven

Data plate

The electronic cooking programmer, 6

Analogue Programmer, 7

Cooking modes, 8-10

Cooking modes

Practical cooking advice

Cooking advice table

Precautions and tips, 11

General safety

Disposal

Respecting and conserving the environment

Assistance

Maintenance and care, 12

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Sliding Rack Kit assembly

OVEN

English,1

MOS 837 J X RU/HA

MOS 838 J X RU/HA

MOT 857 RU/HA

MOT 857 C RU/HA

, 13

595 mm.

24 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

560 mm.

547 mm. min.

Installation

60 mm.

45 m

! Before placing your new appliance into operation

please read these operating instructions carefully.

They contain important information for safe use, for

installation and for care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

Positioning

! Keep packaging material out of the reach of

children. It can become a choking or suffocation

hazard.

see Precautions and tips

! The appliance must be installed by a qualified

person in compliance with the instructions provided.

Incorrect installation may cause harm to persons,

animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the

appliance functions properly.

• The panels adjacent to the oven must be made of

heat-resistant material.

• Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up

to 100°C.

• To install the oven under the counter (

see diagram

)

and in a kitchen unit, the cabinet must have the

following dimensions:

! The appliance must not come into contact with

electrical parts once it has been installed.

The consumption indications on the data plate have

been calculated for this type of installation.

Ventilation

To ensure good ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (

see diagrams

Centring and fastening

Position the 4 tabs on the side of the oven according

to the 4 holes of the outer frame. Adjust the tabs

according to the thickness of the cabinet side panel,

as shown below:

thickness of 20 mm: take off

the removable part of the tab

(

see diagram

)

thickness of 18 mm: use the

first groove, which has already

been set in the factory (

see

diagram

)

thickness of 16 mm: use the

second groove (

see diagram

)

Secure the appliance to the cabinet by opening the

oven door and putting 4 screws into the 4 holes of the

outer frame.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

Centring and fixing*

1. Position brackets “A”“A”

“A”“A”

“A” against oven support

“BB

B”.

2. Position tabs “C”“C”“C”“C”“C” against brackets “A” “A” “A” “A” “A”. If the

thickness of the cabinet side panel:

• is 16 mm thick: place the tab so that the

number 16 written on it is facing you;

• is 18 mm thick: place the tab so that the part

without any text is facing you;

• is 20 mm thick: do not fit the tab.

3. Fix the brackets and tabs onto the edge of the

cabinet side panel using screws “D”.“D”.

“D”.“D”.

“D”.

4. Fix the oven to the cabinet using the screws and

plastic washers “E” “E”

“E” “E” “E”.

Electrical connections

! Ovens equipped with a three-pole power supply

cable are designed to operate with alternating

current at the voltage and frequency indicated on

the data plate located on the appliance (

see below

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(

see diagram

2. Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3. Remove the wire

contact screws L-N-

, then fasten the wires

under the screw heads,

respecting the colour

code: Blue (N), Brown

(L) and Yellow-Green

Verde ( ).

Connecting the supply cable to the mains

Install a standardised plug corresponding to the

load indicated on the data plate (

see side

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum

contact opening of 3 mm installed between the

appliance and the mains, suitable for the load indicated

and complying with current electrical regulations (the

earthing wire must not be interrupted by the circuit-

breaker). The supply cable must not come into contact

with surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate (

see below

• The voltage must be in the range between the

values indicated on the data plate (

see below

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only (

see Assistance

! The manufacturer declines any liability should! The manufacturer declines any liability should

! The manufacturer declines any liability should

these safety measures not be observed.these safety measures not be observed.these safety measures not be observed.these safety measures not be observed.these safety measures not be observed.

* Only on certain models.