Hotpoint-Ariston 7OFH 837C (BK) RU/HA Oven Handleiding

Hotpoint-Ariston OVENS 7OFH 837C (BK) RU/HA Oven

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint-Ariston 7OFH 837C (BK) RU/HA Oven (28 pagina's) in de categorie OVENS. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
GB
Operating Instructions
Contents
Installation, 2-3
Positioning
Electrical connections
Description of the appliance, 4
Overall view
Control panel
Start-up and use, 5
Starting the oven
Using the cooking timer
Data plate
The electronic cooking programmer, 6
Analogue Programmer, 7
Cooking modes, 8-10
Cooking modes
Practical cooking advice
Cooking advice table
Precautions and tips, 11
General safety
Disposal
Respecting and conserving the environment
Assistance
Maintenance and care, 12
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Sliding Rack Kit assembly
OVEN
English,1
GB
7OFH 837 C RU /HA
7OFTR 850 RU /HA
7OF 937 C.1 RU/HA
7OF 937 C.1 IX RU/HA
7OFH 837 C IX RU/HA
7OFQ 837 C.1 /HA
7OFTR 851 RU/HA
7OFH 837 J C IX RU/HA
7OFH 83 J IX RU/HA
OT 857 CO RFH
OT 857 O RFH
ON 838 I RFH
ON 837 I RFH
OT 857 CA RFH
OT 857 A RFH
Русский, 13
RS
2
GB
595 mm.
595 mm.
24 mm.
545 mm.
5 mm.
567 mm.
23 mm.
575-585 mm.
45 mm.
560 mm.
547 mm. min.
Installation
560 mm.
45 m
m.
! Before placing your new appliance into operation
please read these operating instructions carefully.
They contain important information for safe use, for
installation and for care of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of
the appliance.
Positioning
! Keep packaging material out of the reach of
children. It can become a choking or suffocation
hazard. see Precautions and tips).
! The appliance must be installed by a qualified
person in compliance with the instructions provided.
Incorrect installation may cause harm to persons,
animals or may damage property.
Fitting the appliance
Use the appropriate cabinet to ensure that the
appliance functions properly.
The panels adjacent to the oven must be made of
heat-resistant material.
Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.
• To install the oven under the counter (see diagram)
and in a kitchen unit, the cabinet must have the
following dimensions:
! The appliance must not come into contact with
electrical parts once it has been installed.
The consumption indications on the data plate have
been calculated for this type of installation.
Ventilation
To ensure good ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (see diagrams).
Centring and fastening
Position the 4 tabs on the side of the oven according
to the 4 holes of the outer frame. Adjust the tabs
according to the thickness of the cabinet side panel,
as shown below:
thickness of 20 mm: take off
the removable part of the tab
( )see diagram
thickness of 18 mm: use the
first groove, which has already
been set in the factory (see
diagram)
thickness of 16 mm: use the
second groove (see diagram)
Secure the appliance to the cabinet by opening the
oven door and putting 4 screws into the 4 holes of the
outer frame.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
3
GB
Centring and fixing*
1. Position brackets “A” against oven support B“ ”.
2. Position tabs “C against brackets “A. If the
thickness of the cabinet side panel:
is 16 mm thick: place the tab so that the
number 16 written on it is facing you;
is 18 mm thick: place the tab so that the part
without any text is facing you;
is 20 mm thick: do not fit the tab.
3. Fix the brackets and tabs onto the edge of the
cabinet side panel using screws “D”.
4. Fix the oven to the cabinet using the screws and
plastic washers “E”.
Electrical connections
! Ovens equipped with a three-pole power supply
cable are designed to operate with alternating
current at the voltage and frequency indicated on
the data plate located on the appliance (see below).
Fitting the power supply cable
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(see diagram).
2. Install the power
supply cable by
loosening the cable
clamp screw and the
three wire contact
screws L-N- .
Connect the wires to
the corresponding
terminals: the Blue wire
to the terminal marked
(N), the Brown wire to
the terminal marked (L)
and the Yellow/Green
wire to the terminal marked (see diagram).
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the
load indicated on the data plate (see side).
The appliance must be directly connected to the mains
using an omnipolar circuit-breaker with a minimum
contact opening of 3 mm installed between the
appliance and the mains, suitable for the load indicated
and complying with current electrical regulations (the
earthing wire must not be interrupted by the circuit-
breaker). The supply cable must not come into contact
with surfaces with temperatures higher than 50°C.
! The installer must ensure that the correct electrical
connection has been made and that it is compliant
with safety regulations.
Before connecting to the power supply, make sure that:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the maximum power of
the appliance, which is indicated on the data
plate (see below).
The voltage must be in the range between the
values indicated on the data plate (see below).
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it.
Do not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only (see Assistance).
! The manufacturer declines any liability should
these safety measures not be observed.
* Only on certain models.
E
E
D A
B
D
D
16
16
16
16
C
C
C
N
L


Product specificaties

Merk: Hotpoint-Ariston
Categorie: OVENS
Model: 7OFH 837C (BK) RU/HA Oven

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint-Ariston 7OFH 837C (BK) RU/HA Oven stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding OVENS Hotpoint-Ariston

Handleiding OVENS

Nieuwste handleidingen voor OVENS