Honeywell TH6210U2001/U Handleiding

Honeywell Thermostaat TH6210U2001/U

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell TH6210U2001/U (44 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 114 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/44

Package Includes:

• T6 Pro Thermostat

• UWP™ Mounting System

• Decorative Cover Plate

• Screws and Anchors

• 2 AA Batteries

• Thermostat Literature

T6 Pro

Programmable

Thermostat

Installation Instructions

– +

TH6320U2008,

TH6220U2000,

TH6210U2001,

Read before installing

Optional Cover Plate installation

NOTE: If Optional Cover Plate is not

required, see “UWP Mounting System

installation” on next page.

Use the Optional Cover Plate when

you need to cover paint gap from old

thermostat.

There are different cover plates

depending on when the thermostat was

manufactured.

For the square cover plate:

1. Separate the Cover Plate from

Mounting Plate.

2. Mount the Mounting Plate on to the

wall using any of the 8 screw holes.

Insert and tighten mounting screws

supplied with Cover Plate Kit. Do not

overtighten. See Figure 2. Make sure

the Mounting Plate is level.

3. Attach the UWP by hanging it on the

top hook of the Mounting Plate and

then snapping the bottom of the UWP

in place. See Figure 3.

4. Snap the Cover Plate onto the

Mounting Plate. See Figure 4.

Use supplied

screws and

wall anchors

UWP Mounting System installation

Use 3x supplied

screws (#8 1-1/2

for red anchors and

#6 1-1/2 for yellow

anchors)

1. Before starting, turn the power off

at the breaker box or switch. Open

package to find the UWP. See Figure 1.

2. Position the UWP on wall. Level and

mark hole positions. See Figure 2.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into the wall using a hammer.

‒If your box contains red anchors,

drill 7/32” holes.

‒If your box contains yellow anchors,

drill 3/16” holes.

3. Pull the door open and insert the wires

through wiring hole of the UWP. See

Figure 3.

4. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 4.

1 2

For the rectangular cover plate:

1. Mount the Cover Plate on the wall using

any of the 6 screw holes. Insert and tighten

the mounting screws supplied with the

Cover Plate. Do not overtighten. See Figure

1. Make sure the Cover Plate is level. Attach

the UWP by hanging it on the top hook

of the Cover Plate and then snapping the

bottom of the UWP in place. See Figure 2.

2. If there are no existing wall anchors:

a. Position the Cover Plate on wall. Level

and mark hole positions. See Figure 1.

b. Drill holes at marked positions, and then

lightly tap supplied wall anchors into the

wall using a hammer.

• If your box contains red anchors, drill

7/32” (5.6 mm) holes.

• If your box contains yellow anchors,

drill 3/16” (4.8 mm) holes.

• Use 2x supplied screws (#8 1-1/2”

(38 mm) for red anchors and #6

1-1/2” (38 mm) for yellow anchors).

L/A

O/B

AUX

Power options

Wiring terminal designations

SInput for wired indoor

or outdoor sensors

(TH6320U and

TH6220U only)

L/A

- A

Heat Pump fault input

(Common (C) wire required

for LA/A)

SO/B Changeover valve

YCompressor contactor

(stage 1)

AUX -

Auxiliary heat

Heat (stage 2)

Y2 Compressor contactor

(stage 2) EEmergency Heat

GFan WHeat (stage 1)

24VAC common. For 2

transformer systems,

use common wire from

cooling transformer.

KUnused

Unused

R24VAC power from heating

transformer*

URc 24VAC power from cooling

transformer*

Note: Not all

terminals may be

used, depending

on the system

type that is being

wired. The most

commonly used

terminals are

shaded.

* Terminal can be jumped using Slider Tab. See “Setting Slider Tabs” above.

Set R Slider Tab.

• Use built-in jumper (R Slider Tab)

to differentiate between one or two

transformer systems.

• If there is only one R wire, and it is

connected to the , or terminal, set R, Rc RH

the slider to the up position (1 wire).

• If there is one wire connected to the R

terminal and one wire connected to the Rc

terminal, set the slider to the down position

(2 wires).

NOTE: Slider Tabs for U terminals should be

left in place for T6 Pro models.

Setting Slider Tabs

Insert R and C wires into

designated terminals

for primary AC power (C

terminal is optional if

batteries are installed,

but it is recommended).

Remove wires by

depressing the terminal

tabs.

Insert AA

batteries for

primary or

backup power.

R/Rc slider tab

UWP Mounting System

Product specificaties

Merk:	Honeywell
Categorie:	Thermostaat
Model:	TH6210U2001/U

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell TH6210U2001/U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Honeywell

Honeywell T4 Pro TH4110U2005 Handleiding

10 Juni 2024

Honeywell RTH9585WF Handleiding

27 Februari 2024

Honeywell BACnet TB3026B Handleiding

2 September 2023

Honeywell RTH221B1039/U1 Handleiding

9 Juli 2023

Honeywell RTH2410B1019/E1 Handleiding

7 Juli 2023

Honeywell RTH6580WF1001/U1 Handleiding

7 Juli 2023

Honeywell RTH111B1024/E1 Handleiding

6 Juli 2023

Honeywell RTH2300B1038/E1 Handleiding

6 Juli 2023

Honeywell Home THM6000R7001/U Handleiding

4 Juli 2023

Honeywell T4398B1003/U Handleiding

4 Juli 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024