Honeywell TE852W Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell TE852W (23 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/23
Honeywell
Long-Range Weather Forecaster with Wind Speed
(TE852W)
USER MANUAL
2
TABLE OF CONTENTS
INTRODUCTION 3
STANDARD PACKAGE CONTENTS 3
INSTALLATION 4
BEFORE YOU BEGIN 5
REMOTE TEMPERATURE & HUMIDITY SENSOR 6
WIND SPEED METER 8
MAIN UNIT 10
NAVIGATING THROUGH THE MODES 16
CUSTOMAZING YOUR WEATHER FORECASTER 18
BACKLIGHT 19
USING DIFFERENT DISPLAY WINDOWS 19
PRESSURE WINDOW 19
CLOCK WINDOW 23
SUNRISE/SUNSET WINDOW 29
TEMPERATURE AND HUMIDITY WINDOW 32
WIND WINDOW 35
MAINTANANCE 37
TROUBLESHOOTING 38
PRECAUTIONS 38
APPENDIX – CITY CODES 39
SPECIFICATIONS 41
FCC STATEMENT 43
DECLARATION OF CONFORMITY 44
STANDARD WARRANTY INFORMATION 45
3 3
INTRODUCTION
Thank you for selecting the Honeywell Long-Range Weather Forecaster with
Wind Speed. This device combines precise time keeping with monitoring and
displaying the wind speed information and temperature/humidity data from up
to five remote locations.
In this package you will find:
• One main unit (receiver) TE852W
• One three-channel remote temperature and humidity sensor
(transmitter) TS33C
• One Wind Speed Meter (transmitter) TS815
• Mounting Hardware with wrench tool for Wind Speed Meter
• One User Manual
Please keep this manual handy as you use your new item. It contains practical
step-by-step instructions, as well as technical specifications and precautions
you should know.
STANDARD PACKAGE CONTENTS
Picture Components
Main Unit (receiver)
Thermo Hygrometer Sensor (transmitter)
Wind Speed Meter (transmitter)
Consist of:
Meter Arm, Meter Base and Wind Cups
4 screws and small wrench tool Mounting hardware
4
INSTALLATION
The Honeywell Weather Forecaster with Wind Speed TE852W operates at
433MHz radio frequency, so no wire installation is required between the main
unit (receiver) and the remote weather sensors (transmitters).
The remote weather sensors include a temperature and humidity sensor and
wind speed sensor. All data measured by these remote sensors is transmitted
to the main unit wirelessly, with the operating range in the open area from 100
feet (30 meters) for wind speed meter up to 328 feet (100 meters) for
temperature and humidity sensor.
Remote wind speed meter must be placed outdoors to measure and transmit a
wind speed data.
Remote thermo-hygrometer(s) can be placed or indoors outdoors, depending
on the area where the temperature and humidity are intended to be
measured. If you intend measuring outdoor temperature and humidity, place
the remote sensor outdoors.
NOTE: It is critical to assemble and power up all remote weather sensors
BEFORE setting up the main unit.
NOTE: It is critical to power up and test communication between the weather
sensors and the main unit BEFORE permanently mounting them outside.
5 5
BEFORE YOU BEGIN
• We recommend using alkaline batteries for the remote weather
sensors and the main unit when temperatures are above 32°F (0°C).
We recommend using lithium batteries for the remote weather sensors
when temperatures are below 32°F (0°C)
• Avoid using rechargeable batteries. (Rechargeable batteries cannot
maintain correct power requirements)
• ALWAYS install batteries in the remote weather sensors before the
main unit
• Insert batteries before first use, matching the polarity in the battery
compartment
• Remove protective plastic screen from LCD display (if any)
• During an initial setup, place the remote weather sensors close to the
main unit
• After reception is established (all remote readings will appear on the
main unit’s display), position the remote sensors and the main unit
within the effective transmission range: 328 feet (100 meters) for
temperature/humidity sensors and 100 feet (30 meters) for wind speed
meter. Ideally they should be placed within the line of sight from the
main unit. See placement tips in the user manual for each remote
weather sensor.
• Transmission/reception range may be affected by trees, metal
structures and electronic appliances, by surrounding building materials
and the way how the receiver (main unit) and transmitters (remote
weather sensors) are positioned.
• The main unit must be placed indoors.
• Place the remote sensor so that it faces the main unit (receiver),
minimizing obstructions such as doors, walls and furniture.
6
NOTE: When the temperature falls below freezing, the batteries in the
outdoor remote sensor may have reduced voltage supply and a shorter
effective range. We recommend using lithium batteries at temperatures of
32°F (0°C) and below.
IMPORTANT: Make sure that remote weather sensors are easily accessible for
cleaning and maintenance.
We recommend cleaning the remote weather sensors periodically, as the dirt
and debris may affect sensors accuracy.
REMOTE TEMPERATURE & HUMIDITY SENSOR
FEATURES
• Remote data transmission to the main unit via 433 MHz frequency
• LCD displays temperature, humidity and channel
• Selection of the temperature display in Celsius or Fahrenheit
• Three (3) transmission channels selection
• Case can be wall mounted using built-in hanger
A. LED INDICATOR
• Flashes once when the remote sensor transmits a reading to the main
unit.
• Flashes twice when battery power is low.


Product specificaties

Merk: Honeywell
Categorie: Weerstation
Model: TE852W

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell TE852W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Weerstation Honeywell

Handleiding Weerstation

Nieuwste handleidingen voor Weerstation