Honeywell RTH9585WF1006/W Handleiding

Honeywell Thermostaat RTH9585WF1006/W

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell RTH9585WF1006/W (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 73 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

M34540

W-

O/B

W2-

Aux/E

Quick Start Guide

Smart Color Touchscreen

Programmable

Thermostat

RTH9585WF

Search for local rebates: HoneywellHome.com/Rebates

Install your thermostat.

Connect your home Wi-Fi network.

Welcome

Getting set up and ready is simple. Read before installing.

This thermostat works with common 24 volt

systems such as forced air, hydronic, heat

pump, oil, gas, and electric. It will not

work with millivolt systems, such as a gas

fireplace, or with 120/240 volt systems such

as baseboard electric heat.

1.1 Switch OFF power to your

heating/cooling system

1.1a Important! To protect your

equipment, switch OFF the

power to your heating/

cooling system at the

breaker box or the system

switch.

1.1b Confirm power is OFF.

Try to turn on heating/

cooling equipment by

changing temperature

on your old thermostat.

Your power is OFF if your

system does not turn ON.

Install your thermostat

Circuit

breaker

box

Heating/

cooling system

power switch

M33823A

Terminal

designation

If you have an older thermostat with a

sealed mercury tube, see warning page

for proper disposal instructions.

1.2 Remove old thermostat

faceplate and leave wires

connected

1.2a Take a picture of the wire

connections for later

reference.

1.2b If no wire is connected to a

terminal labeled C or no C

terminal exists on the old

thermostat, view the

Alternate Wiring videos at

wifithermostat.com/videos

Important! C wire is required

and is the power source for your

thermostat. Without a C

wire, your thermostat will

not power up.

1.3 Label wires

Do not label by wire color.

Use the supplied sticky tags to label

each wire as you disconnect it. Label

wires according to old thermostat

terminal designations, by wire not

color.

Note: If no tag matches a terminal

designation, write the appropriate

letter on a blank sticky tag.

Note: Wrap the wires around a pencil

to prevent them from falling back into

the wall.

1.4 Remove wallplate

Remove the old wallplate from

the wall after all wires are

labeled and disconnected.

Blank tags

Sticky tag

Terminal

designation

M31537

M31545

1.5 Mount wallplate for

thermostat

Mount your new wallplate using

screws and anchors included

with the thermostat.

If necessary:

• Drill 3/16-in holes for drywall

• Drill 7/32-in holes for plaster

Note: You may be able to use

your existing wall anchors. Hold

the wallplate up to the existing

anchors to check for alignment.

M34499

LEVEL

HERE

W-

O/ B

W2-

Aux/ E

Wallplate

1.6 Connect wires

Important! C wire is required and

is the power source. Without a C wire,

your thermostat will not power up.

See the C Wire Addendum

document for more information.

View the Alternate Wiring videos

at wifithermostat.com/videos

1.6a Starting with the C Wire, match

the sticky tag on the wire to the

terminal labels.

1.6b Straighten wire and gently slide

into terminal hole until it clicks

into place. (If you need to

remove a wire, use a pen tip to

press the terminal release and

then pull the wire out.)

Note: Refer to the wiring picture

you took in Step 1.2.

Tip: To make it easier to slide the

wire into place, use a pen tip to

hold down the terminal release.

Note: The wiring for your

application might be different

than the wiring shown below.

Labels don’t match or have

heat pump system?

See User Guide.

Labels don’t match or have

heat pump system?

See User Guide.

1.7 Attach thermostat

to wallplate

Align the thermostat with

wallplate and snap into

place.

Before you begin

Thermostat

Wallplate

LEVEL

HERE

M34498A

1.8 Switch heating/cooling

system ON

Important!

1.8a Verify that the C wire is

connected at the thermostat

and at the heating/cooling

system.

1.8b Make sure the heating/

cooling system door is

firmly secured.

1.8c Switch power back ON for

your heating/cooling system

at the breaker box or its

power switch.

Turn over

M31535

1.6c In the image on the right, check

the box next to each connection.

You will use this checklist in

Step 1.9.

1.6d Verify wire is firmly secured by

gently pulling on wire.

1.6e Repeat steps a–d for all other

wires.

1.6f Push any excess wire back into

the wall opening after all wires

are installed.

Note: LThe terminal on the lower

right is used only for Heat Pump

systems.

Note: If the old thermostat for

Heat Pump System has separate

wires on and , use a wire nut Aux E

to attach both wires to a separate

wire. Slide this third wire into the

W2-Aux/E terminal.

Terminal release

Circuit

breaker

box

Heating/

cooling system

power switch

M31535

View the installation video

at wifithermostat.com/

support

You will also need:

• Small screw driver

• Pen

• Your home WiFi

network password

You will need your

camera to take a

picture of your old wire

connections.

Note: You will need a

picture of your wire

connections to wire

the new thermostat.

Remove jumper loop ONLY if

you have both wires.R and Rc

Important!

Check the box for each wire

you connect. You will need

this information in Step 1.9.

W-O/B

W2-

Aux/E

EXAMPLE WIRING

Yours may look different

Resideo Inc., 1985 Douglas Drive North,

Golden Valley, MN 55422

33-00268—05 M.S. Rev. 04-22 | Printed in United States

This product is manufactured by Resideo Technologies, Inc. and its affiliates.

www.resideo.com

Electrical Ratings

Terminal Voltage (50/60Hz) Max. Current Rating

W-O/B 2030 Vac 1.0 A

W2 (Aux/E) 2030 Vac 1.0 A

Y Cooling 2030 Vac 1.0 A

Y2 Cooling 2030 Vac 1.0 A

G Fan 2030 Vac 0.5 A

33-00268-05

M38031A

HOME NFA

MODE

SETTINGS

SET TO

INDOOR

54% Humidity

FOLLOWING SCHEDULE

OUTDOOR

55% Humidity

Cool On

6:30 pm

M31570

If you get stuck...

At any point in the WiFi connection process, restart the thermostat by

removing the thermostat from the wallplate, wait for 5 seconds, and snap

it back into place. From the home screen, touch > SETTINGS Wi-Fi Setup >

Choose a Network. Continue with Step 2.1b.

Need more help?

Find additional information in the User Guide.

Getting Help

2.1 Connect the Wi-Fi network

After touching on the final screen Done

of the initial set up (Step 1.9g), the

thermostat displays an option to

connect to your WiFi network.

2.1a Touch

Yes

to connect the

thermostat to your WiFi

network. The screen displays the

message “Searching for wireless

networks. Please wait...” after

which it displays a list of all WiFi

networks it can find.

Note: If you cannot complete this step

now, touch . The thermostat I’ll do it later

will display the home screen. Complete

this process by selecting > MENU Wi-Fi

Setup. Continue with Step 2.1b.

2.1b Touch the name of the network

you want to use. The thermostat

displays a password page.

2.1c Using the keyboard, touch the

characters that spell out your home

network password.

2.1d Touch Done. The thermostat

displays “Connecting to your

network. Please wait...” then

shows a “Connection Successful”

screen.

Note: If your home network is not

shown on the list, touch

Rescan

2.1e Touch OK to display the

registration information screen.

Connect to your WiFi network

Yes

Your Network

Done

To view and set your thermostat remotely,

you must have a Total Connect Comfort

account. Follow the instructions below.

View the Thermostat

Registration video at

honeywellhome.com/wifi-thermostat

3.1 Open the Total Connect

Comfort web site

Go to www.mytotalconnectcomfort.com

3.2 Login or create an account

If you have an account,

click Login

– or –

click Create An Account.

3.2a Follow the instructions on the

screen.

3.2b Check your email for a response

from My Total Connect Comfort.

This may take several minutes.

Note: If you do not receive a response,

check your junk mailbox or use an

alternate e-mail address.

3.2c Follow activation instructions

in the email.

3.2d Log in.

3.3 Register your thermostat

After you are logged in to your Total

Connect Comfort account, register your

thermostat.

3.3a Follow the instructions on the

screen. After adding your

thermostat location you must enter

your thermostat’s unique identifiers:

• MAC ID

• MAC CRC

Note: The IDs are not case sensitive.

3.3b Notice that when the ermostat is th

successfully registered, the Total

Connect Comfort registration

screen will display a SUCCESS

message.

You can now control your thermostat

from anywhere through your laptop,

tablet, or smartphone.

GET IT ON

Total Connect Comfort free app is

available for Apple® iPhone®, iPad® and

iPod touch® devices at iTunes® or at

Google Play® for all Android™ devices.

This thermostat works with common 24 volt systems such as forced air,

hydronic, heat pump, oil, gas, and electric. It will not work with millivolt

systems, such as a gas fireplace, or with 120/240 volt systems such as

baseboard electric heat.

MERCURY NOTICE: Do not place your old thermostat in the trash if it

contains mercury in a sealed tube. Contact the Thermostat Recycling

Corporation at www.thermostat-recycle.org or 18002388192 for information

on how and where to properly and safely dispose of your old thermostat.

NOTICE: To avoid possible compressor damage, do not run air conditioner if

the outside temperature drops below 50°F (10°C).

Need help?

Visit honeywellhome.com/wifi-thermostat or call 18557335465 for assistance

before returning the thermostat to the store.

The operation of this equipment is subject to the following two conditions: (1) this equipment or device may not cause harmful interference, and (2) this equipment or