Honeywell CT50K1002/E1 Handleiding

Honeywell Thermostaat CT50K1002/E1

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell CT50K1002/E1 (16 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/16
Owner’s Manual
English: Page 1
Mode d’emploi
Français : Page 6
Manual de Uso
Español: Página 11
CT50 Series Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2019 Honeywell International Inc.
All rights reserved.
Read and save these instructions
M23786
MERCURY NOTICE
If your old thermostat contains
mercury, contact your local waste
management authority for proper
disposal instructions.
TURN OFF POWER at heating/cooling system (or fuse/circuit-breaker panel).
Remove cover and thermostat, but leave wallplate with wires attached.
Temperature Control Range
• 45°–95°F (7°–35°C)
• 35°–85°F (2°–29°C); select models; for garages or other outbuildings.
Is there a sealed tube containing mercury?
If so, see mercury notice below.
Leave wallplate in place.
Old thermostat Cover
Check package contents:
• Thermostat
• Wall anchors & screws (2 each)
• Wire labels
Before you begin, make sure you have:
• No. 2 Phillips & small pocket
screwdrivers
• Hammer
• Level (optional)
• Pencil
• Drill and bit (3/16” for drywall, 7/32” for
plaster)
Getting started
Remove your old thermostat
Vertical Mount:
CT50 (24 Vac heating systems)
CT51 (24 Vac heating and cooling systems)
CT53 (750 mV or 12Vdc heating systems)
Horizontal Mount:
CT54 (24 Vac heating systems)
CT55 (24 Vac heating and cooling systems)
69-2040EFS-04
CT50 Series • Owner's Manual
69-2040EFS—04 2
M23789
M23787
M23790
M23788
Wrap supplied labels securely around each wire. let wires fall into wall opening!Do not
IGNORE WIRE COLORS: Use only letter
designations to identify wire types.
For CT51/CT55: If your old
thermostat has 7 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
CT50/CT53/CT54
1. Pull wires
through base.
2. Level base if
desired.
3. Mark positions
of both screw
holes.
For CT50/CT53/CT54: If your old
thermostat has 3 or more wires
(not counting terminals C or C1),
you may have purchased the
wrong replacement thermostat.
Stop now and call 1-800-468-
1502 for advice.
Use a screwdriver to disconnect wires one by one. As you disconnect each wire, wrap it with
the label matching the letter on your old thermostat. (Adhesive labels are supplied in your
thermostat package.)
Remove the old wallplate only all wires are labeled. Be careful not to let loose wires fall after
into the wall opening.
Label wires and remove old wallplate
Mark mounting position
CT51/CT55
CT50/CT53/CT54 CT51/CT55
English: • Français : • Español: Page 1 Page 6 Página 11
3 69-2040EFS—04
Wiring CT50/CT53/CT54
• 2-wire heat-only system: Connect one
wire to terminal, one wire to terminal.R W
M23791
Wiring CT51/CT55
[1] If wires will be connected to both and R Rc
terminals, remove the metal jumper.
[2] Do not connect both and if you have a O B
heat pump. Connect only the wire. Wrap O B
wire with electrical tape and do not use.
[3] Do not use or . Wrap bare end of wire C X, B
with electrical tape.
1. Drill holes at pencil-marked
locations (3/16” holes for
drywall, 7/32” holes for
plaster).
2. Use hammer to tap anchors
into holes until flush with wall.
3. Pull wires through thermostat
base and insert screws.
Check level if desired, then
tighten screws.
Mount thermostat base
1. Match each labeled wire with same
letter on terminal.
2. Use a screwdriver to loosen
screw terminals, insert bare wires
beneath screws, then tighten
screws.
3. Push any excess wire back into the
wall opening.
Labels don't match?
If labels do not match letters on
thermostat, see table below.
Existing wires Connect to:
R 5 • • RH • Terminal “ V R” [1]
Rc Terminal “Rc” [1]
O Terminal “O” [2]
B Terminal “B” [2]
G F • Terminal “G”
W W1 H • • Terminal “W”
Y Y1 M• • Terminal “Y”
C X B • • Do not use [3]
CT51/CT55
CT50/CT53/CT54
Connect wires

Product specificaties

Merk: Honeywell
Categorie: Thermostaat
Model: CT50K1002/E1

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell CT50K1002/E1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermostaat Honeywell

Honeywell

Honeywell T4 Pro TH4110U2005 Handleiding

10 Juni 2024
Honeywell

Honeywell RTH9585WF Handleiding

27 Februari 2024
Honeywell

Honeywell BACnet TB3026B Handleiding

2 September 2023
Honeywell

Honeywell RTH221B1039/U1 Handleiding

9 Juli 2023
Honeywell

Honeywell RTH2410B1019/E1 Handleiding

7 Juli 2023
Honeywell

Honeywell RTH6580WF1001/U1 Handleiding

7 Juli 2023
Honeywell

Honeywell RTH111B1024/E1 Handleiding

6 Juli 2023
Honeywell

Honeywell RTH2300B1038/E1 Handleiding

6 Juli 2023
Honeywell

Honeywell Home THM6000R7001/U Handleiding

4 Juli 2023
Honeywell

Honeywell T4398B1003/U Handleiding

4 Juli 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components

Tru Components TCN4S-24R Handleiding

18 December 2024
Tru Components

Tru Components TK4S-14RC Handleiding

18 December 2024
Tru Components

Tru Components TX4S-14R Handleiding

17 December 2024
Warmup

Warmup 5iE Handleiding

16 December 2024
Warmup

Warmup +Kit Handleiding

16 December 2024
Nobo

Nobo Connect SWT-IZW Handleiding

15 December 2024
Nobo

Nobo Connect SWT-IZB Handleiding

11 December 2024
Hive

Hive Thermostat Handleiding

10 December 2024
GENERAL Life

GENERAL Life HT15S Handleiding

9 December 2024
GENERAL Life

GENERAL Life HT15 Handleiding

9 December 2024