Honeywell 6152 Handleiding

Honeywell Toegangscontrolesysteem 6152

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell 6152 (4 pagina's) in de categorie Toegangscontrolesysteem. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ADEMCO 6152 / / 6152V 6152ZN Remote Keypad –

User Guide

Addressable Fixed English & Voice Fixed English Keypads

= READY to Arm

= NOT READY to Arm

= System ARMED

= System NOT ARMED

Arming Keys

6152V: Message Indicators

6152-6152V-KEYPAD-LBLD-UG-07-19-13_1

= Recording Message

= No message

= Message Recorded

Programmable

Function Keys*

Sounder

6152V Microphone

See the keypad’s User Guide for details.

6152V Keys

The Function Keys can be be programmed

for special functions or panic alarm activations.

See the Function Keys section and check with

the system installer for more information.

Fixed Word Display

2-Digit Zone Identifier

The ‘21’ digits are used for speciﬁc

trouble indications. Refer to the

control panel instructions for details.

ALARM

FIRE

AWAY

BYPASS

STAY

CHECK

INSTANT CANCELED

NO NIGHT AC

NOT READY

CHIME BAT

TESTPHONE

6152V VOICE CONTROL KEYS

KEY FUNCTION DESCRIPTION

VOLUME ADJUST

Refer to the 6152V Keypad Voice

Features section for details using these

keys.

PLAY/STOP RECORD

VOICE KEY

FUNCTION/RECORD

SETTINGS KEY

The Settings key provides an easy method to test the keypad display.

To enter Display Test mode, press and hold the key for 2 seconds.

SINGLE BUTTON ARMING

If desired, the Arming Keys can be set for Single Button Arming by following

prompts to store a valid user code in the keypad. (See the system User Guide

for details on programming user codes.)

When Single Button Arming is disabled, a valid user code is required to arm the

system with the Arming keys

- 2 -

Enabling Single Button Arming

1. Press and hold down the and keys at the same time for 3

seconds. The screen displays the keypad’s address.

2. Press to move to the User Code entry screen (the screen flashes

“u4”, “- -” and “- -.”)

3. Enter a valid four digit user code between 0000 – 9999

and press to

save and exit.

Recommended: Set a dedicated user code for this feature.

The user code must be entered for each keypad in the system where Single

Button Arming is desired.

Disabling Single Button Arming

1. Press and hold down the and keys at the same time for 3

seconds. The screen displays the keypad’s address.

2. Press to move to the User Code entry screen (the screen flashes

“u4”, “- -” and “- -.”)

3. Enter and then press to exit.

FUNCTION KEYS

The Function keys may be programmed by the installer

for special functions or alarm activations. Key pairs

may also be programmed for alarm activations.

To activate the Function keys, press and hold the key

for at least 2 seconds; key pairs are activated

immediately.

Check with the system installer for more information.

COMMERCIAL STAY MODES

For commercial controls, if Stay Mode 2 is programmed, refer to the control’s

manuals and the table below for Stay mode arming.

Commercial Systems Stay Modes

+ 1 = Stay Mode 1

+ 2 = Stay Mode 2

= Stay Mode 3 (both Stay 1 and Stay 2 modes)

Note: Not intended for use with the VISTA-128/250 Series.

6152V KEYPAD VOICE FEATURES

Message Center

The keypads feature a voice message center that lets you record and playback

one message.

• The message can be up to 2.5-minutes long

• The message remains in the keypad’s memory until a new message is

recorded.

• The volume control of the message is adjustable.

A or and

B or and

C or and

- 3 -

To record a message: Press + + keys. The MESSAGE

ICON ( ) will light, indicating recording is in progress.

Note: A message cannot be recorded during the Exit Delay period.

To end recording: Press key, the keypad will ‘ding’ twice to indicate

recording is ended. The MESSAGE ICON will flash indicating a

message is waiting to be played.

To play a message: Press +

. The recorded message

plays and the MESSAGE ICON turns off. The recorded message will

remain in memory until a new message is recorded.

To adjust the volume:

Press

+ +

to adjust the volume

one level. Volume levels are Low, Off, On, High and Medium. With

each level adjustment, the keypad announces “CHECK” (at Low,

Medium and High volumes), “ON” or “OFF” to verify the current setting.

Note: Adjusting the message volume also adjusts status volume. The volume

cannot be adjusted while playing a message.

Voice Mode

When Voice mode is enabled, the keypad announces basic system arming status

upon arming or disarming (e.g., “Disarmed, Ready to Arm,” “Armed Away”).

To enable the Voice mode: Adjust the keypad volume to “On” or “Check” (at the

desired volume).

To disable the Voice mode: Adjust the keypad volume to “Off.”

Voice Chime

Each keypad can be set to announce faulted (opened) entry/exit or perimeter

zones when the control panel’s Chime mode is on.

To enable the Voice Chime mode: Adjust the keypad volume to “On” or

“Check” (at the desired volume) and turn on the keypad Chime mode

(Code + ).

When enabled, Voice Chime provides a voice status annunciation,

chime and display when any entry/exit or perimeter zone is faulted.

When the Voice mode is disabled but Chime mode is enabled, the

sounder will still provide Chime annunciations when zones are faulted.

Voice Status

The keypad can be set to announce current system status and display any

system and/or zone faults (if they exist).

To enable Voice Status: make sure Voice Chime mode is on, then:

• To Announce Status:

Press

key once.

The respective system status is announced (e.g., “Disarmed, Ready to

Arm” or “Disarmed, Not Ready to Arm”).

Note: Status cannot be announced during the Exit Delay period.

Product specificaties

Merk:	Honeywell
Categorie:	Toegangscontrolesysteem
Model:	6152
Soort bediening:	Knoppen
Kleur van het product:	Wit
Breedte:	176 mm
Diepte:	25.9 mm
Hoogte:	123.9 mm
Gebruikershandleiding:	Ja
Connectiviteitstechnologie:	Bedraad
Certificering:	UL, ULC, CAN/ULC-S545, ANSI/SIA, CE
Smartphone ondersteuning op afstand:	Nee
Gebruiksvriendelijk:	Ja
Stroomverbruik:	70 mA
Maximum aantal deuren:	1 deur(en)
Gemakkelijk te installeren:	Ja
Aantal bewegingssensoren:	0 stuk(s)
Stroom in standby:	40 mA
Alarm-bedieningspaneel:	Ja
Aantal deur-/raamsensoren:	0 stuk(s)