Holosun Paralow HS403B Handleiding

Holosun Niet gecategoriseerd Paralow HS403B

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Holosun Paralow HS403B (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
Fig 2-1
Features
Important notices
Battery
Installation
Fig1 PARALOW HS403B Red Dot Sight
www.holosun.com
HS403B
PARALOW Thank you for purchasing the PARALOW HS403B Red Dot
sight,Please read the User's Manual carefully.
1. The HS403B projects its aiming dot in
a way that prevents visibility when viewed from the front
beyond several meters.
2. The user can gain
rapid target acquisition and situational awareness while aiming
with both eyes open.
3. Only a few micro-a mperes of current
are required for sight operation. Sight runs on one battery for
up to 30,000 hours.
Concealed aiming:
Full field of view for target acquisition:
Low power consumption:
4. The sensitive motion sensor will turn the
power on with any motion detec๎†บon when in sleep mode.
5. arallax 1MOA
Motion power on:
Parallax free optical system: P is .
โ‰คยฑ
6. The sight will be automatically entered into
sleep mode motion less for 8 hours.
7. There are 12 settings(10 Daylight+2NV)
for the reticle so as to match the ambient lighting conditions.
8. The sight will remember the last saved
brightness setting when powered on and off.
9 The top mounted buttons allow
Sleep time delay:
Brightness adjustment:
Memory function:
.
Two top mounted buttons:
for easy operation without obstructing th e user's vision.
10. IP67 Waterproof:
1. Ensure that the firearm is completely unloaded and safe
before device installation or installing/replacing the
ba๎‡„ery.
2. Please keep the packaging should you need to make a
warranty claim.
1.The operating voltage for this device is DC3V using one high
quality CR2032 Lithium battery.
2.The ba๎‡„ery life is rated up to 50,000 hours at a mid-brightness
se๎‡„ing.
3.Ba๎‡„ery Replacement:
Please follow the steps below for battery replacement
1. The included mount is
compatible with Picatinny Rails.
2. First insert the appropriate Torx wrench(included) into the
crossbolt head, then rotate to loosen cross bolt then
a๎‡„ach the sight into a suitable position,
and finally tighten the clamp screw to 15 IN/LBS using
non-permanent thread locker. (Fig3)
Bri ghtness Decrease Bri ghtness Increase
Protective Cap
Objective Lens
Eyepiece Lens T10 Torx Crossbolt
Model
Fig 3
Clamp
screw headCross bolt
2) Ba๎‡„ery installation(Fig2-2):
a) Insert the ba๎‡„ery into the battery tray 2032 with
oriented with the POSITIVE SIDE DOWN.
b) Insert and press the tray into the battery compartment.
c)
Fasten screw 1,2.
Caution:
The loss or damage of seal ring will cause water to leak into
the compartment and may damage electronic circuits and
the device.
when battery runs out or for other condi๎†บons that require
the ba๎‡„ery to be changed :
1) Removing the battery (Fig 2-1):
a)Loosen screws 1,2.
b)Insert coin or similar object in the battery tray slot, pry
out the battery tray, and remove the discharged ba๎‡„ery
by li๎…ตing it up. A tool is provided for this purpose.
Fig 2-2
Slot
Screw 1
Screw 2
Screw 2
Screw 1
Battery
cabin
Battery
Seal ring
Sight operation
The operation panel is on the top of sight.(see Fig4)
Zero setting
Maintenance and care
Limited warranty
3
Fig 4
Brightness Decrease
Brightness Increase
PARALOW HS403B
Red Dot sight
1.On top of sight is the elevation adjusting turret, windage
adjusting turret is on the right side (see Fig5). The sight has
been factory adjusted for approximate zero.
2.The built in screw driver tool on the protective cap can be
used for zeroing alignment (see Fig5).See label inside cap.
3.First open the protective lid (see Fig1), position slot type
screwdriver on the slotted screw, then rotate the screw to
right or left for adjustment. Each left or right click is for one
adjustment, equivalent to 0.5M0A value.
4.Adjust the Elevation turret counterclockwise to move the
point of impact UP. Adjust the Windage turret counter-
clockwise to move the point of impact to the RIGHT. Turning
either turret clockwise moves the point of impact in the
opposite direction.
5.Caution:
Don't try to over rotate a turret, if you feel the turret can
Holosun Technologies Inc.
www.holosun.com
Phone: 909-594-2888
Email: @holosun.com
V2 2
warranty
1.Operation
1)Switch on: Press and release either brightness button
(โ€+โ€orโ€-โ€) to turn on the sight.
2) Brightness adjustment: There are 12 brightness settings.
The default brightness is the 7th level. Press the โ€œ+โ€orโ€-โ€
button until the red dot has a sufficient intensity to contrast
against the target. One changes
brightness
3)Power o๎…—: Press theโ€+โ€andโ€-โ€buttons simultaneously
turn the power and motion sensor off.
The sight will remember the last saved brightness
setting when powered on and off.
momentary press
by one step.
to
Note:
2.Motion sensor
1)Motion sensor is always enabled when the sight is on or in
sleep mode.
2)The sight will instantaneously wake up and turn on with any
motion detection to last saved setting.
1) Please note that your red dot will automatically
3. Sleep ime elayT r D
by default
a enter into sleep mode fter 8 hours of no movement.
2)The sleep time delay c be adjusted from 0 to 12 hours.
3)Sleep time delay
a)Press the โ€œ+โ€button for 3 seconds to enter time adjustment
mode. The red dot will blink .The number of blinks represents
the current time delay. One blink represents one hour of time
delay 8 blinks 8 hours
b)Press the โ€œ+โ€orโ€-โ€button to set the time. Pressingโ€+โ€ orโ€-โ€
one or more times will increase or decrease the time by one
hour for each press. The LED will blink once to confirm each
button press. If the sleep time delay is set toโ€0โ€
the feature is disabled
c) ress the โ€œ+โ€button for 3 seconds to confirm the new
setting and exit the time adjustment mode.
an
r
. For example, equals .
r blinks
. 5 rapid blinks confirms this setting.
P
not be rotated, this indicates you have reached the
adjustment limit, otherwise the device may be damaged.
If the required adjusting range is beyond the limits, consider
adding an extra spacer between the device and mounting rail
to allow for additional adjustment.
This device is a precision instrument that deserves
reasonably cautious care. The following tips are provided to
ensure long lasting use of the sight.
The optical system, including the objective lens and
eyepiece lens are multi-coated optical glass. When cleaning
the lenses, blow away the dust on surface , wet the lens
with lens cleaner or clean water, wiping the fingerprint or
other oi stain with lens tissue, soft co๎‡‡on or microfiber cloth.
No special maintenance is needed for the housing surface.
Avoid touching the glass surface with dry cloth or tissue paper.
Do not use organic solvents such as alcohol or acetone. Do not
try to dismantle the device as the internal parts are specially
cleaned and sealed and with an anti-fog treatment. Any such
attempt will void the warranty.
If repair is needed, you can call our customer service center,
visit our website, or send an email to us.
We provide a limited lifetime warranty from the date of
purchase on parts and workmanship to the original purchaser.
At our sole discretion, we will repair or replace product found
to be defective under normal use and service without charge,
excluding any delivery costs, which will be born by purchaser.
We will not be liable for incidental, consequential, or
special damages arising out of or in any connection with the
use or performance of this product. This warranty is void if
the product has been misused, modified, neglected, or
disassembled prior to its return.
Please refer to http://www.holosun.com for current and
complete warranty information and other conditions.
SUMMARY

Product specificaties

Merk: Holosun
Categorie: Niet gecategoriseerd
Model: Paralow HS403B

Heb je hulp nodig?

Als je hulp nodig hebt met Holosun Paralow HS403B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Holosun

Holosun

Holosun Paralow HS403B Handleiding

21 November 2024
Holosun

Holosun AEMS-CORE-120101 Handleiding

30 Juli 2024
Holosun

Holosun HS507C X2 Handleiding

30 Juli 2024
Holosun

Holosun DRS-NV Handleiding

23 Juni 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Lucide

Lucide Saar 03423/48/30 Handleiding

21 November 2024
Lucide

Lucide Bryton 13528/01/30 Handleiding

21 November 2024
Lucide

Lucide Swits 22504/03/31 Handleiding

21 November 2024
Lucide

Lucide Mesh 30773/01/30 Handleiding

21 November 2024
Lucide

Lucide Pia 45280/03/30 Handleiding

21 November 2024
Lucide

Lucide Pia 45580/01/30 Handleiding

21 November 2024
Lucide

Lucide Jur 72405/57/30 Handleiding

21 November 2024
Lucide

Lucide Lorenz 74403/06/97 Handleiding

21 November 2024
Deaf Bonce

Deaf Bonce Machete MLA-500.1XS Handleiding

20 November 2024
Deaf Bonce

Deaf Bonce Machete MLA-80.4XS Handleiding

20 November 2024