Hoffman APCABVA Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Hoffman APCABVA (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
OPERATOR ADAPTER APCABVA
Installation Instructions for Allen-Bradley Bulletin 1494V (Variable Depth)
1494C and 140U Cable Controlled
For oor-mounted enclosures with
disconnect on the right ange
For one- through ve-door free-stand enclosures
with the disconnect on the right ange
For oor-mounted enclosures with
disconnect on the centerpost
© 2011 Pentair Technical Products PH 763 422 2211 ‱ hoffmanonline.com 87400097Rev. E P/N 87400038
The functions, ts and clearances of the installation described hereon are calculated from information supplied by the manufacturers
of the equipment to be installed. Be certain to check the function, ts and clearances of all equipment both before and after installation
to assure that it operates properly and safely and meets all applicable codes, standards and regulations.
In the event the completed installation does not function properly or fails to meet any such codes, standards or regulations, do not
attempt to make alterations or operate the equipment. Report such facts immediately to:
Customer Service Department
Pentair Technical Products
2100 Homan Way
Anoka, MN 55303-1745
(763) 422-2211
homanonline.com
PARTS LIST
Operator Adapter, Catalog Number APCABVA, for Allen-Bradley Bulletin 1494V, 1494C
and 140U Disconnects
Item No. Part Name Part Number Quantity
1 Slide Arm, Flat 26250001 1
2 Shoulder Collar, 5/8 Diameter 26419001 1
3 Screw, 1/4-20x7/8 Hex Head 99401030 1
4 Lockwasher, 1/4 Spring 99401318 1
5 Washer, Flat 22101003 2
6 Lockwasher, 1/4 Internal Teeth 99401300 2
7 Nut, Hex, 1/4-20 99401406 2
8 Door Catch 23101002 1
9 Screw, #10-32x3/8 Pan Head 99401007 2
10 Lockwasher, #10 Internal Teeth 99401307 2
11 Label (Ectra) 26147001 1
12 Installation Instructions 87400038 1
© 2011 Pentair Technical Products PH 763 422 2211 ‱ hoffmanonline.com 87400097- 2 -
INTRODUCTION
This installation instruction is for the Allen−Bradley Small Handle.
Bulletin 1494V (variable depth), 1494C and 140U (cable control) mechanisms.
These mechanisms are for disconnect switches and circuit breakers mounted in Hoffman two-door, oor−mounted enclosures
with cutout on right-hand ange or centerpost and one- through ve-door, free−stand enclosures with the disconnect on the right
ange.
ALLEN-BRADLEY SMALL HANDLE INSTALLATION STEPS
See Figure 1 for 1494V or Figure 2 for 1494C and 140U Mounting.
Step 1: Install Allen-Bradley Small Operating Handle 1494F-S1 (Stainless Steel), 1494F-P1 (Non-metallic) or 1494F-M1 (Metal).
(1494V) Assemble the Allen−Bradley small operating handle and Allen−Bradley spring bracket to the enclosure ange. Omit cap
screw and lockwasher which t into bottom hole of Allen−Bradley operating handle.
(140U) Assemble the Allen−Bradley small operating handle and Allen−Bradley 140U H, J, K, M, OR N operating mechanism to
enclosure ange. Omit cap screw and lockwasher which t into bottom hole of Allen−Bradley operating handle.
(1494C) Assemble the Allen−Bradley small operating handle and Allen−Bradley 1494C CM and CMX operating mechanism to
enclosure ange. Omit cap screw and lockwasher which t into bottom hole of Allen−Bradley operating handle.
Step 2: Install Slide Arm.
Note: When mounting to centerpost, cut 2.50 inches off bottom of slide arm (item 1). Bottom of slide arm has three rectangular
slots.
(A) For 1494V install the slide arm (item 1) through the hole in bottom of Allen−Bradley spring bracket and over the defeater part
of the Allen−Bradley operating handle as shown.
(A) For the 1494C and 140U install the slide arm (item 1) over the defeater part of the Allen−Bradley operating handle as shown.
(B) Note that the notch in the slide arm (item 1) is positioned toward the door opening. Place the smaller diameter end of the
shoulder collar (item 2) through the oval slot in the slide arm (item 1). Install long cap screw (item 3) with lockwasher (item 4)
through shoulder collar into the bottom mounting hole of the Allen−Bradley operating handle and tighten. The slide arm (item 1)
should move up and down smoothly. Install Allen−Bradley defeater bracket per Allen−Bradley instructions.
Step 3: Attach the bottom of the slide arm (item 1) to the offset arm of the operator release mechanism. Use two at washers
(item 5), two lockwashers (item 6), and two hex nuts (item 7). Do not tighten until parts are adjusted (see Step 4B).
Step 4: The operator release mechanism is adjustable in two places.
(A) Check the adjustment of the factory-installed roller bracket. The door latch should hit against the latch portion of the roller
bracket when the door is closed and latched. Adjust up or down if necessary. The mechanism will then provide the necessary up−
down motion required to operate the safety lock release in the Allen−Bradley operating handle.
(B) Adjust the length of the slide arm assembly with proper adjustment of the slide arm. The safety lock (in the Allen−Bradley
operating handle) should release just before the master door is fully latched. Lengthen slide arm if safety lock releases too soon.
Shorten slide arm if safety lock releases too late. Tighten all hardware.
Step 5: Attach the door catch (item 8) provided by Hoffman to the tapped spacer on the door using the bottom set of mounting
holes. Use two screws (item 9) and two lockwashers (item 10). The door catch prevents the door from being opened when the
Allen−Bradley operating handle is in the “ON” position. The door catch may be adjusted up or down to hook properly on the
defeater bracket. The door catch (item 8) must be positioned so it just clears the top of the defeater bracket when the Allen−
Bradley operating handle is in extreme “OFF” position (handle pushed down against the handle housing surface).
© 2011 Pentair Technical Products PH 763 422 2211 ‱ hoffmanonline.com87400097 - 3 -


Product specificaties

Merk: Hoffman
Categorie: Niet gecategoriseerd
Model: APCABVA
Kleur van het product: Aluminium
Gewicht: 626 g
Soort: Rekframe
Materiaal behuizing: Staal
Montage gereedschap: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Hoffman APCABVA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Hoffman

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd