Hitachi VMPL2B Handleiding

Hitachi Niet gecategoriseerd VMPL2B

Lees hieronder de 📖 handleiding in het Nederlandse voor Hitachi VMPL2B (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 152 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113

800.359.5520 www.sanus.com 8.17.05

Step 3: Mounting the Wall Plate: Wood Stud, Brick, Solid Concrete, and Concrete Block

mounting options are provided.

Warning: DO NOT OVERTIGHTEN THE LAG BOLTS! Tighten Lag Bolts (u) only

until the Lag Bolt Washer (v) is pulled rmly against the Wall Plate (a)

Wood Stud mounting:

The Wall Plate (a) Use a high must be mounted to two wood studs at least 12" apart.

quality stud sensor to locate two adjacent studs. It is a good idea to verify where the studs

are located with an awl or thin nail shown in Diagram 3a. Pre-drill a 2.5" deep hole at the

desired height in each stud using a 3/16" drill bit. Make sure these holes are in the center

area of the studs and level with each other. Use the Wall Plate as a template to mark the

location of the second hole in each stud. Drill 2.5" deep holes using the 3/16" drill bit in the

marked locations. Attach the Wall Plate to the wall using the four 1/4 x 2.5” Lag Bolts (u)

and four Lag Bolt Washers (v). Make sure the Wall Plate is oriented so the at surface in the

center of the plate is against the wall and that a set of Lag Bolts is on each side of the two

large holes in the center as shown in Diagram 3b.

Brick, Solid Concrete and Concrete Block mounting:

Use the Wall Plate (a) as a template to mark 6 hole locations on the wall. The outer holes

must fall to left and right of the two large holes in the middle of the plate. Three in the top

row of slots and three more in the bottom row. Make sure these holes are level and there is

at least 6" between any two holes. Pre-Drill these holes with a 1/2" masonry bit to at least

2.5" in depth. Insert a Concrete Anchor (w) into each of these holes. Make sure the anchor

is seated completely ush with the concrete surface even if there is a layer of drywall or

other material in front. Attach the Wall Plate to the wall using 6 Lag Bolts (u) and 6 Lag

Bolt Washers (v).

Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113

800.359.5520 www.sanus.com 8.17.05

Step 4: Choose mounting position:

You can mount your television in either of two positions:

at or at a 5 degree downward tilt. To mount the television

at to the wall use only the Monitor Brackets (c). To mount

the television in the 5 degree tilt position you must rst add

two Gussets (d) to each Monitor Bracket with two Carriage

Bolts (x) and two Gusset Nuts (y) as shown in Diagram 4.

Diagram 4 Detailed View

x d d y

Step 5: Hang the TV onto the Wall Plate:

First hook the Monitor Brackets (c) over the top of the Wall Plate (a), then let the bottom of the Monitor Brackets rotate in under the

bottom of the Wall Plate. This process is shown with the at mount option in Diagram 5a, and with the 5 degree tilt option in Diagram

5b. Once the TV is in place, insert the Safety Bar (b) into the slots in the bottom of the Monitor Brackets so that it sits behind the bottom

tab on the Wall Plate as shown in Diagram 5c. The bend at the end of the Safety Bar should face toward the wall. Once the bar passes

out the other side of the Wall Plate a padlock can be added to the hole in the Safety Bar for additional security.

Diagram 5a Diagram 5b Diagram 5c

a a

slot for safety bar b

wall wall c

Assembly Instructions for VMPL2 Flat Panel Wall Mount

Thank you for choosing a Sanus Systems Vision Mount Wall Mount. This product is designed to mount at panel televisions weighing up to 175 lb. to

a vertical wall. It allows you to mount your television at against the wall or at a xed 5 degree tilt.

Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualied contractor or

contact Sanus at 800.359.5520 or www.sanus.com. We can quickly assist you with installation questions and missing or damaged parts. Replacement

parts for Sanus products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure there are no missing or

defective parts. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is

not explicitly specied by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or

incorrect use.

Note: The supplied wall mounting hardware is not for steel stud walls or old cinder block walls. If you are uncertain about the nature of your wall,

consult an installation contractor. Sanus makes every eort to assure all necessary television mounting hardware is included. If the hardware you need

is not included please consult your local hardware store or call Sanus Systems.

Required Tools: 3/16 drill bit, 1/2” Masonry Bit for brick concrete or concrete block installations, wrench or socket set, Phillips screw driver.

Supplied Parts:

(1) Wall Plate - a (1) Safety Bar - b (2) Monitor Bracket - c (4) Gusset - d

(4) M4 x 12 Bolt - e (4) M5 x 12 Bolt - f (4) M6 x 12 Bolt - g (4) M8 x 16 Bolt - h

(4) M4 x 30 Bolt - i (4) M5 x 30 Bolt - j (4) M6 x 35 Bolt - k (4) M8 x 40 Bolt - l

(4) M4 Lock Washer - m (4) M5 Lock Washer - n (4) M6 Lock Washer - o (4) M8 Lock Washer - p

(4) M4/M5 Spacer - q (4) M6/M8 Spacer - r (8) M4/M5 Washer - s (4) M6/M8 Washer - t

(6) Lag Bolt - u (6) Lag Bolt Washer - v (6) Concrete Anchor - w

(4) Carriage Bolt - x (4) Gusset Nut - y

Diagram 3a

Diagram 3b

v a

Step 1: Mounting Monitor Brackets to a television with a at back

First, determine the diameter of the Bolt (e,f,g,h) your TV requires by hand threading them into the threaded insert on the back of the TV.

If you encounter any resistance stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below.

You will thread the Bolt through the appropriate Lock Washer (m,n,o,p), a Washer (s,t), the Monitor Bracket (c), and nally into the TV.

Make sure the Monitor Brackets are vertically centered and level with each other.

M4 Diameter Bolt M6 Diameter Bolt

e g

m o

s t

c c

Diagram 1

M5 Diameter Bolt M8 Diameter Bolt

f h

n p

s t

c c

Step 2: Mounting the Monitor Brackets to a television with a curved back, recessed threaded inserts or any other obstruction.

First, determine the diameter of the Bolt (i,j,k,l) your TV requires by hand threading them into the threaded insert on the back of the TV.

If you encounter any resistance, stop immediately! Once you have determined the correct diameter, see the appropriate Diagram below.

You will thread the Bolt through the appropriate Lock Washer (m,n,o,p), a Washer (s,t), the Monitor Bracket (c), a spacer (q,r) and nally

into the TV. For the M4 or M5 diameter bolt, you will need another M4/M5 Washer between the Monitor Bracket and the Spacer. Make

sure the Monitor Brackets are vertically centered on the TV and level with each other.

M4 Diameter Bolt M6 Diameter Bolt

i k

m o

s t

c c

q r

Diagram 2

M5 Diameter Bolt M8 Diameter Bolt

j l

n p

s t

c c

q r

Product specificaties

Merk:	Hitachi
Categorie:	Niet gecategoriseerd
Model:	VMPL2B

Heb je hulp nodig?

Als je hulp nodig hebt met Hitachi VMPL2B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Hitachi

Hitachi G23SCY Handleiding

2 November 2024

Hitachi NR1890DR Handleiding

7 December 2023

Hitachi WR16SE Handleiding

20 Augustus 2023

Hitachi CE18DSLP4 Handleiding

19 Augustus 2023

Hitachi CN 18DSL Handleiding

19 Augustus 2023

Hitachi RP350YDH Handleiding

18 Augustus 2023

Hitachi G12VE Handleiding

18 Augustus 2023

Hitachi S18SB Handleiding

17 Augustus 2023

Hitachi CB18DBLP4 Handleiding

17 Augustus 2023

Hitachi H60MEY Handleiding

17 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024