Hilti TE 15-C Handleiding

Hilti Boormachine TE 15-C

Lees hieronder de 📖 handleiding in het Nederlandse voor Hilti TE 15-C (4 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 196 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

TE15-C

Operating instructions

Mode d’emploi

Manual de instrucciones

*308372*

308372

P i t d 07 07 2013 | D N PUB / 5070796 / 000 / 00

General safety rules

SAVE THESE INSTRUCTIONS

2. Work Area

2.1 Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

2.2 Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable liquids,

gases, or dust. Power tools create sparks which may

ignite the dust or fumes.

2.3 Keep bystanders, children and visitors away while

operating a power tool. Distractions can cause you to

lose control.

3. Electrical Safety

3.1 Grounded tools must be plugged into an outlet

properly installed and grounded in accordance with

all codes and ordinances. Never remove the ground-

ing prong or modify the plug in any way. Do not use

any adaptor plugs. Check with a qualified electrician

if you are in doubt as to whether the outlet is properly

grounded. If the tools should electrically malfunction or

break down, grounding provides a low resistance path to

carry electricity away from the user.

Applicable only to Class I (grounded) tools.

3.2 Double insulated tools are equipped with a polar-

ized plug (one blade is wider than the other). This plug

will fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If it still

does not fit, contact a qualified electrician to install a

polarized outlet. Do not change the plug in any way.

Double insulation eliminates the need for the three-wireZ

grounded power cord and grounded power supply sys-

tem.

Applicable only to Class II tools.

3.3 Avoid body contact with grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is

an increased risk of electric shock if your body is ground-

ed.

3.4 Don’t expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk of

electric shock.

This instruction need not be provided for tools classified

watertight or splashproof.

3.5 Do not abuse the cord. Never use the cord to car-

ry the tools or pull the plug from an outlet. Keep cord

away from heat, oil, sharp edges or moving parts.

Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

3.6 When operating a power tool outside, use an out-

door extension cord marked «W-A» or «W». These

cords are rated for outdoor use and reduce the risk of

electric shock.

4. Personal Safety

4.1 Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

tool while tired or under the influence of drugs, alco-

hol, or medication. A moment of inattention while operat-

ing power tools may result in serious personal injury.

4.2. Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair, clothing,

and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

4.3 Avoid accidental starting. Be sure switch is off

before plugging in. Carrying tools with your finger on the

switch or plugging in tools that have the switch on invites

accidents.

4.4 Remove adjusting keys or wrenches before turn-

ing the tool on. A wrench or a key that is left attached to

a rotating part of the tool may result in personal injury.

4.5 Do not overreach. Keep proper footing and bal-

ance at all times. Proper footing and balance enables

better control of the tool in unexpected situations.

4.6 Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat or hearing

protection must be used for appropriate conditions.

5. Tool Use and Care

5.1 Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding

the workpiece by hand or against your body is unstable

and may lead to loss of control.

5.2 Do not force tool. Use the correct tool for your

application. The correct tool will do the job better and

safer at the rate for which it is designed.

5.3 Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with the switch is dan-

gerous and must be repaired.

5.4 Disconnect the plug from the power source

before making any adjustments, changing acces-

sories, or storing the tool. Such preventive safety mea-

sures reduce the risk of starting the tool accidentally.

5.5 Store idle tools out of reach of children and other

untrained persons. Tools are dangerous in the hands of

untrained users.

5.6 Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools with sharp cutting

edges are less likely to bind and are easier to control.

5.7 Check for misalignment or binding of moving

parts, breakage of parts and any other condition that

may affect the tools operation. If damaged, have the

tool serviced before using. Many accidents are caused

by poorly maintained tools.

5.8 Use only accessories that are recommended by

the manufacturer for your model. Accessories that may

be suitable for one tool may become hazardous when

used on another tool.

6. Service

6.1 Tool service must be performed only by qualified

repair personnel. Service or maintenance performed by

unqualified personnel could result in a risk of injury.

6.2 When servicing a tool, use only identical replace-

ment parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or fail-

ure to follow Maintenance Instructions may create a risk

of electric shock or injury.

Additional Specific Safety Rules:

101 Hold tools by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

«live» wire will make exposed metal parts of the tool «live»

and shock the operator.

102 Wear ear protectors when using the tool for

extended periods. Prolonged exposure to high intensity

noise can cause hearing loss.

1. WARNING!

Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personal injury.

P i t d 07 07 2013 | D N PUB / 5070796 / 000 / 00

Hilti TE15-C Rotary Hammer Drill

Technical data

Input power: 710 W

Voltage (versions): 120 V

Input current: 6.3 A

Frequenc y: 50–60 Hz

Speed under load: 0–730/min.

Hammering under load: 0–3850 blows/min.

Single impact energy: 2.2 Joules / 1.6 ft-lbs.

Drill bit size range: 4–28 mm dia. / 3/16″–11/8 ″dia.

Optimal performance dia.: 10–16 mm / 3/8″–5/

8″

Drilling performance in medium-grade

concrete with 12 mm dia. drill: 42 cm3 /min. 370 mm/min. / 110 inⳎ3/min.

Chiselling performance in medium-hard

concrete with pointed chisel: 180 cm3/min.

Chuck type: TE-C

Drill bit connection end: TE-C

Automatic cut-out brushes

Double insulation construction

With slip clutch

Dust-tight enclosure, central and permanent lubrication (maintenance free)

Variable speed switch

Side handle adjustable with depth gauge

Forwards/reverse switch

Right of technical modifications reserved

Do not use this product in any way other than as directed by these operating instructions.

The respective regulations of your trade association and the enclosed safety precautions

must be observed.

The operating instructions should always be kept with the machine!

Always wear ear

protectors.

Always wear pro-

tective gloves.

Always wear safety

glasses.

This Product is UL listed and CSA certified

Double insulation

P i t d 07 07 2013 | D N PUB / 5070796 / 000 / 00

Product specificaties

Merk:	Hilti
Categorie:	Boormachine
Model:	TE 15-C

Heb je hulp nodig?

Als je hulp nodig hebt met Hilti TE 15-C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Hilti

Hilti DD-BL DD 200 Handleiding

27 Mei 2023

Hilti SF 2H-A12 Handleiding

23 Mei 2023

Hilti UD 30 Handleiding

10 Mei 2023

Hilti TE DRS-C Handleiding

9 Mei 2023

Hilti TE 2-S Handleiding

8 Mei 2023

Hilti TE 50 Combi Handleiding

25 April 2023

Hilti DD VP-U 120V Handleiding

20 April 2023

Hilti SF 6H-22 Handleiding

17 April 2023

Hilti TE 2-M Handleiding

16 April 2023

Hilti DD-WMK-BL Handleiding

10 April 2023

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Festo DGSC-6-10-P-P Handleiding

21 November 2024

Cecotec CecoRaptor Handleiding

19 November 2024

Bavaria By Einhell BAS 18 S-2 Handleiding

19 November 2024

Bavaria By Einhell Bavaria BSM 1000 Handleiding

19 November 2024

Bavaria By Einhell BAS 24 S Handleiding

19 November 2024

Bavaria By Einhell Bavaria BSM 500 Handleiding

19 November 2024

Proviel HTM 1305/1 Handleiding

19 November 2024

Proviel HPAS 18 AK Handleiding

19 November 2024

Bavaria By Einhell BAS 24/1 Handleiding

19 November 2024

Bavaria By Einhell BAS 24 S-2A Handleiding

19 November 2024