Hikvision DS-6912UDI Handleiding

Hikvision Digitale decoders tuners DS-6912UDI

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-6912UDI (2 pagina's) in de categorie Digitale decoders tuners. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Trouble Shooting TipsExploded View of Wash System

Check the Following

1. Fuse (blown or tripped).

2. 120 VAC supply wiring connection

faulty.

3. Electronic control board defective.

4. No 12 VAC power to control.

5. Motor (inoperative).

6. Door switch (open contacts).

7. Door latch not making contact with

door switch.

8. Touch pad circuit defective.

9. No indicator lamps illuminate when

START or OPTIONS are pressed.

1. Motor (bad bearings).

2. Motor stuck due to prolonged

non-use.

1. Improper voltage.

2. Motor windings shorted.

3. Glass or foreign items in pump.

1. Heater element (open).

2. Electronic control board defective.

3. Wiring or terminal defective.

4. Hi-Limit thermostat defective.

1. Latch mechanism defective.

2. Electronic control board defective.

3. Wiring or terminal defective.

4. Broken spring(s).

5. Defective actuator.

1. Water supply turned off.

2. Defective water inlet fill valve.

3. Check fill valve screen for

obstructions.

4. Defective float switch.

5. Electronic control board defective.

6. Wiring or terminal defective.

7. Float stuck in “UP” position.

1. Drain hose (high) loop too low.

2. Drain line connected to a floor drain

not vented.

1. Detergent allowed to stand too long in

dispenser.

2. Dispenser wet when detergent was

added.

3. Detergent cover held closed or blocked

by large dishes.

4. Improper incoming water

temperature to properly dissolve

detergent.

5. See "Detergent cover will not open."

Always disconnect the dishwasher from the electrical power source before adjusting or

replacing components.

Personal Injury Hazard

Remedy

1. Replace fuse or reset breaker.

2. Repair or replace wire fasteners at

dishwasher junction box.

3. Replace control board.

4. Replace control board.

5. Replace motor/impeller assembly.

6. Replace latch assembly.

7. Replace latch assembly.

8. Replace console assembly.

9. Replace console assembly.

1. Replace motor assembly.

2. Rotate motor impeller.

1. Check voltage.

2. Replace motor/impeller assembly.

3. Clean and clear blockage.

1. Replace heater element.

2. Replace control board.

3. Repair or replace.

4. Replace thermostat.

1. Replace dispenser.

2. Replace control board.

3. Repair or replace.

4. Replace dispenser.

5. Replace dispenser.

1. Turn water supply on.

2. Replace water inlet fill valve.

3. Disassemble and clean screen.

4. Repair or replace.

5. Replace control board.

6. Repair or replace.

7. Clean or replace float.

1. Repair to proper

32-inch minimum

height

2. Install air gap at counter top.

1. Instruct customer/user.

2. Instruct customer/user.

3. Instruct customer/user on proper

loading of dishes.

4. Incoming water temperature of

120°F is required to properly

dissolve dishwashing detergents.

Symptom

Dishwasher will not operate when

turned on.

Motor hums but will not start or run.

Motor trips out on internal thermal

overload protector.

Dishwasher runs but will not heat.

Detergent cover will not latch or

open.

Dishwasher will not pump out.

Dishwasher will not fill with water.

Dishwasher water siphons out.

Detergent left in dispenser.

010108

Pump Assembly

The pump assembly is driven by a permanent

split capacitor motor. When looking at the output

shaft, rotation is in the counterclockwise direction

at 3300RPM when driven by 120V 60Hz AC

signal. The motor drives a pump which supplies

100% filtered water at the rate of approximately

19 GPM to all three spray arms at once.

Draining is accomplished by using a small

seperate synchronous drain pump mounted to

the sump. The drain pump is connected to the

sump by a small rubber hose and two mounting

points. A check valve is located at the discharge

end of the drain pump.

The drain valve is connected to the drain pump

by a rubber hose and is mounted to the

dishwasher base. The drain valve maintains

pressure in the pressurized fine filter. The

intermediate drain hose is attached by a worm

gear clamp to the discharge end of the drain

valve.

The drain hose must have a loop at a minimum

height of 32 inches in order to ensure proper

drainage.

The main pump is removed by disconnecting

both attached clamps and hoses, removing the

three screws that secure the motor base to the

dishwasher base, unlatching the leak detector,

and disconnecting the wiring harness

connections to the pump assembly.

Tub Gasket

The door gasketl is pressed into the tub channel

for an interference fit. To install the gasket:

1. Locate the center mark on the gasket and

press into place.

2. Press the gasket across the header using

your thumb.

Product Specifications

Electrical

Rating ...................................120 Volts, 60Hz

Separate Circuit..15 amp min.- 20 amp max.

Motor (Amps) ........................................... .75

Heater Wattage ..................................... 1200

Total Amps (load rated) ........................ 10.0

TempAssure .............................. 140°F ±5°F

(60°C±3°C) [with outer door in place]

TempBoost ............ 145°F ±5°F (63°C ±3°C)

Heated Wash/Heated Rinse

Sanitize .................. 150°F ±5°F (66°C ±3°C)

Hi-Limit Thermostat ............... 200°F (93°C)

Water Supply

Suggested minimum incoming water

temperature ............................ 120°F (49°C)

Pressure (PSI) min./max. .................. 20/120

Connection (NPT) .....................................3/ "8

Consumption (Normal Cycle) ......................

............ 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters

Water valve flow rate (U.S. GPM)............ .83

Water recirculation rate (U.S. GPM) ..............

.................................................... approx. 19

Water fill time ................................... 87 sec.

Detergent and Rinse Aid Dispenser

The detergent and rinse aid dispenser is a one

piece component consisting of a molded

detergent cup and a built-in rinse aid dispenser.

The detergent cup has a spring loaded cover

and the rinse aid dispenser has a removable

cover.

Liquid rinse aid is added to the dispenser up to

the fill line indicator. The amount of rinse aid

released can be adjusted by turning the arrow

indicator from one, being the least amount, to

four, being the greatest amount.

3. Press the gasket while stretching around

the corners .

NOTE: There should be no wrinkles or

puckers in the corners.

4. Place the gasket end at the bottom and

then press the gasket in from the bottom up.

Component Error LED Indication

To gain access to the Control Housing

Assembly, remove kickplate assembly. LED

indicates which component is the source of

the error.

To replace dispenser:

• shut off electricity to dishwasher,

• remove outer door panel assembly and foam

barrier,

• disconnect wiring to the dispenser,

• remove the six screws and bracket,

• remove the dispenser,

• replace and reinstall in reverse order,

• rewire actuator.

Standard Dry Air Flow

When the control advances to the “dry” portion of

the cycle, the lower fan located in the Lower

Drying Duct Assembly is activated. Then, the

Vent Assembly located in the top right corner of

the tub is activated. The vent fan draws in the air

from outside the tub forcing the hot, humid air out

the Side Drying Duct Assembly and into the

Lower Drying Duct Assembly. Cool dry outside

air is mixed with hot, humid air existing the tub

in the Lower Drying Duct Assembly. This lowers

the temperature and humidity of the air exiting

the unit through the toe and kickplate. The

addition of cooler, dryer outside air helps to

speed evaporation of water from the hot dishes.

3. Repair or replace.

3. Drain valve or pump stuck open.

6. Spray arm blocked.

7. Is water getting into unit.

6. Instruct customer/user.

7. Check fill valve repair or replace.

7. Defective Drain Valve. 7. Repair or replace.

1. Drain restricted.

2. Electronic control board defective.

3. Defective drain pump.

4. Blocked impeller.

5. Open windings.

6. Wiring or terminal defective.

1. Clear restrictions.

2. Replace control board.

3. Replace pump.

4. Check for blockage, clear.

5. Replace pump assembly.

6. Repair or replace.

Product specificaties

Merk:	Hikvision
Categorie:	Digitale decoders tuners
Model:	DS-6912UDI
Gewicht:	6400 g
Breedte:	440 mm
Diepte:	311 mm
Hoogte:	80 mm
AC-adapter ingangsspanning:	100 - 240 V
Ondersteund audioformaat:	AAC
Ondersteunde videoformaten:	H.264,H.264+,H.265,H.265+,M-JPEG,MPEG4
Ondersteunde video-modi:	720p,1080p
Maximale beeldsnelheid:	30 fps
Aantal Ethernet LAN (RJ-45)-poorten:	18
Vermogensverbruik (max):	108 W
Maximale videoresolutie:	3840 x 2160 Pixels
RS-232 port:	1
Ondersteunde grafische resoluties:	1024 x 768 (XGA),1280 x 720 (HD 720),1280 x 800 (WXGA),1280 x 960,1600 x 1200 (UXGA),1680 x 1050 (WSXGA+),1920 x 1080 (HD 1080)
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Bekabelingstechnologie:	10/100/1000BaseE-T(X)
Ethernet interface type:	Gigabit Ethernet
DVI output ports:	1
PTZ control:	Ja
Aantal kanalen:	12 kanalen
BNC output ports:	6
Aantal HDMI-uitgangen:	12
VGA (D-Sub) uitgang ports:	1
Alarmingangkanalen:	8
Bedrijfstemperatuur (T-T):	-10 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
RS-485 ports:	1
Live view:	Ja
Alarmuitgangkanalen:	8