Hifonics Brutus Elite BE40-1000.1D Handleiding

Hifonics Receiver Brutus Elite BE40-1000.1D

Lees hieronder de 📖 handleiding in het Nederlandse voor Hifonics Brutus Elite BE40-1000.1D (1 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your ampliîš¿er model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Attach the chassis ground
cable to the ampliîš¿er
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the ampliîš¿er +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the ampliîš¿er remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the ampliîš¿er. Choose a
location that is close to the
ampliîš¿er. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
5
7
6
8
11
12
4
High Level Input
- DC turn on
- Music Sense
Low Level Input
- REM turn on
(Remote wire turn on)
Please scan QR code below or go to
Hifonics.com/product-manuals for the
Auto-Sense Technical Guide.
Turn on Mode
9
Model Fuse Size Cable Size
4ga
0ga
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best îš¿ts your
speaker conîš¿guration.
Speaker
Connections
Stereo
Monoblock single woofer multiple woofersMonoblock
Bridged
10
MUSIC SENSE
DC SENSE
REMOTE
TURN ON MODE
NOTE - When using low level input and the RCA’s are plugged into the amplier and the TURN ON
MODE is in the DC ON position, the ampliîš¿er will NOT turn on. Please re-read QR document above
or hire a professional installer.
BE40-1000.1D
BE40-1500.1D
BE40-2000.1D
BE40-3000.1D
BE40-1500.2D
BE40-1500.4D
BE40-2000.5D
2x60A
External 150A
External 200A
External 300A
External 150A
External 150A
External 200A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the ampliîš¿er to
a secure surface. Do not mount
the ampliîš¿er upside down.
Disconnect
Negative Battery
Terminal
Run Cables
Mount Ampliîš¿er
Installation
1
2
3
CH1 CH2
CH1 CH2
Common System Setup
4ch - Full Range
4ch - Mixed Mono
Mono
5ch
CH1 CH2
2ch - Full Range


Product specificaties

Merk: Hifonics
Categorie: Receiver
Model: Brutus Elite BE40-1000.1D

Heb je hulp nodig?

Als je hulp nodig hebt met Hifonics Brutus Elite BE40-1000.1D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Hifonics

Handleiding Receiver

Nieuwste handleidingen voor Receiver