Hayward SandMaster SM2506T Handleiding

Hayward Niet gecategoriseerd SandMaster SM2506T

Lees hieronder de 📖 handleiding in het Nederlandse voor Hayward SandMaster SM2506T (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 170 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

IS 1706T HC 11

Your Sandmaster high rate sand lter is a high performance

totally corrosion-proof lter that blends superior ow

characteristics and features with ease of operation. It

represents the very latest in high rate sand lter

technology. It is virtually foolproof in design and operation

and when installed, operated and maintained according to

instructions, your lter will produce clear, sparkling water

with only the least attention and care.

HOW IT WORKS

The Sandmaster uses special lter sand to remove dirt

particles from pool water. Sand is loaded into the lter tank

and functions as the permanent dirt removing media. The

pool water, which contains suspended dirt particles, is

pumped through your piping system and is automatically

directed by the patented lter control valve to the top of

the lter tank. As the pool water is pumped through the

lter sand, dirt particles are trapped by the sand bed, and

ltered out. The cleaned pool water is returned from the

bottom of the lter tank, through the control valve and

back to the pool through the piping system. This entire

sequence is continuous and automatic and provides for

total recirculation of pool water through your lter and

piping system. After a period of time the accumulated dirt

in the lter causes a resistance to ow, and the ow

diminishes. This means it is time to clean (backwash) your

lter. With the control valve in the backwash position, the

water ow is automatically reversed through the lter so

that it is directed to the bottom of the tank, up through the

sand, ushing the previously trapped dirt and debris out of

the waste line. Once the lter is backwashed (cleaned) of

dirt, the control valve is manually resequenced to Rinse,

and then Filter, to resume normal ltering.

INSTALLATION

Only simple tools (screwdriver and wrenches), plus pipe

sealant for plastic adapters, are required to install and/or

service the lter.

The lter system should be placed on level, very rm

ground, or equivalent, as recommended by your pool

dealer. Position the lter so that the piping

connections, control valve and winter drain are

convenient and accessible for operation, servicing and

winterizing.

Assemble the Pump to the platform base. The exible

hose and adapters must now be installed to connect

the pump/lter system.

Screw straight adapter, using Teon pipe sealant

tape or Permatex No. 2, securely into 1 1/2" pump

discharge.

Screw other straight adapter, using Teon pipe

sealant tape or Permatex No. 2, securely into

opening in control valve marked PUMP. (Do not

overtighten.)

Place hose clamps on hose and t hose over

straight adapters and secure with clamps. If hose is

dicult to t over adapters, place hose in hot water

for several minutes.

NOTE: To prevent breakage and damage to pump and

control valve, use only pipe sealants specically formulated

for plastics. Do not overtighten ttings or adapters.

STOP here and load media per instructions (No. 3).

www.haywardpool.ca

SM2506T 3.14 0.29 63 238 50 3.45 18 45 18 45 300 136

SM2306T 2.64 0.25 53 200 50 3.45 18 45 18 45 250 114

SM2106T 2.20 0.20 44 161 50 3.45 18 45 18 45 225 100

SM1906T 1.80 0.17 40 151 50 3.45 18 45 18 45 175 80

SM1706T 1.50 0.14 38 144 50 3.45 18 45 18 45 125 57

FT² M² GPM LPM PSI BAR INCH CM INCH CM TYPE LBS KG

SPECIFICATIONS

.45 mm -

.55 mm

No 20 or No 1/2

Silica Filter

Sand

MEDIA REQUIRED

ABOVE CLEARANCESIDE CLEARANCE

MAXIMUM WORKING

PRESSURE

DESIGN FLOW RATE

EFFECTIVE

FILTRATION AREA

MODEL NO.

SP-0714TC

EC-2708-1

GM-600-F

GM-600-NM

S-170-DA

S-180-DA

S-210-DA

S-220-DA

S-244-DA

DP-10298-B

S-180-AB

S-210-AB

S-220-AB

S-244-AB

S-200-Q

S-180-LM

S-164-B

S-200-J

Vari-Flo Control Valve

6-Position

Pressure Gauge

Valve/Tank O-Ring

Flange Clamp (Valve Tank)

Lateral Assy. (SM1706T)

Lateral Assy. (SM1906T)

Lateral Assy. (SM2106T)

Lateral Assy. (SM2306T)

Lateral Assy. (SM2506T)

Filter Tank (SM1706T)

Filter Tank (SM1906T)

Filter Tank (SM2106T)

Filter Tank (SM2306T)

Filter Tank (SM2506T)

Lateral

Drain Cap & Gasket

Base (SM1706T)

Base (SM2306T, SM1906T,

SM2106T & SM2506T)

REF.

NO.

REQ’D.

PART NO. DESCRIPTION 1

6a 6b 6c 6d 6e

Figure A

www.haywardpool.ca

Loosen ange clamp and remove Filter Control Valve (if

previously installed).

Cap internal pipe with plastic cap to prevent sand from

entering it. Be sure pipe is securely in place in bottom

underdrain hub.

We recommend lling tank approximately 1/2 way

with water to provide a cushioning eect when the

lter sand is poured in. This helps protect the

under-drain laterals from excessive shock. (Be sure the

winter drain cap is securely in place on drain pipe.) Note:

Please check to conrm all laterals are in the down

position before loading with sand. See gure A.

Slowly pour in correct amount and grade of lter sand, as

specied. (Be sure center pipe remains centered in

opening.) Sand surface should be leveled and should

come to about the middle of the lter tank. Remove

plastic cap from internal pipe.

Loading sand media. Filter sand media is loaded through the

top opening of the lter.

Assemble Filter Control Valve to lter tank.

Place stainless steel valve ange clamp around neck of

tank. Do not tighten. Wipe lter ange clean.

Insert Filter Control Valve (with valve/ange o-ring in

place) into the tank neck, taking care that the center pipe

slips into the hole in the bottom of the valve. Place clamp

around valve ange and tank ange and tighten just

enough so that the valve may be rotated on tank for nal

positioning.

Carefully screw pressure gauge, with pipe tape, into 1/4

tapped hole in valve body. Do not overtighten.

Connect pump to control valve opening marked PUMP

according to instructions. After connections are made,

tighten valve ange clamp with screwdriver, tapping

around clamp with screwdriver handle to help seat valve

ange clamp.

Make return to pool pipe connection to control valve

opening marked RETURN and complete other necessary

plumbing connections, suction lines to pump, waste, etc.

Make electrical connections to pump per pump instructions.

To prevent water leakage, be sure winter drain cap is securely

in place and all pipe connections are tight.

INITIAL START UP OF FILTER

Be sure correct amount of lter sand media is in tank and

that all connections have been made and are secure.

Depress Vari-Flo control valve handle and rotate to

BACKWASH position. (To prevent damage to control valve

seal, always depress handle before turning.)

Prime and start pump according to pump instructions (be

sure all suction and return lines are open), allowing the lter

tank to ll with water. Once water ow is steady out the

waste line, run the pump for at least 2 minutes. The initial

backwashing of the lter is recommended to remove any

impurities or ne sand particles in the sand media.

Turn pump o and set valve to RINSE position. Start pump and

operate until water in sight glass is clear - about 1/2 to 1

minute. Turn pump o and set valve to FILTER position and

restart pump. Your lter is now operating in the normal lter

mode, ltering particles from the pool water.

Adjust pool suction and return valves to achieve desired ow.

Check system and lter for water leaks and tighten

connections, bolts, nuts, as required.

Note the initial pressure gauge reading when the lter is clean.

(It will vary from pool to pool depending upon the pump and

general piping system.) As the lter removes dirt and

impurities from the pool water, the accumulation in the lter

will cause the pressure to rise and ow to diminish. When the

pressure gauge reading is 8-10 Ibs. (4-6 BAR) higher than the

initial "clean" pressure you noted, it is time to backwash (clean)

the lter (see BACKWASH under Filter and Control Valve

Functions).

NOTE: During initial clean-up of the pool water it may be necessary

to backwash frequently due to the unusually heavy initial dirt

load in the water.

CAUTION: To prevent unnecessary strain on piping system and

valving, always shut o pump before switching Filter Control

Valve Functions positions.

To prevent damage to the pump and lter and for proper

operation of the system, clean pump strainer and skimmer

baskets regularly.

FILTER AND CONTROL VALVE FUNCTIONS

FILTER - Set valve to FILTER for normal ltering. Also use regular

vacuuming.

BACKWASH - For cleaning lter. When lter pressure gauge rises

8-10 Ibs. (4-6 BAR) above start-up (clean pressure): Stop the

pump, set valve to BACKWASH. Start pump and backwash until

waste water is clear. Approximately 2 minutes or less

depending on dirt accumulation. Proceed to RINSE.

RINSE - After backwashing, with pump o, set valve to RINSE. Start

pump and operated for about 1/2 to 1 minute. This assures

that all dirty water from backwashing is rinsed out of the lter

to waste, preventing possible return to the pool. Stop pump,

set valve to FILTER, and start pump for normal ltering.

WASTE - To bypass lter for draining or lowering water level and for

vacuuming heavy debris directly to waste.

RECIRCULATE - Water is recirculated through the pool system

by-passing the lter.

CLOSED - Shuts o ow from pump to lter.

VACUUMING - Vacuuming can be performed directly into the lter.

When vacuuming heavy debris loads, set valve to WASTE

position to bypass the lter and vacuum directly out to waste.

*NOTE: For new concrete or gunite pools, or where there is a large

amount of plaster dust or debris - start lter in FILTER position (not

BACKWASH) to prevent clogging of underdrain laterals.

www.haywardpool.ca

Product specificaties

Merk:	Hayward
Categorie:	Niet gecategoriseerd
Model:	SandMaster SM2506T

Heb je hulp nodig?

Als je hulp nodig hebt met Hayward SandMaster SM2506T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Hayward

Hayward Easy Chem Handleiding

16 Mei 2024

Hayward SandMaster SM2306T Handleiding

30 Mei 2023

Hayward Pro-Grid C9002SEP Handleiding

29 Mei 2023

Hayward ProSeries HB Handleiding

16 Mei 2023

Hayward SharkVac XL Pilot Handleiding

14 Mei 2023

Hayward AquaRite 100 Handleiding

18 April 2023

Hayward PMD15 Handleiding

8 April 2023

Hayward SandMaster SM1906T Handleiding

7 April 2023

Hayward Control Station Handleiding

24 Maart 2023

Hayward SandMaster SM2506T Handleiding

22 Maart 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Einhell WB 50 Handleiding

30 December 2025

Hisense HAF1800D Handleiding

30 December 2025

Eufy Outdoor / Indoor Siren Handleiding

30 December 2025

Lenco TTA-180TN Handleiding

30 December 2025

Pioneer CA-HR-PSA-EVO.003 Handleiding

30 December 2025

TC Electronic PLETHORA X1 Handleiding

30 December 2025

Pioneer CA-HM-FOR.004 Handleiding

30 December 2025

Pioneer CA-HR-PSA-EVO.002 Handleiding

30 December 2025

Brennenstuhl Tower Power Handleiding

29 December 2024

Brennenstuhl Eco-Line Handleiding

29 December 2024