Harley Davidson J02994 (2003) Handleiding
Harley Davidson
Motor
J02994 (2003)
Lees hieronder de 📖 handleiding in het Nederlandse voor Harley Davidson J02994 (2003) (2 pagina's) in de categorie Motor. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
INSTRUCTIONS
-J02994 REV. 10-10-2003
SHIFTER LINKAGE COVER
General
This “Harley-Davidson script”-style shifter-linkage cover kit
fits 1997 and later FXDWG (Dyna Wide Glide®) model motor-
cycles. This kit also fits 1993 and later Dyna models
equipped with Forward Control Kit 49080-03.
NOTE
A Service Manual for your model motorcycle is available
from any Harley-Davidson dealer.
Installation
1. See the Service Parts illustration. Obtain an upper mount-
ing bracket (2), lower mounting bracket (3), two 1/2-inch
long screws and the Allen wrench (6) from the kit.
2. See Figure 1. Assemble the upper and lower mounting
brackets onto the shaft of the ball screw shell at one
end of between the ball screw (3) andthe shifter rod (1),
the jam nut (2) so the shaft passes above the three
holes in the brackets.
Insert the two screws in the outboard holes of the lower
bracket, and use the Allen wrench to thread them part
way into the holes in the upper bracket. Do not fully
tighten the screws at this time.
3. Repeat Steps 1 and 2 at the other end of the shifter rod.
4. Position the linkage cover (1) on top of the linkage and
examine the fit.
• If the cover fits properly, proceed to Step 8.
• If the center holes in the front and rear upper mounting
brackets cannot be adjusted to line up with the holes
on the inboard side of the cover, the linkage will need
to be adjusted to accept the cover. Proceed to Step 5.
5. See Figure 1 (below) and SHIFTER LINKAGE
ADJUSTMENT in the Service Manual. To adjust the
length of the linkage, remove the link attaching nut (5)
and flat washer at the forward ball screw.
6. Loosen the jam nut (2) at the front end of the shifter rod,
and remove the mounting bracket installed in Step 3.
Rotate the forward ball screw shell to achieve the prop-
er length to allow mounting of the cover.
7. Re-attach the ball screw to the shifter lever with the flat
washer and nut removed in Step 5. Torque the nut on
the ball stud to 70-90 in-lbs (7.9-10.2 Nm).
Torque the jam nut on the shifter rod to 20-24 ft-lbs
(27.1-32.5 Nm).
8. Fasten the rear of the cover (1) to the rear upper bracket
using a short screw (5) from the kit. Fasten the front of
the cover to the front bracket with the remaining screw.
Tighten the cover securely to the upper brackets.
Position the cover upright over the shifter rod, and tight-
en the four remaining screws to clamp the brackets
securely to the ball screw shells.
9. If the linkage needed adjustment (Steps 5 through 7),
the position of the shift foot lever (6) may have
changed.
To return the lever to the original position, loosen the
socket head screw (7) holding the lever to the shaft. Pull
the lever from the shaft, rotate to the desired angle and
slide the lever back onto the shaft.
Torque the screw to 18-22 ft-lbs (24.4-29.8 Nm).
®
Kit Number 33878-04
1 of 2
Figure 1. Stock Shifter Linkage
i02475
1. Shifter rod
2. Jam nut (2)
3. Ball screw shell (2)
4. Shifter lever
5. Link attaching nut
6. Shift foot lever
7. Socket screw
2
31
4
5
2
6
3
7
-J02994 2 of 2
Service Parts
®
Shifter Linkage Cover
Date 10/03
Part No. 33878-04
Item Description (Quantity) Part No.
1 Linkage cover Not sold separately
2 Mounting bracket (upper) (2) 33879-04
3 Mounting bracket (lower) (2) 33880-04
4 Screw, button head, hex socket,
#10-24 x 1/2 in (4) 94381-92T
5 Screw, button head, hex socket,
#10-24 x 1/4 in (2) 3339
6 Allen wrench, 1/8 in Not sold separately
i02476
1
5
2
3
4
5
2
3
4
6
Product specificaties
| Merk: | Harley Davidson |
| Categorie: | Motor |
| Model: | J02994 (2003) |
Heb je hulp nodig?
Als je hulp nodig hebt met Harley Davidson J02994 (2003) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Motor Harley Davidson
13 Mei 2023
8 Mei 2023
5 Mei 2023
24 April 2023
21 April 2023
13 April 2023
26 Maart 2023
23 Maart 2023
12 Maart 2023
9 Maart 2023
Handleiding Motor
- Motor Yamaha
- Motor Aprilia
- Motor Benelli
- Motor BMW
- Motor BodyCraft
- Motor Danfoss
- Motor Derbi
- Motor Ducati
- Motor Elac
- Motor Emco
- Motor Honda
- Motor Husqvarna
- Motor Kawasaki
- Motor Kettler
- Motor KTM
- Motor Mercedes-Benz
- Motor Metabo
- Motor Milwaukee
- Motor Mitsubishi
- Motor Moto Guzzi
- Motor MV Agusta
- Motor Nautilus
- Motor Piaggio
- Motor Reebok
- Motor SMC
- Motor Suzuki
- Motor Texas
- Motor Victory
- Motor Zero
- Motor Joy-it
- Motor Juki
- Motor Mahindra
- Motor Beta
- Motor Triumph
- Motor Hyosung
- Motor TVS
- Motor GasGas
- Motor Indian
- Motor Bajaj
- Motor Mash
- Motor Hero
- Motor Cagiva
- Motor Chang Jiang
- Motor Ridley
- Motor Sherco
- Motor Royal Enfield
- Motor Anova
- Motor CRRCpro
Nieuwste handleidingen voor Motor
14 December 2024
3 December 2024
16 November 2024
16 November 2024
15 November 2024
15 November 2024
15 November 2024
14 November 2024
14 November 2024
14 November 2024