GFI System Orca Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor GFI System Orca (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
User Manual
O R C A
DELAY
Table of Contents
1 Inputs Page 1
2 Outputs 1
3 Expression Input 1
4 Tap-Tempo Input 2
5 Knobs and Buttons 3
8 Options 6
9 Global Settings 6
10 Exp ression / Ramping Setup 7
11 Factor y Reset 8
6 Footswitches and LEDs 4
7 Saving Presets 5
U S E R M A N U A L
1
User Manual
O R C A
DELAY
U S E R M A N U A L
1. Inputs
Orca accepts mono input or stereo inputs. For mono input operaon use a standard mono (TS) patch
cable and for stereo operaon use a stereo (TRS) cable. If the stereo input signals come from an
equipment that has separate Le and Right channel output jacks you will need to use a splier cable
like this:
TRS
TS
TS
To obtain the opmal sound quality, depending whether you use Mono or Stereo inputs,
the pedal must be congured accordingly. This is done in . Global Setngs
Hold the MODES buon for 2 secs to enter global seng.
Globals
1. Input
> MONO
> STEREO
2. Outputs
Orca may be used for mono output or stereo outputs. For mono output use a standard mono (TS)
patch cable and for stereo outputs use a stereo (TRS) cable. If the stereo output signals are fed to
an equipment that has separate Le and Right channel input jacks you will need to use a splier
cable like the one pictured above.
You do not need to conî…Šgure anything for using mono or stereo outputs.
Set to MONO when using mono input.
Set to STEREO when using stereo input.
2
User Manual
O R C A
DELAY
U S E R M A N U A L
OUTPUT
EXPRESSION
MONO IN
STEREO IN
TAP TEMPO
< use cable > TRS
< use cable > TS
MONO OUT
STEREO OUT
< use cable > TRS
< use cable > TS
3. Expression Input
An expression pedal may be used to control any one of the primary parameters, alternavely a tap
tempo pedal may be used to remotely send tap tempo signal to the pedal.
INPUT
Expression Pedal requirement.
Some expression pedal on the market has its
wiper connected to the Ring instead, this will
not work with Make sure you get the Orca.
suitable type : . Wiper-to-Tip
Wiper resistance value should be 10 to 20
KOhm.
4. Tap Tempo Input
A tap-tempo pedal may be connected to the EXP/TAP input to remotely tap in the tempo. The
switch contact must be ‘Normally-Opened’ (NO) type.
TS cable & plug
TAP
PEDAL
wiper
Tip
Ring
Resistance value
10K Ohm
to
25K Ohm
Auto detecon
Upon power up Orca will automacally detect the presence (or absence) of an expression
pedal or a tap-tempo pedal. Therefore, aî…­er plugging/unplugging the external gear you need
to reboot Orca to let it detect the changes.


Product specificaties

Merk: GFI System
Categorie: Niet gecategoriseerd
Model: Orca

Heb je hulp nodig?

Als je hulp nodig hebt met GFI System Orca stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd GFI System

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd