GFB G-Force III Handleiding

GFB Niet gecategoriseerd G-Force III

Lees hieronder de đź“– handleiding in het Nederlandse voor GFB G-Force III (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 134 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/20
GFB G-Force III
Installation Instructions
Part #3005
+61 2 9534 0099 www.gfb.com.ausales@gfb.com.au facebook.com/GFBturbo instagram.com/gofastbits
SETTINGS
PRESET
SCRAMBLE
2 intro-
The GFB G-Force III boost controller is designed to not only bring boost on as fast and accurately as possible on a
turbocharged vehicle, but also to provide you with an accurate wideband Air/Fuel Ratio gauge using an externally
connected wideband module. The G-Force III incorporates an advanced and unique boost control strategy that allows
the user fine control over the peak boost, rise rate, and closed-loop correction.
The G-Force III also features a revised interface, making menu navigation and setup as fast and simple as ever.
Features at a glance:
ŸMultifunction boost and AFR (Air/Fuel Ratio) gauge with simple menu button toggle
ŸLean AFR warning can be set to cut boost pressure if engine runs too lean under load
Ÿ6 individually programmable boost preset memories, selectable on-the-fly
ŸClosed-loop correction - helps prevent boost variations
ŸUnique scramble boost strategy - increase or decrease boost for a certain amount of time at the push of a button
ŸOverboost protection - shuts down the solenoid and flashes a warning if boost goes too high
ŸExternal input - can be used to activate scramble or select boost presets remotely
ŸAdjustable button illumination colours - match your car’s existing lighting
ŸAFR gauge can display Lambda or AFR, and can be configured for different fuel types
ŸBoost/vacuum gauge display - in BAR, kPa, or PSI
ŸPeak hold boost pressure display
Installing the Head Unit
The G-Force III casing is a ½ DIN size, allowing to be
mounted into one half of a standard stereo slot.
Alternatively, with its thin profile (18.5mm), the G-Force III
can be mounted on a vertical face of the dashboard, or
stood up on its edge using the supplied double-sided
mounting tape.
Intro
About the G-Force III
Installation
Wiring Diagram
Solenoid Valve Installation Diagram
Menu Navigation
Menu Structure
Quick Start Guide
Boost Presets
Setting the Boost Pressure
Duty Cycle
Gain
Sensitivity
Controller Functions
Scramble Boost
Lean Cutout
Overboost
Peak Hold
Display Setting - Units of Pressure
Input 1 Setup - External Trigger
Input 2 Setup - Wideband AFR
Stoichiometric Ratio
Boost Gauge Calibration
Colour Settings
Additional Info
Tips
Troubleshooting
Tech
Warranty
2
3
4
5
6
7
8
9
10
11
12
12
13
13
14
14
15
15
16
17
17
19
20
contents
about the g force iii
91.5mm
53.5mm
SETTINGS
PRE SET
SCRAMBLE
To intake manifold -
use small Tee to tap into
an existing vacuum hose
if necessary
1/8” I.D. vacuum hose Vacuum hose joiner
Loom
3-Port Boost
Control Solenoid
Black wire -
Vehicle ground (chassis)
Red wire -
+12V switched power source.
It is recommended to connect
via a 5A fuse (not supplied)
Blue wire - Input 1
(see notes below, and
pages 14 & 17 for details)
Optional Remote Trigger Circuit
Engine Bay Vehicle Interior
Yellow wire - Input 2
(Connect to Wideband module for AFR
display. See notes below for details)
Remote trigger button (not
supplied). Use any switch, button
or sensor that grounds the blue
wire when activated
Input 1 (blue wire) can be used as a remote trigger simply by connecting it to any kind of switch, button, or programmable ECU output that
grounds the blue wire to the vehicle earth when activated. For ideas on different ways to use this feature, see page 17. Once connected, the
function of Input 1 must be configured within the “In.1” sub-menu (see page 14).
Input 2 (yellow wire) may be connected to an external Wideband O2 control module/sensor (not supplied). Connect the yellow wire directly to
your wideband controller’s auxiliary 0-5V analogue output, then configure using the “In.2" sub-menu (see page 14).
If either the blue or yellow wire are not used, simply cut or bundle them and make sure they are insulated.
W
W
W
WWARNING!
ARNING!
ARNING!
ARNING!ARNING! DO NOT connect the blue or yellow wire to a 12V source as this could damage the unit.
3 installation-
wiring diagram
SETTINGS
PRESET
SCRAMBLE
(4-port solenoid available
separately. GFB Part # 3845)

Product specificaties

Merk: GFB
Categorie: Niet gecategoriseerd
Model: G-Force III

Heb je hulp nodig?

Als je hulp nodig hebt met GFB G-Force III stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd GFB

GFB

GFB G-Force III Handleiding

28 Juli 2023
GFB

GFB EX44 Handleiding

27 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024