Gembird EG-EM1 Handleiding

Gembird Elektriciteit meiter EG-EM1

Lees hieronder de 📖 handleiding in het Nederlandse voor Gembird EG-EM1 (4 pagina's) in de categorie Elektriciteit meiter. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Energy Meter

Model No. EG-EM1

Introduction

With the Energy Meter, you are now able to determine power costs of your power loads in the easiest way.

Proper use

The measurement range of the Energy Meter extends from 5W to 3680W. If values fall below or exceed

these limit values, exact measurement are no longer possible. Also the device could not be overloaded,

otherwise will be destroyed. There will be alarm for the power overloading.

The Energy Meter has been developed for monitoring and measuring electrical loads.

The Energy Meter is only certified for operation at 230V AC.

Only power loads with a power supply of 230V AC 50/60Hz may be connected.

The maximum power of any connected load may not exceed 3680W (max. current 16A).

It is only suitable for electrical appliances with resistive load.

Operation of the Energy Meter is only permitted in interior spaces and dry environments, Usage in the

open air is strictly forbidden!

Safety Instructions

This device is not a toy and does not belong to the hands of children.

Only connect the Energy Meter to certified protected contact outlets 230V AC 50/60Hz (10/16A) with a

ground wire.

The connected load may not exceed 3680W(16A).

The recommended operating temperature is between +5 to +40 . High temperature may lead to

overheating and can thereby permanently destroy the Energy Meter.

Avoid operating under adverse environmental temperatures or near flammable gases, vapour and dust.

For reasons of safety, never allow the device to be operated when in wet or in a damp environment

When cleaning or servicing, the device must be disconnected from every source of operating voltage.

Condensers in the device may still be charged, even if the device was disconnected from all voltage

sources.

Do not insert needles, metals or any other objects into the device.

Properties

Display current time (24 hours type), week, load power and cost tariff.

Display total used energy and accrued energy cost.

Display total recorded time, total ON time and percentage .

Dual programmable power tariffs.

Displaying line of power Blinks (fig4,the second line) if the load power is over 3680W

Connection, operation settings

Before you connect the Energy Meter to an outlet or power or power load, condensers in the device will be

charged. Five minutes later, the condensers will have enough power to sustain the normal display of LCD

then the current time and your desired power tariff must be set.

Suggestion:

It is better to take 8-12 hours to charge the condensers fully for the first time, in order

to make the rechargeable Li-batteries to achieve optimum performance.

The procedure for entering the time and power tariff is described as following:

A. The setting of current time and week

1. Press“+” “-“ buttons together to enter into system setting, first setting

is the current time.

2. With “+” button to increase the value of the blinking position, while

with “-“ button to decrease the value of the blinking position.

3. Press “MODE” button to select next position.

4. After the setting of week, press “MODE” button, the system will enter

into the setting of cost tariff 1.

B. The setting of cost tariff 1

1. Set the effect time of cost tariff 1.

2. Set the value of tariff 1.(it is cent as unit, such as: 10cent)

3. With “+” button to increase the value of the blinking position, while

with “-“ button to decrease the value of the blinking position.

4. Press “MODE” button to select next position.

5. Press “MODE” button, the system will enter into the setting of cost

tariff 2.

C. The setting of cost tariff 2

1. Set the effect time of cost tariff 2.

2. Set the value of tariff 2. .(it is cent as unit, such as: 10cent)

3. With “+” button to increase the value of the blinking position from 0 to

9,while with “-“ button to decrease the value of the blinking position.

4. Press “MODE” button to select next position.

5. Go on pressing the button “mode” until the display board of fig4

appears.

D. Press “MODE”, “+” “-” simultaneously to delete all data (the data of current time

and the week will not be deleted) after 5 seconds.

Introduction of display board

Three display boards are designed to display different figures, you can use “MODE” button to

select which board you want to browse.

1. Display of current time (24 hours type), week, load power and current cost tariff

2. Display of total record time, total used energy and accrued energy cost.

3. Display of total record time, total on time and percentage

Current cost tariff per hour

otal

measuring time with load

(ONh/RECh)

Product specificaties

Merk:	Gembird
Categorie:	Elektriciteit meiter
Model:	EG-EM1
Kleur van het product:	Wit
Ingangsspanning:	230 V
AC-ingangsfrequentie:	50 - 60 Hz
Type beeldscherm:	LCD