Apc AP7152B Handleiding

Apc Elektriciteit meiter AP7152B

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc AP7152B (1 pagina's) in de categorie Elektriciteit meiter. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

990-9943-001

6/2016

Current Meter

Installation Instructions

























pdu0415a

pdu0417a

pdu0420a

pdu0421a

Link - Rx/Tx

10 /100

Status

Serial Port

- Warning

- OK

- Overload

Reset

Press and hold

to invert display

Current Meter

L1 L3L2

- Warning

- OK

- Overload

pdu0110b

General Information

This section contains installation information for the following

equipment:

AP7152B, AP7155B, AP7175B

Additional Resources

The Current Meter User Guide contains complete operation and

configuration information. Additional documentation and

downloadable software and firmware is available on the applicable

product page on the website www.apc.com. To quickly find a product

page, enter the product name or part number in the Search field.

Inventory

Mounting options

Install the Current Meter in one of the two following ways using the

mounting brackets (provided): on the roof of the enclosure or on the

inside of the enclosure mounted on the vertical mounting rails.

Roof

Vertical Mounting rail



 The Display Interface

Configuring network settings and accessing the Current

Meter

The Current Meter is DHCP compatible. Connect the network cable to

the network port (



) and then apply power to the unit. When the

status LED (



) for the network connection is solid green, perform the

following to display the IP address.

If your network does not use a DHCP server, see the user’s guide for

your Current Meter for details on other methods for configuring the

TCP/IP settings.

• Press and hold the Control button  until “IP” appears on the

display .

• Release the Control Button and the IPv4 address will be

scrolled across the display twice.

Quantity Item

1 Configuration Cable

3 Cable retention trays with 12 flat head

screws and 24 wire ties

2 Vertical mounting brackets with 4 pan head

screws

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

To avoid possible electrical shock and equipment damage, use only the

supplied hardware.

Failure to follow these instructions will result in death or serious

injury.

 Attach the two mounting brackets to the Current Meter with

the screws (provided).

 Attach the cage nuts (provided with your enclosure) to the

inside of the roof.

Secure the mounting brackets attached to the Current Meter

to the cage nuts installed in the roof.

 You can mount multiple Current Meters on top of each other

using additional mounting brackets (provided).

 Attach the two mounting brackets to the back of the Current

Meter with the screws (provided).

 Install the cage nuts (provided with your enclosure) into the

vertical mounting rail.

Route the power cords to the top of the enclosure and

through the roof.

Attach the brackets to the mounting rail with the screws

(provided with your enclosure).

 Phase indicator LED: Indicates normal (green), warning

(yellow), or alarm (red) condition.

 Reset button: Resets the Current Meter without affecting

the attached devices.

 Display of the current used by the Current Meter and

attached devices:

• Shows the current being used per phase by the device attached

to the Current Meter.

• Cycles through in 3-second intervals, and goes through all 3

readings (3 phases).

 Control button:

• Press to change the reading of the current displayed on the

digital display.

• Press and hold for five seconds to view the

IP address of the Current Meter.

• Hold for an additional five seconds to view the orientation.

• Hold for an additional five seconds to change the

orientation.

 Serial port: Access internal menus by connecting this port

(RJ-11 modular port) to a serial port on your computer,

using the supplied serial cable (part number 940-0144A).

 Ethernet port: Connects the Current Meter to your

network, using a CAT-5 network cable.

 Status LED: Indicates the status of the Ethernet LAN

connection and the state of the Current Meter.

•Off–The Current Meter has no power.

•Solid green–The Current Meter has valid TCP/IP settings.

•Flashing green–The Current Meter does not have valid

TCP/IP settings.

•Solid orange–A hardware failure has been detected in the

Current Meter. Contact Customer Support at a phone number

on the back cover of this manual.

•Flashing orange–The Current Meter is making BOOTP

requests.

 Link LED: Indicates whether there is activity on the

network.

Two-Year Factory Warranty

This warranty applies only to the products you purchase for your use

in accordance with this manual.

Terms of warranty

Schneider Electric warrants its products to be free from defects in

materials and workmanship for a period of two years from the date of

purchase. Schneider Electric will repair or replace defective products

covered by this warranty. This warranty does not apply to equipment

that has been damaged by accident, negligence or misapplication or

has been altered or modified in any way. Repair or replacement of a

defective product or part thereof does not extend the original warranty

period. Any parts furnished under this warranty may be new or

factory-remanufactured.

Non-transferable warranty

This warranty extends only to the original purchaser who must have

properly registered the product. The product may be registered at

www.apc.com.

Exclusions

Schneider Electric shall not be liable under the warranty if its testing

and examination disclose that the alleged defect in the product does

not exist or was caused by end user’s or any third person’s misuse,

negligence, improper installation or testing. Further, Schneider Electric

shall not be liable under the warranty for unauthorized attempts to

repair or modify wrong or inadequate electrical voltage or connection,

inappropriate on-site operation conditions, corrosive atmosphere,

repair, installation, exposure to the elements, Acts of God, fire, theft, or

installation contrary to Schneider Electric recommendations or

specifications or in any event if the Schneider Electric serial number

has been altered, defaced, or removed, or any other cause beyond the

range of the intended use.

THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, BY

OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD,

SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN

CONNECTION HEREWITH. SCHNEIDER ELECTRIC DISCLAIMS

ALL IMPLIED WARRANTIES OF MERCHANTABILITY,

SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE.

SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL NOT BE

ENLARGED, DIMINISHED, OR AFFECTED BY AND NO

OBLIGATION OR LIABILITY WILL ARISE OUT OF, SCHNEIDER

ELECTRIC RENDERING OF TECHNICAL OR OTHER ADVICE OR

SERVICE IN CONNECTION WITH THE PRODUCTS. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE

AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE

WARRANTIES SET FORTH ABOVE CONSTITUTE SCHNEIDER

ELECTRIC’S SOLE LIABILITY AND PURCHASER’S EXCLUSIVE

REMEDY FOR ANY BREACH OF SUCH WARRANTIES.

SCHNEIDER ELECTRIC WARRANTIES EXTEND ONLY TO

PURCHASER AND ARE NOT EXTENDED TO ANY THIRD

PARTIES.

IN NO EVENT SHALL SCHNEIDER ELECTRIC, ITS OFFICERS,

DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY

FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE

DAMAGES, ARISING OUT OF THE USE, SERVICE OR

INSTALLATION, OF THE PRODUCTS, WHETHER SUCH

DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF

FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER

SCHNEIDER ELECTRIC HAS BEEN ADVISED IN ADVANCE OF

THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY,

SCHNEIDER ELECTRIC IS NOT LIABLE FOR ANY COSTS, SUCH

AS LOST PROFITS OR REVENUE, LOSS OF EQUIPMENT, LOSS

OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA,

COSTS OF SUBSTITUENTS, CLAIMS BY THIRD PARTIES, OR

OTHERWISE.

NO SALESMAN, EMPLOYEE OR AGENT OF SCHNEIDER

ELECTRIC IS AUTHORIZED TO ADD TO OR VARY THE TERMS

OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF

AT ALL, ONLY IN WRITING SIGNED BY AN SCHNEIDER

ELECTRIC OFFICER AND LEGAL DEPARTMENT.

Warranty claims

Customers with warranty claims issues may access the Schneider

Electric customer support network through the Support page of the

website, www.apc.com/support. Select your country from the

country selection pull-down menu at the top of the page. Select the

Support tab to obtain contact information for customer support in your

region.

Customer support and warranty information is available at www.apc.com.

Product specificaties

Merk:	Apc
Categorie:	Elektriciteit meiter
Model:	AP7152B
Kleur van het product:	Zwart
Gewicht:	1840 g
Breedte:	178 mm
Diepte:	140 mm
Hoogte:	44 mm
Soort:	Elektronisch
Certificering:	RoHS
Ingangsspanning:	220 - 250 V
Eenheid van de maatregel:	A
Meetfuncties:	Powerbankknop
Bedrijfstemperatuur (T-T):	-5 - 45 °C
Type beeldscherm:	LCD
Nominale netspanning:	16 A
Toepassing:	Plug-in