GE JX2130SH Handleiding

GE Magnetron JX2130SH

Lees hieronder de 📖 handleiding in het Nederlandse voor GE JX2130SH (8 pagina's) in de categorie Magnetron. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
PART QUANTITY
Trim Frame 1
Bottom Duct 1
Top Bracket 1
Phillips Round-Head
24
Screws
(21 or 22 required
for installation)
Phillips Flat-Head 5
Screws (4 required
for installation)
Anti-Tip Bracket 1
Bottom Bracket 1
Template 1
PARTS INCLUDED
Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: www.GEAppliances.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions
JX7227/JX7230/JX2127SH/JX2130SH
Read these instructions completely and carefully.
• IMPORTANT – Save these
instructions for local inspector’s use.
• IMPORTANT – Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• For easier installation and personal safety, we recommend
that two people install this microwave oven.
• Unplug the microwave oven before attempting
installation of this kit.
BEFORE YOU BEGIN
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is UL listed for installation alone or over
any General Electric/Hotpoint single electric wall oven.
TOOLS YOU WILL NEED
#2 Phillips
screwdriver
Pencil
Tape measureAwl or punch
Drill with 7ø64” bit or #35
1
FOR YOUR SAFETY:
WARNING – Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
Scissors (optional)
2
CUTOUT DIMENSIONS
* Min. depth with receptacle outside cabinet 191ø2”
Min. depth with receptacle inside cabinet 22”
Installation Instructions
Models 27” 30”
Height 163ø4” 163ø4”
Width 251ø2” 251ø2”
Depth (min.)* 191ø2” ” or 22 191ø2” ” or 22
On 27” models, allow 11ø4” at the top, 9ø16” on the sides
and 1 at the bottom for overlap of the Trim Frame over ”
the edges of the cutout.
On 30” models, allow 11ø4”at the top, 21
ø8” on the sides
and 1 at the bottom for overlap of the Trim Frame over ”
the edges of the cutout.
For ADA Compliance, the microwave must be installed
no higher than 361ø4”.
Depth
Height
1”overlap
Width
INSTALL BOTTOM BRACKET AND
BOTTOM DUCT
2
Fit the tab on the bottom bracket into the slot on the
back of the bottom duct, and push down until the
bracket is flush with the bottom of the duct. Fasten
the bottom bracket to the bottom duct by using two
round-head screws.
Disconnect the microwave oven before proceeding
with the installation.
Remove any loose items inside the microwave
oven, including the turntable and turntable support.
Carefully turn the microwave oven upside down.
Line up the tabs on the bottom duct with the slots
on the bottom of the microwave and insert the tabs
into the slots. Secure the bottom duct with four
round-head screws as shown.
A
C
B
D
Front
Rear
Screws
Screws
Screws
Microwave Oven Upside Down
1
11ø4” overlap
1” Clearance
beyond Trim Frame
(on all sides)
27” Models: 9ø16”overlap
30” Models: 21ø8” overlap
3” min.
CAUTION
This trim kit uses air flow from the top, bottom and
sides of the trim frame. Blocking the air flow can
cause the microwave to function improperly and may
cause damage to the microwave.
Allow a 1” clearance beyond the edge of the Trim
Frame to provide proper air flow.
3
Installation Instructions
INSTALL THE ANTI-TIP BRACKET
3
Draw a line on the cutout floor at the center of the
cutout, and extend the line 1ø2”down the face of the
cabinet.
Fold or cut the front edge of the template, along the
front guide line. Place the template flush along the
front edge of the cutout floor, aligning the center
line of the template with the center line of the cutout
floor. Mark the centers of the two screw holes with
an awl or center punch for the anti-tip bracket
location as shown.
Remove the template and drill two holes for the
anti-tip bracket.
Install the anti-tip bracket onto the cutout floor
using two round-head screws.
A
B
C
Cutout Floor
Screws
Anti-Tip Bracket
D
INSTALL MICROWAVE OVEN INTO
CABINET
4
Slide the microwave oven part way into the cabinet
opening.
Plug in the microwave oven.
The bottom bracket must be flat to the cutout
floor to engage correctly with the anti-tip bracket
as shown. Carefully slide the microwave oven
back, engaging the anti-tip bracket. Make sure the
power cord is not mashed or cut as you slide the
microwave into place.
Center the microwave oven within the
cutout opening.
Ensure the microwave oven is accurately centered.
Line up the center line on the cabinet with the
triangular hole on the front of the bottom duct.
Drill pilot holes through the positioning flange and
then install five round-head screws
at the front of the bottom duct as shown.
A
B
C
Anti-Tip Assembly
Bottom Duct
Bottom Bracket
Anti-Tip
Bracket
D
E
Cutout Opening
Screws
F
Positioning
Flange
Screw Models
4 JX7227SFSS,JX7230SFSS,
JX7230EHES
5 JX7227DFBB,JX7227DFWW,
JX7230DFBB,JX7230DFWW,
JX2127SH, JX2130SH

Product specificaties

Merk: GE
Categorie: Magnetron
Model: JX2130SH

Heb je hulp nodig?

Als je hulp nodig hebt met GE JX2130SH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Magnetron GE

GE

GE JX827BMTS Handleiding

18 November 2024
GE

GE JX9152ELDS Handleiding

18 November 2024
GE

GE JVM6175SFSS Handleiding

16 November 2024
GE

GE Profile PVM9195DFCC Handleiding

16 November 2024
GE

GE PVM9215DFWW Handleiding

16 November 2024
GE

GE UVM9125STSS Handleiding

15 November 2024
GE

GE Profile PWB7030SVSS Handleiding

27 Oktober 2024
GE

GE GCHK07N1WSS Handleiding

23 Oktober 2024
GE

GE GCST07N1WBB Handleiding

23 Oktober 2024
GE

GE GCHK07N1WWW Handleiding

23 Oktober 2024

Handleiding Magnetron

Nieuwste handleidingen voor Magnetron

Panasonic

Panasonic NN-K5441 JF Handleiding

23 November 2024
Panasonic

Panasonic NN-GT556W Handleiding

23 November 2024
Panasonic

Panasonic NN-GF339M Handleiding

23 November 2024
Panasonic

Panasonic NN-K5442 MF Handleiding

23 November 2024
Panasonic

Panasonic NN-GF381M Handleiding

23 November 2024
Panasonic

Panasonic NN-GF557M Handleiding

23 November 2024
Panasonic

Panasonic NN-SM321H Handleiding

23 November 2024
Panasonic

Panasonic NN-S553 MF Handleiding

23 November 2024
Panasonic

Panasonic NN-ST651 Handleiding

23 November 2024
Panasonic

Panasonic NN-K5440 MF Handleiding

23 November 2024