GE JX1530MWW Handleiding

GE Magnetron JX1530MWW

Lees hieronder de 📖 handleiding in het Nederlandse voor GE JX1530MWW (4 pagina's) in de categorie Magnetron. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
PARTS INCLUDED
NOTE: This kit has extra screws to prevent the
technician from spending extra time locating a
replacement screw during installation.
PART QUANTITY
❒ Trim Frame 1
❒ Bottom Duct 1
❒ Top Bracket 1
❒ Bottom Bracket 1
❒ Upper Duct 1
❒ Rear Duct 1
❒ 4 mm x 14 mm 22 required
Round-Head 2 extra
Screws
❒ 4 mm x 14 mm 4 required
Flat-Head 2 extra
Screws
❒ Anti-Tip Brace 1
❒ Anti-Tip Bracket 1
❒ Template 1
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions JX1527 JX1530
1
❒
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT —Save these instructions
for local inspector’s use.
•IMPORTANT —Observe all governing
codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions for
future reference.
•Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
•Completion time – 1 to 3 hours
•Proper installation is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
•This kit is UL listed for installation alone
or over any GE/GE Profile single electric wall oven.
•For easier installation and personal safety, we
recommend that two people install this microwave
oven.
•Unplug the microwave oven before attempting
installation of this kit.
•This kit is for use on models: PEB1590DMBB,
PEB1590DMWW and PEB1590SMSS.
•Do not alter or modify any part of this kit or the
oven.
WARNING —This oven must
be plugged into a properly grounded 3-hole, 120V
receptacle as required by the National Electrical Code.
FOR YOUR SAFETY:
WARNING —Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
TOOLS YOU WILL NEED
2
Installation Instructions
❒ #2 Phillips Screwdriver
❒ Tape Measure
❒ Drill with 7/64″Bit or #35
❒ Scissors (Optional)
❒ Pencil
❒ Awl or Punch
❒
CUTOUT DIMENSIONS
WARNING — This trim kit uses air
flow from the top, bottom and sides of the
trim frame. Blocking the air flow can cause
the microwave to function improperly and
may cause damage to the microwave.
Allow a 1″clearance beyond the edge of the
trim frame to provide proper air flow.
1
Depth
Height
11⁄2″Overlap
Width
11⁄2″Overlap
1″Clearance
beyond trim frame
(on all sides)
3″Min.
27″Models: 1
1⁄2″overlap
30″Models: 3″overlap
❒
CUTOUT DIMENSIONS (CONT.)
On 27″models, allow 11⁄2″on all sides for
overlap of the trim frame over the edges of
the cutout.
On 30″models, allow 11⁄2″at the top and
bottom and 3″ on each side for overlap of
the trim frame over the edges of the cutout.
FOR INSTALLATION ABOVE A
BUILT-IN OVEN:
Microwave oven should be installed on a 3/8″
plywood base and supported by 2x4 or 1x2
equivalent runners on all sides. Base must be
capable of supporting a minimum of 100 lbs.
1
*Min. depth with 120V–60 Hertz grounded power
receptacle outside cabinet 211⁄2″
Min. depth with 120V–60 Hertz grounded power
receptacle inside cabinet 23″
Models 27″30″
Height 183⁄4″183⁄4″
Width 24″±1⁄ ±16″24″1⁄16″
Depth (min.)* 211⁄2″or 23″211⁄2″or 23″
❒
INSTALL THE ANTI-TIP BRACE
Draw a line on the cutout floor at the
center of the cutout, and extend the line
1/2″down the face of the cabinet.
Fold or cut the front edge of the template,
along the front guide line. Place the
template flush along the front edge of the
cutout floor, aligning the center line of
the template with the center line of the
cutout floor. Mark the centers of the two
screw holes with an awl or center punch
for the anti-tip brace location as shown.
Remove the
template and drill
two holes for the
anti-tip brace.
Install the anti-tip
brace onto the
cutout floor using
two round-head
screws.
D
C
B
A
2
Round-Head
Screws
Anti-Tip
Brace
Cutout
Floor
Center
Line
BA
C
DIMENSIONS:
A = 13⁄16″
B = 3″
C = 201⁄16″
❒ Level
Installation Instructions
❒ INSTALL BOTTOM DUCT
ASSEMBLY TO MICROWAVE OVEN
Fasten the anti-tip bracket to the bottom
duct using four round-head screws.
Install the rear duct to the bottom duct
with one round-head screw.
Remove all loose items, including the
turntable and turntable support, from the
microwave oven. Carefully turn the oven
upside down. Remove three screws (one
from control side, and two from bottom
rear) from microwave oven cabinet.
Place the bottom duct assembly on the
microwave oven bottom and fasten with
four round-head screws and the screws
just removed from the microwave oven.
Turn the microwave oven right side up,
being careful not to bend the bottom
duct flange.
C
B
A
3
Anti-Tip
Bracket
Round-Head
Screws (4)
Bottom Duct FRONT
REAR
Rear Duct
Round-Head Screw
❒
INSTALL UPPER DUCT AND
TOP BRACKET
Remove two screws from back of the
microwave oven. Peel off the adhesive
backing from the upper duct and secure
it to the microwave oven by pressing it
firmly down on duct. Fasten the upper
duct with the two screws just removed
from the microwave oven.
Place the top bracket on top of the upper
duct, with the opening on the top bracket
lined up with the opening on the duct.
Attach the top bracket to the upper duct
using two round-head screws.
B
A
4
Microwave oven
upside down
Screw from
microwave oven
Round-Head
Screws (4)
Round-Head
Screws
❒
INSTALL MICROWAVE OVEN
INTO CABINET
Slide the microwave oven part way into
the cabinet opening.
Plug in the
microwave
oven.
The anti-tip
bracket
must be
flat to the
cutout floor to engage correctly with the
anti-tip brace as shown. Carefully slide
the microwave oven back, engaging the
anti-tip brace. Make sure the power cord
is not mashed or cut as you slide the
microwave into place.
Center the microwave oven within the
cutout opening.
D
C
B
A
5
Anti-Tip
Assembly
Bottom Duct
Anti-Tip
Bracket
Anti-Tip
Brace
Screws
from
microwave
oven
Round-Head
Screws
3

Product specificaties

Merk: GE
Categorie: Magnetron
Model: JX1530MWW

Heb je hulp nodig?

Als je hulp nodig hebt met GE JX1530MWW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Magnetron GE

GE

GE Café CSA1201RSS Handleiding

30 November 2024
GE

GE JVM3160DFCC Handleiding

30 November 2024
GE

GE JX827BMTS Handleiding

18 November 2024
GE

GE JX9152ELDS Handleiding

18 November 2024
GE

GE JVM6175SFSS Handleiding

16 November 2024
GE

GE Profile PVM9195DFCC Handleiding

16 November 2024
GE

GE PVM9215DFWW Handleiding

16 November 2024
GE

GE UVM9125STSS Handleiding

15 November 2024
GE

GE Profile PWB7030SVSS Handleiding

27 Oktober 2024
GE

GE GCHK07N1WSS Handleiding

23 Oktober 2024

Handleiding Magnetron

Nieuwste handleidingen voor Magnetron

Whirlpool

Whirlpool MWSC 933 SW Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 9133 SX Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 933 SB Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 9133 SB Handleiding

3 December 2024
Whirlpool

Whirlpool MWF 259 B Handleiding

3 December 2024
Whirlpool

Whirlpool JT 469 BL Handleiding

3 December 2024
Whirlpool

Whirlpool MWP 253 SB Handleiding

3 December 2024
Whirlpool

Whirlpool Extra Space Crisp MWF 426 Handleiding

3 December 2024
Whirlpool

Whirlpool WMF250G Handleiding

3 December 2024
Gorenje

Gorenje MO23ORAW Handleiding

2 December 2024