GE 27831 Handleiding

GE Telefoon 27831

Lees hieronder de 📖 handleiding in het Nederlandse voor GE 27831 (4 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installing the Phone

Installing the Handset Battery

NOTE: You must connect the handset battery before use.

CAUTION: To reduce the risk of ﬁre or personal injury, use only

the ATLINKS USA, Inc. Nickel-Cadmium battery model 5-2459,

which is compatible with this unit.

1. Locate battery and battery door which are packaged together inside a plastic bag

and are separate from the handset.

2. Locate the battery compartment on the back of the handset.

3. Plug the battery pack cord into the jack inside the compartment.

NOTE: To ensure proper battery installation, the connector is keyed

and can be inserted only one way.

4. Set the ringer switch (on the handset) to ON, and place the handset in the cradle on

the base.

5. The in use/charge indicator turns on, verifying the battery is charging. The unit will

take 20 seconds to register and verify its security code.

NOTE: In case of a power failure, the handset may display

UNAVAILABLE when the TALK/CALL BACK button is pressed. You

must then place all handsets on the main base cradle for 20

seconds to re-register.

6. Allow the phone to charge for 16 hours prior to rst use. If you don’t properly charge

the phone, battery performance is compromised.

CAUTION: Use only the ATLINKS USA, Inc. 5-2616

(black) or

5-2617 (gray) power adapter that came with this unit. Using

other power adapters may damage the unit

Extra Charge Cradle (applicable only with Model 27831xx2)

1. Plug the extra charging cradle into the electrical outlet.

2. Place the handset on the charging cradle.

3. The charge indicator turns on, verifying the battery is charging.

4. Allow the phone to charge for 16 hours prior to rst use.

VERY IMPORTANT: BOTH HANDSETS MUST BE REGISTERED TO THE

MAIN BASE BEFORE USE. After the 2nd handset has charged for 16

hours, place it on the main base station for 20 seconds, it will then

automatically register and verify its security code.

Wall Mounting

If you want to mount the phone on a wall, slip the mounting holes (on the back of

the base) over the wall plate posts, and slide the unit down into place. (Wall plate not

included.)

Handset Setup

There are ve programmable menus available: Language, Local Area Code, Ringer

Tone, Tone/Pulse and Factory Default. When you program these settings, make sure the

phone is (not in talk mode). Pressing the TONE*/exit button will remove you from the OFF

menu selection process without changing the feature you are in.

Display Language

1. Press the FLASH/program button until shows in the display.1ENG 2FRA 3ESP

2. Use the CID/VOL (left or right arrow) button or the handset number pad to select 1

(English), 2 (French), or 3 (Spanish). The default setting is “1ENG”.

3. Press the FLASH/program button to conrm and to advance to the next menu

feature.

Local Area Code

If you enter your local 3-digit area code in the area code menu, your local area code

does not display on the Caller ID (CID) list. Instead, you only see the local 7-digit number.

Calls received from outside your local area code will display the full 10-digit number.

1. Press the FLASH/program button until shows in the display. The AREA CODE - - -

default setting is “- - -”.

2. Use the handset number pad to enter your 3-digit area code.

NOTE: If you make a mistake, press the CHAN/delete button to erase

the incorrect area code and repeat step 2.

3. Press the FLASH/program button to conrm and to advance to the next menu

feature.

Ringer Tone

1. Press the FLASH/program button until shows in the display. RINGER TONE

2. Use the CID/VOL (left or right arrow) button or the handset number pad (1-3) to enter

your selection from Ringer Tone 1, 2, or 3. The default setting is “RINGER TONE 1”.

3. Press the FLASH/program button to conrm and to advance to the next menu

feature.

Tone/Pulse

1. Press the FLASH/program button until shows in the display.1 TONE 2 PULSE

2. Use the CID/VOL (left or right arrow) button or the handset number pad to enter

your selection. The default setting is “1 TONE”.

4. Insert the battery pack.

5. Close the battery compartment by pushing the door up until it snaps into place.

Base Station

1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and

place your cordless telephone on a level surface, such as a desktop or tabletop, or

you may mount it on the wall.

Introduction

CAUTION: When using telephone equipment, there are basic

safety instructions that should always be followed. Refer to the

IMPORTANT SAFETY INSTRUCTIONS provided with this product

and save them for future reference.

IMPORTANT: Because cordless phones operate on electricity, you

should have at least one phone in your home that isn’t cordless, in

case the power in your home goes out.

Before You Begin

Parts Checklist

(for 27831xx1 model)

Make sure your package includes the items shown here.

For there will be additional handset, charge cradle, battery pack Model 27831xx2 ONE

and cover than shown above.

IMPORTANT: You can only use one handset at a time and there is NO

conference and intercom features for these units.

Telephone Jack Requirements

To use this phone, you need an RJ11C type modular telephone

jack, which might look like the one pictured here, installed in your

home. If you don’t have a modular jack, call your local phone

company to nd out how to get one installed

Installation

Digital Security System

Your cordless phone uses a digital security system to protect against false ringing,

unauthorized access, and charges to your phone line.

INSTALLATION NOTE: Some cordless telephones operate at

frequencies that may cause or receive interference with nearby

TVs, microwave ovens, and VCRs. To minimize or prevent such

interference, the base of the cordless telephone should not be

placed near or on top of a TV, microwave ovens, or VCR. If such

interference continues, move the cordless telephone farther away

from these appliances.

Certain other communications devices may also use the 2.4 GHz

frequency for communication, and, if not properly set, these

devices may interfere with each other and/or your new telephone.

If you are concerned with interference, please refer to the owner’s

manual for these devices on how to properly set channels to avoid

interference. Typical devices that may use the 2.4 GHz frequency

for communication include wireless audio/video senders, wireless

computer networks, multi-handset cordless telephone systems, and

some long-range cordless telephone systems.

Important Installation Guidelines

• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave

ovens, heating appliances and direct sunlight.

• Avoid areas of excessive dust, moisture and low temperature.

• Avoid other cordless telephones or personal computers.

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is specically

designed for wet locations.

• Never touch non-insulated telephone wires or terminals, unless the telephone line

has been disconnected at the network interface.

• Use caution when installing or modifying telephone lines.

Model 27831 Series

2.4 GHz Cordless

Telephone System

User’s Guide

Equipment Approval Information

Your telephone equipment is approved for connection to the Public Switched Telephone Network

and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical

Requirements for Telephone Terminal Equipment published by ACTA.

1 Notiﬁcation to the Local Telephone Company

On the bottom of this equipment is a label indicating, among other information, the US number

and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this

information to your telephone company.

The REN is useful in determining the number of devices you may connect to your telephone line

and still have all of these devices ring when your telephone number is called. In most (but not all)

areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain

of the number of devices you may connect to your line as determined by the REN, you should

contact your local telephone company.

A plug and jack used to connect this equipment to the premises wiring and telephone network

must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A

compliant telephone cord and modular plug is provided with this product. It is designed to be

connected to a compatible modular jack that is also compliant. See installation instructions for

details.

Notes

• This equipment may not be used on coin service provided by the telephone company.

• Party lines are subject to state tariffs, and therefore, you may not be able to use your own

telephone equipment if you are on a party line. Check with your local telephone company.

• Notice must be given to the telephone company upon permanent disconnection of your

telephone from your line.

• If your home has specially wired alarm equipment connected to the telephone line, ensure

the installation of this product does not disable your alarm equipment. If you have questions

about what will disable alarm equipment, consult your telephone company or a qualied

installer.

US Number is located on the cabinet bottom.

REN Number is located on the cabinet bottom.

Handset Layout

3. Press the FLASH/program button to conrm and to advance to the next menu

feature.

NOTE: For Model 27831xx2, this setting should be changed on both

handsets.

Factory Default

This feature allows you to restore the unit’s original features.

1. Press the FLASH/program button until DEFAULT shows in the display.

2. Use the CID/VOL (left or right arrow) button to scroll to YES. The default setting is

“NO”.

3. Press FLASH/program to conrm. You will hear a conrmation tone.

Cordless Phone Basics

Making a Call

1. Press the TALK/call back button and dial the desired number.

-OR-

To perform preview dial, dial the number rst then press the TALK/call back button.

2. To hang up, press the TALK/call back button or place the handset in the cradle.

Receiving a Call

1. To answer a call press the TALK/call back button on the handset before you begin

speaking.

2. To hang up, press the TALK/call back button or place the handset in the cradle.

Call Transfer (applicable only with Model 27831xx2)

During an external call, you may transfer the call to another handset.

1. Press the FORMAT/transfer button on originating handset. shows in TRANSFERRING

the display. Both handsets will be paged.

2. Press the FORMAT/transfer or TALK/call back button on the receiving handset to

answer the call.

NOTE: To cancel the call transfer, you may press the TONE*/exit or

the

FORMAT/transfer

button on the originating handset.

Redial

Press the REDIAL button to quickly dial the last number you called (up to 32 digits).

If you get a busy signal, and want to keep dialing the number, press redial to dial the

number again.

In Use Indicator

When the in use/charge indicator on the base is lit, the handset is either in use or

charging. The in use/charge indicator on the base ashes when you receive a call.

Flash

If you subscribe to the combined Call Waiting Caller ID service from your local

telephone company you will receive Caller ID information (if available) on Call Waiting

calls. During a phone call, you will hear a beep to indicate another call is waiting on

the line and Caller ID information for the waiting call shows on the handset display. To

connect the waiting call, press the FLASH/program button on the handset and your

original call is put on hold. You may switch back and forth between the two calls by

pressing the FLASH/program button.

TIP: Do not use the TALK/call back button to activate custom calling

services such as call waiting, or you’ll hang up the phone.

Volume

When the phone is , press the CID/VOL (left or right arrow) on the handset to adjust ON

the volume of the handset’s earpiece. There are four settings. Press the right arrow to

increase the volume and left arrow to decrease the volume. You will see the volume

setting on the handset display. VOL 4 is the maximum and VOL 1 is the minimum.

Channel Button

While talking on the phone, you might need to manually change the channel in order

to reduce static caused by appliances, such as baby monitors, garage door openers,

microwave ovens, or other cordless phones. Press and release the CHAN/delete button

to move to the next clear channel.

Temporary Tone

This feature is useful only if you have pulse (rotary) service. Temporary Tone Dialing

enables pulse (rotary) service phone users to access touchtone services offered by

banks, credit card companies, etc. For example, when you call your bank you may need

to enter your bank account number. Temporarily switching to touchtone mode allows

you to send your number.

1. Dial the telephone number and wait for the line to connect.

2. When your call is answered, press the TONE*/exit button on the handset to

temporarily change from pulse dialing to tone dialing.

3. Follow the automated instructions to get the information you need.

4. Hang up the handset and the phone automatically returns to pulse (rotary) dialing

mode.

Exit

Press the TONE*/exit button to cancel any command you initiated.

Ringer Switch

The RINGER switch must be ON for the handset to ring during incoming calls.

Paging the Handset

This feature helps to locate a misplaced handset.

Press the page button on the base. The handset will beep for about two minutes or until

you press TALK/call back on the handset or press the page button on the base.

NOTE: You can still page the handset if the ringer is turned off. If the

battery is dead, the Paging feature will not work.

Caller ID (CID)

IMPORTANT: In order to use this unit’s Caller ID features, you must

subscribe to either the standard Name/Number Caller ID Service or

Call Waiting Caller ID Service. To know who is calling while you are

on the phone, you must subscribe to Call Waiting Caller ID Service.

This unit receives and displays information transmitted by your local phone company.

This information can include the phone number, date, and time; or the name, phone

number, date, and time.

2 Rights of the Telephone Company

Should your equipment cause trouble on your line which may harm the telephone network,

the telephone company shall, where practicable, notify you that temporary discontinuance of

service may be required. Where prior notice is not practicable and the circumstances warrant

such action, the telephone company may temporarily discontinue service immediately. In case

of such temporary discontinuance, the telephone company must: (1) promptly notify you of such

temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform

you of your right to bring a complaint to the Commission pursuant to procedures set forth in

Subpart E of Part 68, FCC Rules and Regulations.

The telephone company may make changes in its communications facilities, equipment,

operations or procedures where such action is required in the operation of its business and not

inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or

performance of your telephone equipment, the telephone company must give you adequate

notice, in writing, to allow you to maintain uninterrupted service.

Interference Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference; and (2) This device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is

“receiving” the interference).

• Reorient or relocate and increase the separation between the telecommunications

equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit different from that to

which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an experienced

radio/television technician for additional suggestions. Also, the Federal Communications

Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference

Problems.” This booklet is available from the U.S. Government Printing Ofce, Washington, D.C.

20402. Please specify stock number 004-000-00345-4 when ordering copies.

Hearing Aid Compatibility (HAC)

This telephone system meets FCC standards for Hearing Aid Compatibility.

Licensing

Licensed under US Patent 6,427,009.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body. This transmitter must not be co-located or

operated in conjunction with any other antenna or transmitter.”

ATLINKS USA, Inc.

10330 North Meridian Street

Indianapolis, IN 46290

Trademark(s) ® Registered

Marca(s) Registrada(s)

Model 27831

00008249 (Rev. 0 Dom E)

06-02

Printed in China

Modular

telephone

line jack

Wall plate

Base

Handset

Telephone

line cord

AC power

adaptor

Handset

battery pack

SE E MA RKI NG ON B OT TOM / B ACK OF PR OD UCT

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

CAUTION:

FORMAT/transfer

(button)

CID/VOL - or +

(button)

REDIAL

(button)

TALK/call back

(button)

FLASH/program

(button)

TONE*/exit

(button)

CHAN/delete

(button)

MEMORY

(button)

ringer/on-off

(switch)

PAUSE#

(button)

display

Call Waiting Caller ID

Provided you subscribe to Call Waiting Caller ID service from your phone company; if

you receive an incoming call and you are using the GE multi handset system, a beep

indicates the presence of a Call Waiting call on the line. The Call Waiting Caller ID

information will be displayed and stored in the history of all handsets in the system.

• When you hear the call waiting beep in the handset receiver, press the FLASH/

program button to put the current call on hold and answer the incoming call.

Press

FLASH/program again to return to the original call.

Receiving CID Records

When you receive a call, the Caller ID information is transmitted between the rst and

second ring. The Caller ID information appears on the display while the phone rings,

giving you a chance to monitor the information and decide whether or not to answer

the call.

Storing CID Records (In CID Memory)

If you are not at home or cannot answer, your telephone’s Caller ID memory stores the

data for the 40 most recent calls you received so you can see who called while you

were unavailable. When the 41st call is received, the oldest Caller ID record (1st call) is

automatically deleted.

You may review the stored information at any time. Calls received since your last

review show as in the display. Calls that have not been previously reviewed but NEW

were received from the same number more than once show as in the display.REPT

Time Date Number of calls

Caller ID

name

Caller ID phone

number

2. Plug one end of the telephone line cord into the TEL LINE jack on the bottom of the

base and the other end into a modular jack.

3. Plug the AC power converter into the electrical outlet and the DC connector into the

jack on the bottom of the base.

black wire

red wire

battery

pack

PRESS DOWN

FIRMLY

FORMAT

(button)

Model 27831xx2

Reviewing and Deleting Stored Numbers

1. To review stored numbers, press the

MEMORY

button, and use the CID/VOL ( - or + )

button to scroll to the memory location, or press the corresponding number key for a

desired memory location (0-9).

2. When the data shows in the display, press the CHAN/delete button. The display

shows DELETE? .

3. Press CHAN/delete again to delete the data. The display shows .DELETED

Dialing a Stored Number

1. Make sure the phone is by pressing the TALK/call back button.ON

2. Press the

MEMORY

button.

3. Press the memory location (0-9). The number dials automatically.

- OR -

1. Make sure the phone is (not in TALK mode).OFF

2. Press the

MEMORY

button.

3. Use the touch-tone pad or the CID/VOL ( - or + ) button to scroll to the number you

want to dial.

4. Press the TALK/call back button. The number dials automatically.

Chain Dialing from Memory

Use this feature to make calls which require a sequence of numbers, such as calling

card calls to a frequently called long distance number. Each part of the sequence is

dialed from memory. The following example shows you how to use chain dialing to

make a call through a long distance service:

The Number For Memory Location

Long distance access number 7

Authorization code 8

Frequently called long distance number 9

1. Make sure the phone is (in TALK mode).ON

2. Press the

MEMORY

button and then press 7.

3. When you hear the access tone, press the

MEMORY

button and then press 8.

4. At the next access tone, press the

MEMORY

button and then 9.

TIP: Wait for the access tones before pressing the next

MEMORY

button, or your call may not go through.

Changing the Battery

Make sure the telephone is (not in TALK mode) before you replace battery.OFF

1. Remove the battery compartment door.

2. Disconnect the cord attached to the battery pack and remove the battery pack from

the handset.

3. Insert the new battery pack and connect the cord to the jack inside the battery

compartment.

4. Put the battery compartment door back on.

5. Place handset in the base to charge. Allow the handset battery to properly charge

(for 16 hours) prior to ﬁrst use or when you install a new battery pack. If you do

not properly charge the phone, battery performance will be compromised.

CAUTION: To reduce the risk of ﬁre or personal injury, use only

the ATLINKS USA, Inc. Nickel-Cadmium battery model 5-2459,

which is compatible with this unit.

Battery Safety Precautions

• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type,

toxic materials could be released which can cause injury.

• To reduce the risk of re or personal injury, use only the

Nickel-Cadmium

battery

listed in the User’s Guide.

• Keep batteries out of the reach of children.

• Remove batteries if storing over 30 days.

Reviewing CID Records

As calls are received and stored, the display is updated to let you know how many calls

have been received. To scroll CID records:

1. Make sure the phone is (not in TALK mode).OFF

2. Press the CID/VOL (-) button to review the newest CID record.

3. Press the CID/VOL (+) button to review the oldest CID record rst.

Dialing a CID Number

1. Make sure the phone is (not in TALK mode). OFF

2. Use the CID/VOL ( - or + ) button to display the desired record.

3. Press the TALK/call back button. The number dials automatically.

NOTE: Depending on (a) how the incoming caller’s phone number is

formatted when it is received, and (b) whether or not you previously

pre-programmed your local area code into the set up menu, you

may need to adjust the format of the incoming caller’s stored phone

number before making the call, press the FORMAT button to adjust

the number, and try again

Available formats include:

Number of digits Explanation Example

Eleven digits long distance code “1 ” 1-317-888-8888

+3-digit area code

+7-digit telephone number.

Ten digits 3-digit area code + 317-888-8888

7-digit telephone number.

Seven digits 7-digit telephone number. 888-8888

Storing CID Records in Internal Memory

You may also store CID information in the phone’s internal memory.

NOTE:

It is important that you format CID records correctly BEFORE

storing in internal memory as you cannot reformat CID records

stored in memory.

1. Make sure the phone is (not in TALK mode).OFF

2. Use the CID/VOL (- or +) button to scroll to the desired CID record.

3. Press the MEMORY button.

4. Use the touch-tone pad to enter a memory location (0-9) to store the number in that

memory location. You will hear a conrmation tone.

NOTE: If the memory location is occupied, is REPLACE MEMO?

displayed, and you must conﬁrm replacement by pressing the

MEMORY button.

NOTE: Press the TONE*/exit button once to keep the previous setting

(making no changes) and return to the menu.

NOTE: If the selected CID record contains any information that is non-

numeric, the unit will not allow this record to transfer to the internal

user memory. The handset will display UNABLE TO STORE.

To Replace a Stored CID Record

1. Repeat steps 1 through 3 in Storing CID Records in Internal Memory. After you enter

the memory location, shows in the display.REPLACE MEMO?

2. Press the MEMORY button again, and the new CID record replaces the old memory in

that location. You will hear a conrmation tone.

Deleting a CID Record

1. Make sure the phone is (not in TALK mode).OFF

2. Use the CID/VOL ( - or + ) button to display the CID record you want to delete.

3. Press CHAN/delete. The display shows DELETE CALL ID?.

4. Press CHAN/delete again to erase the record and the next Caller ID record shows in

the display. You will hear a conrmation tone.

NOTE: Press the TONE*/exit key to return to the standby mode.

Deleting All CID Records

1. Make sure the phone is (not in TALK mode).OFF

2. Use the CID/VOL ( - or + ) button to display any Caller ID record.

3. Press and hold the CHAN/delete button until DELETE ALL? shows in the display.

4. Press CHAN/delete again to erase all records. You will hear a conrmation tone. The

display shows NO CALLS.

NOTE: Press the TONE*/exit key to return to the standby mode.

Memory

Each handset can store up to ten 24-digit numbers with up to 15-character names in

memory for quick dialing. This memory feature is in addition to the CID memory log,

which stores up to 40 CID records in each handset.

Storing a Name and Number in Memory

1. Make sure the phone is (not in TALK mode).OFF

2. Press the MEMORY button.

3. Press the desired memory location (0 through 9) or use CID/VOL ( + or - ) to scroll to

the desired memory location.

NOTE:

If the memory location is occupied, the memory location

number and stored name and telephone number shows in the

display. If the memory location is empty. shows in the display.EMPTY

4. Press the

MEMORY

button again. The display shows .ENTER NAME

NOTE: If you don’t want to enter the name, skip step 5.

5. Use the touch-tone pad on the handset to enter the name (up to 15 characters)

and press the memory button to save. More than one letter is stored in each of the

number keys. For example, to enter the name Bill Smith, press the 2 key twice for the

letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.

Wait for one second. Press the 5 key 3 times for the second letter L. Press the 1 key

to insert a space between the L and the S. Press the 7 key 4 times for the letter S;

press the 6 key once for the letter M; press the 4 key 3 times for the letter I; press the

8 key for the letter T; press the 4 key twice for the letter H.

NOTE: If you make a mistake press the DELETE/Channel button to

backspace and erase the wrong character(s) or number(s).

6. Press the

MEMORY

button to save the name. The display shows .ENTER TEL NUMBR

7. Use the touch-tone pad to enter the telephone number you want to store (up to

24 digits).

NOTE: The system treats PAUSES as delays or spaces in the dialing

sequence.

8. Press

MEMORY

again to store the number. You will hear a conrmation tone.

Storing the Last Number Dialed

1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.

2. Press the REDIAL button.

3. Press the

MEMORY

button to store the number. You will hear a conrmation tone.

To replace an old number with a new redial number:

1. Repeat steps 1 through 6 in Storing a Name and Number in Memory.

2. Press the REDIAL button.

3. Press the

MEMORY

button, and shows in the display.REPLACE MEMO?

4. Press the

MEMORY

button again to replace the old number with the new number.

You will hear a conrmation tone.

Inserting a Pause in the Dialing Sequence of a

Stored Number

If a pause is needed to wait for a dial or access tone, press the #PAUSE button to insert

a delay in dialing sequence of a stored number (for example, after you dial 9 for an

outside line, or to wait for a computer access tone). Pause shows in the display as a , P

and each pause counts as one digit in the dialing sequence.

Changing a Stored Number

1. Repeat steps 1 through 7 in Storing a Name and Number in Memory.

2. Press the

MEMORY

button, and shows in the display.REPLACE MEMO?

3. Press the

MEMORY

button to store the number. You will hear a conrmation tone.

Display Messages

The following indicators show the status of a message or of the unit.

BLOCKED CALL The person is calling from a number that has been

blocked from transmission.

BLOCKED NAME The persons name is blocked from transmission.

BLOCKED NUMBER The person is calling from a number that has been

blocked from transmission.

CALL WAITING Indicates a call is waiting on the line.

DELETE ALL? Prompt asking if you want to erase all Caller ID records.

DELETE CALL ID? Prompt asking if you want to erase a Caller ID record.

DELETED Prompt conrming the Caller ID record is erased.

EMPTY Indicates a memory location is vacant.

END OF LIST Indicates that there is no additional information in Caller

ID memory.

ENTER NAME Prompt telling you to enter the name for one of the 10

memory locations.

ENTER NUMBER Prompt telling you to enter the telephone number for one

of the 10 memory locations.

INCOMPLETE DATA Caller information has been interrupted during

transmission or the telephone line is excessively noisy.

LOW BATTERY Indicates the battery needs to be charged.

NEW Indicates call or calls have not been reviewed.

NO CALLS Indicates no calls have been received.

NO DATA No Caller ID information was received.

PAGING The PAGE button has been pressed on the base.

PRESS TALK KEY Indicates the CID number is a Direct Dial Number (DDN)

and cannot be formatted.

REPT Repeat call message. Indicates that a new call from the

same number was received more than once.

TRANSFERRING The handset is transferring a call or receiving notice to

accept a transferred call.

UNKNOWN NAME/ The incoming call is from an area not serviced by

CALLER/NUMBER Caller ID or the information was not sent.

Handset Sound Signals

Signal Meaning

A long warbling tone (with ringer on) Signals an incoming call

Three short beeps (several times) Page signal

Single beep every 7 seconds Low battery warning

Troubleshooting Guide

Caller ID Solutions

No Display

• The battery must be fully charged. Try replacing the battery.

• Make sure that the unit is connected to a non-switched electrical outlet. Disconnect

the unit from the wall and plug it in again.

• You must be subscribed to Caller ID service from your local telephone company in

order to receive Caller ID records.

Caller ID Error Message

• The unit displays this message if it detects anything other than valid Caller ID

information during the silent period after the rst ring. This message indicates either

the presence of noise on the line, or that an invalid message has been sent from the

telephone company.

NOTE: The RBRC seal on the battery used in

your ATLINKS USA, Inc. product indicates that

we are participating in a program to collect and

recycle Nickel Cadmium batteries throughout the

United States. Please call 1-800-8-BATTERY for

information or contact your local recycling center.

Cordless Phone Solutions

No dial tone

• Check installation:

Make sure the base power cord is connected to a working electrical outlet.

Make sure the telephone line cord is connected to the base unit and the wall phone

jack.

• Connect another phone to the same modular jack; if the second phone doesn’t work,

the problem might be with your wiring or local service.

• The handset may be out of range of the base. Move closer to the base.

• Make sure the battery is properly charged (for 16 hours).

• Ensure the battery pack is installed correctly.

• Did the handset beep when you pressed the TALK/call back button? Did the in use/

charge indicator come on? The battery may need to be charged.

• Place the handset in the base for at least 20 seconds.

Handset does not ring

• Make sure the RINGER switch on the handset is turned ON.

• Move closer to the base. The handset may be out of range.

• You may have too many extension phones on your line. Try unplugging some

phones.

• Check for a dial tone.

You experience static, noise, or fading in and out

• Change channels.

• Move closer to base. The handset might be out of range.

• Relocate the base. Make sure base is not plugged into an electrical outlet with

another household appliance.

• Charge the battery.

Unit beeps

• Place handset in base for 20 seconds; if it still beeps, charge battery for 16 hours.

• Clean the charging contacts on handset and base with a soft cloth.

• See solutions for “No dial tone.”

• Replace the battery.

Memory Dialing doesn’t work

• Make sure you programmed the memory location keys correctly.

• Did you follow proper dialing sequence?

Phone dials in pulse with tone service

• Make sure phone is in tone dialing mode.

Phone won’t dial out with pulse service

• Make sure phone is in pulse dialing mode.

Causes of Poor Reception

• Aluminum siding.

• Foil backing on insulation.

• Heating ducts and other metal construction that can shield radio signals.

• You’re too close to appliances such as microwaves, stoves, computers, etc.

• Atmospheric conditions, such as strong storms.

• Base is installed in the basement or lower oor of the house.

• Base is plugged into AC outlet with other electronic devices.

• Baby monitor is using the same frequency.

• Handset battery is low.

• You’re out of range of the base.

• Microwave oven is using the same frequency.

General Product Care

To keep your telephone working and looking good, follow these guidelines:

• Avoid putting the phone near heating appliances and devices that generate

electrical noise (for example, motors or uorescent lamps).

• DO NOT expose to direct sunlight or moisture.

• Avoid dropping the unit and other rough treatment.

• Clean with a soft cloth.

• Never use a strong cleaning agent or abrasive powder because this will damage the

nish.

• Retain the original packaging in case you need to ship the phone at a later date.

• Periodically clean the charge contacts on the handset and base with a soft cloth.

Service

If trouble is experienced with this equipment, for repair or warranty information, please

contact customer service at . If the equipment is causing harm to 1-800-448-0329

the telephone network, the telephone company may request that you disconnect the

equipment until the problem is resolved.

This product may be serviced only by the manufacturer or its authorized service

agents. Changes or modications not expressly approved by ATLINKS USA, Inc. could

void the user’s authority to operate this product. For instructions on how to obtain

service, refer to the warranty included in this guide or call customer service at 1-800-

448-0329.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the guide for future reference or jot down the date this

product was purchased or received as a gift. This information will be valuable if service

should be required during the warranty period.

Purchase date ______________________________________________________

Name of store ______________________________________________________

Limited Warranty

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year, from date of purchase.

(The warranty period for rental units begins with the rst rental or 45 days from date

of shipment to the rental rm, whichever comes rst.)

What we will do:

• Provide you with a new or, at our option, a refurbished unit. The exchange unit is

under warranty for the remainder of the original product’s warranty period.

How you get service:

• Properly pack your unit. Include any cables, etc., which were originally provided with

the product. We recommend using the original carton and packing materials.

• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence

that the product is within the warranty period, must be presented to obtain warranty

service.” For rental rms, proof of rst rental is also required. Also print your name

and address and a description of the defect. Send via standard UPS or its equivalent

to:

ATLINKS USA, Inc.

c/o Thomson Inc.

11721 B Alameda Ave.

Socorro, Texas 79927

• Pay any charges billed to you by the Exchange Center for service not covered by the

warranty.

• Insure your shipment for loss or damage. ATLINKS accepts no liability in case of

damage or loss.

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty cover:does not

• Customer instruction. (Your Owner’s Manual provides information regarding

operating instructions and user controls. Any additional information, should be

obtained from your dealer.)

• Installation and setup service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modied or incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed with your unit. It will

make it easier to contact you should it ever be necessary. The return of the card is

not required for warranty coverage.

Limitation of Warranty:

• The warranty stated above is the only warranty applicable to this product. All other

warranties, express or implied (including all implied warranties of merchantability

or tness for a particular purpose) are hereby disclaimed. No verbal or written

information given by ATLINKS USA, Inc., its agents, or employees shall create a

guaranty or in any way increase the scope of this warranty.

• Repair or replacement as provided under this warranty is the exclusive remedy of

the consumer. ATLINKS USA, Inc. shall not be liable for incidental or consequential

damages resulting from the use of this product or arising out of any breach of any

express or implied warranty on this product. This disclaimer of warranties and

limited warranty are governed by the laws of the state of Indiana. Except to the

extent prohibited by applicable law, any implied warranty of merchantability or

tness for a particular purpose on this product is limited to the applicable warranty

period set forth above.

How state law relates to this warranty:

• Some states do not allow the exclusion nor limitation of incidental or consequential

damages, or limitations on how long an implied warranty lasts so the above

limitations or exclusions may not apply to you.

• This warranty gives you specic legal rights, and you also may have other rights that

vary from state to state.

If you purchased your product outside the USA:

• This warranty does not apply. Contact your dealer for warranty information.

Accessory Information

To place order, have your Visa, MasterCard, or Discover Card ready

and call toll-free .1-800-338-0376

A shipping and handling fee will be charged upon ordering.

We are required by law to collect appropriate sales tax for each individual state, country,

and locality to which the merchandise is being sent.

Items are subject to availability.

*Prices are subject to change without notice.

DESCRIPTION MODEL NO.

AC Power adaptor/black 5-2616

AC Power adaptor/gray 5-2617

Handset Replacement Battery 5-2459

Product specificaties

Merk:	GE
Categorie:	Telefoon
Model:	27831

Heb je hulp nodig?

Als je hulp nodig hebt met GE 27831 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Telefoon GE

21 Juni 2023

6 April 2023

1 April 2023

17 Maart 2023

17 Januari 2023

Handleiding Telefoon

Nieuwste handleidingen voor Telefoon

EMeet OfficeCore M2 Handleiding

19 November 2024

Geemarc Serenties Handleiding

17 November 2024

Auerswald COMpact 4000 Handleiding

17 November 2024

Auerswald COMfortel 1200 Handleiding

17 November 2024

Akuvox MD12 Handleiding

17 November 2024

MyPhone Metro+ Handleiding

16 November 2024

Ranex RX 6023 Handleiding

16 November 2024

SPC AIR Handleiding

16 November 2024

Pixel M80 Handleiding

16 November 2024

Pixel Voical Air 2 Handleiding

16 November 2024