Garmin VIRB Remote Handleiding

Garmin Afstandsbediening VIRB Remote

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin VIRB Remote (14 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/14
VIRB™ Remote Instructions.............................................................................................................. 2
Instructions de la télécommande VIRB™.......................................................................................... 4
VIRB™ Istruzioni del telecomando.................................................................................................... 6
VIRB™ Fernbedienung – Anweisungen............................................................................................ 8
VIRB™ Instrucciones del mando a distancia................................................................................... 10
Instruções do controlo remoto VIRB™............................................................................................ 12
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. VIRB™ and ANT+™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
This product is ANT+™ certified. Visit for a list of compatible products and apps.www.thisisant.com/directory
July 2014 190-01627-90_0DPrinted in Taiwan
TA-2013/2179
TRA
REGISTERED No:
ER0127480/14
DEALER No:
DA0061884/11
VIRB™ Remote Instructions
Remote Overview
ÀRecord key. Select to record video on connected devices.
ÁPhoto key. Select to capture a photo on connected devices.
ÂStop key. Select to stop recording video on connected devices.
ÃStatus LED.
Status LED
LED Activity Status
Flashing green Searching for a paired device.
Alternating red and green Attempting to pair with a device.
12 rapid green flashes Successfully paired with a device.
Four rapid green flashes Successfully sent a command to a device.
Four rapid red flashes Failed to send a command to a device.
Flashing red Device is recording video.
Pairing the Remote with Your Device
The first time you connect the VIRB remote to your VIRB
device, you must pair the remote with your device.
1On the VIRB device, select > > to SETUP Remote Remote
turn on the remote control feature.
2On the VIRB remote, select any key.
The status LED starts flashing green.
3On the VIRB remote, hold two keys simultaneously until the
status LED starts alternating green and red, and release the
keys.
The remote searches for your VIRB device. When the
remote pairs successfully, the status LED flashes green 12
times.
After the remote is paired, it connects to your device whenever
the device is in range and turned on.
Using the Mounts
Several mounts are available for your remote, either included
with the product or as an optional accessory. The mounts allow
you to attach the remote to your body, your bike, or other
objects.
• Align two of the notches À with the sides of the mount, and
press the remote into the mount until it clicks.
• Press gently on the release tab Á, and lift the remote from
the mount.
Replacing the Battery
WARNING
Do not use a sharp object to remove batteries.
Keep the battery away from children.
Never put batteries in mouth. If swallowed, contact your
physician or local poison control center.
Replaceable coin cell batteries may contain perchlorate
material. Special handling may apply. See
www.dtsc.ca.gov.hazardouswaste/perchlorate.
CAUTION
Contact your local waste disposal department to properly
recycle the batteries.
Before you can replace the battery, you must have a small
Phillips screwdriver, a small flat screwdriver, and a CR2032
lithium coin-cell battery.
1Using a Phillips screwdriver, remove the three screws from
the back plate À.
2Remove the back plate from the remote.
3Wrap the end of a small flat screwdriver with tape.
The tape protects the battery, battery compartment, and
contacts from damage.
4Carefully pry the battery from the back plate.
5Install the new battery into the back plate with the positive
side facing down.
6Verify the gasket Á is fully seated in the groove.
2
7Replace the backplate, aligning the post  with the gap in
the circuit board Ã.
8Replace and tighten the three screws.
NOTE: Do not overtighten.
Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Up to 1.5 years (1 hour per day)
Operating temperature
range
From -10° to 50°C (from 14° to 122°F)
Radio frequency/protocol 2.4 GHz ANT+™ wireless communications
protocol
Water rating 5 ATM*
*The device withstands pressure equivalent to a depth of
50 meters.
3

Product specificaties

Merk: Garmin
Categorie: Afstandsbediening
Model: VIRB Remote

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin VIRB Remote stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Afstandsbediening Garmin

Garmin

Garmin GHS 20 Handleiding

29 Maart 2023
Garmin

Garmin eBike Remote Handleiding

14 Februari 2023
Garmin

Garmin VIRB Remote Handleiding

12 Februari 2023
Garmin

Garmin GHS 20i Handleiding

15 Oktober 2022

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening

Nanlite

Nanlite BT-BCS-48V3.5mm Handleiding

21 December 2024
One For All

One For All Essence 4 KE1242 Handleiding

13 December 2024
Genaray

Genaray RSF-11-R Handleiding

12 December 2024
Genaray

Genaray ML-LSR Handleiding

12 December 2024
Genaray

Genaray MonoBright MB-WRT Handleiding

12 December 2024
Futaba

Futaba SBS-01V Handleiding

10 December 2024
Futaba

Futaba T3PV Handleiding

10 December 2024
Futaba

Futaba DLPH-1 Handleiding

10 December 2024
Audio-Technica

Audio-Technica AT-SL931HD Handleiding

6 December 2024
Velleman

Velleman DVRRC4 Handleiding

3 December 2024