Garmin Upland Handleiding

Garmin Niet gecategoriseerd Upland

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin Upland (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 278 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
Beeper Instructions............................................................................................................................2
Instructions relatives au bipeur.......................................................................................................... 4
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Delta™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not
be used without the express permission of Garmin.
June 2014 190-01630-03_0A Printed in Taiwan
Beeper Instructions
Beeper Device Overview
ÀBattery cover
ÁPower key
ÂSpeaker
ÃStatus LEDs
Putting the Beeper Device on Your Dog
You should install the beeper device onto the same collar strap
with a compatible dog device, such as a Delta Upland™ device
or a Garmin Pro series device.
1Insert the end of the collar strap through the slot at the base
of the beeper device.
2Place the collar on the dog's neck, and position the beeper
device at the back of the dog's neck.
Turning the Beeper Device On and Off
• Hold the power key until the red status LED flashes once to
turn on the device.
• Hold the power key until red status LED turns off, and then
release the power key immediately to turn off the device.
Beeper Sounds
The beeper device can emit two sounds: a beep and a hawk scream. These sounds indicate your dog's hunting and pointing status.
While your dog is hunting, the beeper device emits a series of one to three beeps every four seconds. You can select the number of
beeps in the series, which is useful to distinguish between multiple dogs. You can also disable this sound so that the beeper device
is silent while your dog is hunting.
When your dog is pointing, the beeper emits either one beep every second or one hawk scream every five seconds, depending on
the setting you choose.
When you select beeper sounds, the selected sounds are indicated briefly by the status LEDs. The red status LED indicates the
hunting sound, and the green status LED indicates the pointing sound.
Mode Red LED Hunting Sound Green LED Pointing Sound
1 1 blink 1 beep Solid Hawk scream
2 2 blinks 2 beeps
3 3 blinks 3 beeps
4 Off Silent
5 1 blink 1 beep Blinking Beep
6 2 blinks 2 beeps
7 3 blinks 3 beeps
8 Off Silent
Customizing the Beeper Sounds
1With the device turned on, hold the power key until both
LEDs blink rapidly three times, and release the power key.
2Select the power key to cycle through the sound modes.
Each time you select the power key, the LEDs indicate the
selected sound mode. You may have to cycle through
several sound modes to reach your preferred sound mode.
3Hold the power key until both LEDs blink rapidly three times,
and release the power key to set the sound mode to the
current selection.
Resetting to the Default Beeper Sounds
You can reset your beeper device to the factory default sound
settings, regardless of the current setting or power state of the
device.
Hold the power key for 15 seconds.
The device emits a high-low, high-low beep sequence, and
the LEDs flash to confirm the reset.
The next time you turn on the device, it is set to mode 1.
Turning the Beeper Sounds On or Off Remotely
Before you can turn the beeper sounds on or off remotely, the
dog collar device and the beeper device must be turned on.
You can use the handheld device to turn the beeper sounds on
or off remotely. Turning off the beeper sounds does not turn off
the beeper device.
1On the handheld device, select a training mode in which a
training key is assigned to the beeper device.
2Select the training key assigned to the beeper device to turn
the beeper sounds on or off for the selected dog.
Replacing the Beeper Battery
Before you can replace the battery, you must have a Phillips-
head screwdriver and a CR123A lithium battery.
1Using a Phillips-head screwdriver, remove the screw À from
the battery cover Á.
2
2Remove the battery cover and battery
Â.
3Insert the new battery, observing polarity.
4Verify the gasket à is fully seated in the groove.
5Replace the battery cover and screw.
Beeper Device Specifications
Battery type CR123A lithium
Battery life Up to 100 hours run time
Operating temperature range -4° to 110°F (-20° to 43°C)
Water resistance IEC 60529 IPX7
3

Product specificaties

Merk: Garmin
Categorie: Niet gecategoriseerd
Model: Upland

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin Upland stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Garmin

Garmin

Garmin dēzl Headset 210 Handleiding

13 November 2024
Garmin

Garmin Edge Power Mount Handleiding

2 Oktober 2024
Garmin

Garmin Approach Z30 Handleiding

23 Juli 2024
Garmin

Garmin Tacx NEO 3M Handleiding

25 Juni 2024
Garmin

Garmin Delta SE Handleiding

9 Juli 2023
Garmin

Garmin Foretrex 801 Handleiding

8 Juli 2023
Garmin

Garmin BMW Motorrad Navigator VI Handleiding

19 Juni 2023
Garmin

Garmin GSD 26 Handleiding

18 Juni 2023
Garmin

Garmin Dash Cam 54 Handleiding

15 Juni 2023
Garmin

Garmin Varia ERTL615 Handleiding

6 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024
Kolcraft

Kolcraft MLB New York Yankees Handleiding

26 November 2024
Kolcraft

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024
Kolcraft

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024
Nedis

Nedis POCO106 Handleiding

26 November 2024
Nedis

Nedis BTSM1GY Handleiding

26 November 2024
Turbosound

Turbosound TPOLEAJ-01 Handleiding

26 November 2024
Turbosound

Turbosound TSTAND-01 Handleiding

26 November 2024
IFM

IFM TAD981 Handleiding

26 November 2024
IFM

IFM TAD961 Handleiding

26 November 2024