Garmin Spectra LC102 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin Spectra LC102 (13 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/13
GARMIN SPECTRA â„¢ LED MODULE CONTROL
INSTALLATION INSTRUCTIONS
Important Safety Information
Important Safety Information
Important Safety Information
Important Safety InformationImportant Safety Information
WARNING
See the guide in the product box for product warnings and other Important Safety and Product Information
important information.
Failure to install this device according to these instructions could result in personal injury, damage to the vessel
or device, or poor product performance.
CAUTION
To avoid possible personal injury or damage to the device and vessel, disconnect the vessel's power supply
before beginning to install the device.
To avoid possible personal injury, always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging the vessel.
You must read all installation instructions before beginning the installation. If you experience difficulty during
the installation, go to .
support.garmin.com
Tools and Supplies Needed
Tools and Supplies Needed
Tools and Supplies Needed
Tools and Supplies NeededTools and Supplies Needed
• 16AWG (1.3mm2) wire to connect the wiring harness to power
• Inline fuse apporpriately-rated for the power source and connected LEDs ( ).
Connecting to Power, page4
• 20AWG (0.5mm2) wire to connect the wiring harness to lighting
You can purchase marine LED cable from your Fusion® or Garmin® dealer in 100m (328ft.) lengths
(010-13386-00).
• #2 Phillips screwdriver
• Appropriately sized marine-grade connectors for connecting the wiring harnesses to the speaker wire
• Wire cutters
• Drill and 2 mm (3/32in.) drill bit for mounting the LED control module
Getting Started
Getting Started
Getting Started
Getting StartedGetting Started
The Garmin Spectra LED control module allows you to control connected LED lights using compatible Garmin
chartplotters and compatible Fusion stereos connected to the same NMEA 2000® network. You can also control
connected LED lights using the ActiveCaptain® app.
The Garmin Spectra LED control module is designed for controlling only LED lighting. You must not use this
device to control navigation lights, non-LED lighting, or other devices.
This manual contains instructions for installing and performing the initial configuration for the Garmin Spectra
LED control module using a Garmin chartplotter or ActiveCaptain app. For complete instructions on using the
Garmin Spectra LED control module with a connected chartplotter or Fusion stereo, see the latest chartplotter or
stereo owner's manual.
GUID-6A3E1D9B-1E17-4069-BF5C-3C82F2202A9B v2September 2024
Downloading the Latest Chartplotter or Stereo Owner's Manual
Downloading the Latest Chartplotter or Stereo Owner's Manual
Downloading the Latest Chartplotter or Stereo Owner's Manual
Downloading the Latest Chartplotter or Stereo Owner's ManualDownloading the Latest Chartplotter or Stereo Owner's Manual
For complete operating and customization instructions for the LED lighting features, download the latest
version of the owner's manual for your chartplotter or stereo from the Garmin website.
1 Go to or scan this QR code.
garmin.com/manuals/
2 Enter the name of your chartplotter or stereo and select the appropriate model
from the results.
3 Owner's ManualSelect on the manuals page.
Mounting Considerations
Mounting Considerations
Mounting Considerations
Mounting ConsiderationsMounting Considerations
Selecting the correct mounting location is critical to optimize the performance of the Garmin Spectra LED
control module. When selecting a mounting location, observe these considerations.
• You should mount the device in an accessible location.
• You should not mount the device near fuel tanks or bilge areas where combustible fumes may accumulate.
• You should mount the device in a location with access to a common ground for other electronics.
• When controlling LED speakers, the controller should be mounted within 5M (16ft. 4in.) of the speakers.
• You must mount the device in a location where it is not submerged.
• You should mount the device on a flat, vertical mounting surface, with the wire harness connectors pointing
down.
• You should clear the mounting surface of dirt, debris, wax, or coatings.
• You should select a location away from sources that can interfere with the device's operation. Sources of
interference may include strong electromagnetic fields, such as power cables and electric motors.
Mounting the Device
Mounting the Device
Mounting the Device
Mounting the DeviceMounting the Device
Before you can mount the device, you must select a location in accordance with the mounting considerations.
You must use the included mounting screws or acquire pan-head screws of the appropriate length for the
mounting surface.
NOTICE
Do not use the Garmin Spectra LED control module as a template when drilling the mounting holes. Drilling
through the mounting holes may damage the device and void the warranty.
Do not apply grease or lubricant to the screws when fastening the device to the mounting surface. Grease or
other lubricants can cause damage to the device housing.
You must use pan-head screws to secure the device. Using countersunk screws can damage the device
housing.
1 With the wiring-harness connectors pointing down, hold the device on a flat, vertical mounting surface and
mark the locations for the pilot holes.
2 Remove the device from the mounting surface.
3 Using a 2mm (3/32 in.) drill bit, drill the pilot holes.
4 Fasten the included pan-head screws into the pilot holes.
5 Secure the device to the mounting surface by tightening the screws until they are snug.
NOTICE
Do not overtighten the screws because it may damage the device housing.
2
Connection Considerations
Connection Considerations
Connection Considerations
Connection ConsiderationsConnection Considerations
You should carefully plan the layout of the device, the power wiring, the NMEA 2000 network, and all LED
lighting devices before making any connections. This is a connection overview. See the relevant connection
sections for more information on particular connections.
Garmin Spectra LED Control Module
LED wiring harness
Power wiring harness
NMEA 2000 cable
Momentary switch (optional)
Appropriately rated slow-blow fuse (not included)
Ignition or ACC switch (recommended)
12 or 24Vdc LED lighting (LED speaker in this example)
12 or 24Vdc power source
When making connections, observe these considerations.
• This device supports a maximum of 2 A per LED wiring harness. When planning lighting connections,
consider the power needs of all potential load combinations to ensure that the total active load does not
exceed 2 A per LED wiring harness when in use.
• You must connect all lighting to a common ground.
• You must make all bare wire connections using appropriately sized marine-grade, waterproof connectors or
waterproof heat-shrink.
• You must insulate any unused bare wire connections after completing installation.
• When extending wires, you must use the appropriate wire gauge for the individual wires on the wiring
harnesses.
• To avoid interference, avoid bundling or routing speaker and LED wires together.
3


Product specificaties

Merk: Garmin
Categorie: Niet gecategoriseerd
Model: Spectra LC102

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin Spectra LC102 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Garmin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd