Garmin GXM 51 Handleiding

Garmin Niet gecategoriseerd GXM 51

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin GXM 51 (15 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 263 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/15

GXM™ 51 Installation Instructions

The Garmin GXM 51 XM

antenna provides XM WX Satellite Weather

information and XM

Satellite Radio

for your existing NMEA 2000

network. If you do not have an existing NMEA

2000 network on your boat, you will need to install one. For more information about NMEA

2000, visit www.garmin.com.

The GXM 51 antenna must be properly installed according to the following instructions.

You need the appropriate fasteners, tools, and mounts listed in each section. These items

are available at most marine dealers. Always wear safety goggles, ear protection, and a dust

mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the

opposite side of the surface.

Contact Garmin Product Support if you have any questions while installing or using your

GXM 51. In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at

(913) 397-8200 or (800) 800-1020.

See the Important Safety and Product Information guide in the product box for product warnings and other

important information.

Product Registration

Help us better support you by completing our online registration at www.garmin.com

/registration/.

For future reference, write the serial number assigned to your GXM 51 in the space provided. It

is located on a sticker on the back of the device.

Serial number

In addition to the device serial number, unique ID numbers are associated with your GXM 51.

XM Satellite Radio uses these ID numbers to activate and deactivate your XM weather and

XM audio. To locate the ID numbers on a Garmin NMEA 2000-compliant chartplotter, select

Congure System System Information > > .

For future reference, write the XM WX Weather ID and XM Radio ID assigned to your

GXM 51 in the spaces provided.

XM WX Weather ID

XM Radio ID

November 2009 190-01030-02 Rev. D Printed in Taiwan

2GXM 51 Installation Instructions

Packing List, Accessories, and Tools Needed

Before installing your unit, conrm that your package includes the following items. If any parts

are missing, contact your Garmin dealer immediately.

Standard Package

GXM 51 Antenna

Surface-mount bracket

Pole-mount bracket

Under-deck mount bracket

Mounting hardware (screws and adhesive

pads)

NMEA 2000 T-connector

NMEA 2000/audio cable 19 ft., 8 in. (6 m)

Audio adapter cable 1 ft. (30.5 cm)

Installation instructions

Optional Accessories

Additional NMEA 2000 network

components

Audio adapter cable extensions

•

Tools Needed

Drill

Drill bits—

in. (3 mm) and

in.

(19 mm)

Hole saw, 1 in. (25 mm)—surface-mount

cable hole

Screwdriver—surface-mount screws

Pencil (to mark surface-mount pilot holes)

Countersink bit (when mounting on

berglass)

Marine sealant (for some mounting

options)

•

Step 1: Mount the GXM 51 Antenna

You can surface mount the GXM 51 antenna, attach it to a standard 1 in. OD pipe-threaded-pole

marine mount (14 threads-per-inch—not included), or even install the antenna under berglass.

Select a suitable location for the GXM 51

antenna on your boat. To ensure the best

reception, mount the GXM 51 antenna in a

location that has a clear, unobstructed view of

the sky in all directions.

Avoid mounting the GXM 51 antenna

where it is shaded by the superstructure of

the boat, a radome antenna, or a mast.

On a sailboat, avoid mounting the GXM 51

antenna high on the mast.

The GXM 51 antenna provides more-stable

reception when located nearer to water

level.

Mount the GXM 51 antenna at least 3.3 ft. (1 m) away from (preferably above) the

path of any radar beam or a VHF radio antenna.

Temporarily secure the antenna in the preferred mounting location and test it for correct

operation. If you experience interference with other electronics, try a different location. After

verifying correct operation, permanently mount the antenna.

•

SS BARNETT

Radar VHF Radio Antenna

3 ft.

(1 m)

Above - best

Below - OK

EMI (Electromagnetic Interference)

from engine components

Best

Better

Good

EMI

GXM 51 Placement Considerations

SS BARNETT

Radar VHF Radio Antenna

3 ft.

(1 m)

Above - best

Below - OK

EMI (Electromagnetic Interference)

from engine components

Best

Better

Good

EMI

GXM 51 Placement Considerations

GXM 51 Installation Instructions 3

Surface-mounting the GXM 51 Antenna

1. Use the surface-mount bracket as your mounting template.

Use a pencil to mark the three screw locations on the surface and to trace the cable hole

in the center of the bracket.

Set the surface-mount bracket aside. Do not drill through the surface-mount bracket.

2. Drill three 1/8 in. (3 mm) pilot holes.

Note: If you are mounting the GXM 51 on berglass, it is recommended to use a countersink

bit to drill a clearance counterbore through the top gelcoat layer (but no deeper). This will help to

avoid cracking in the gelcoat layer when the screws are tightened.

3. Use a 1 in. (25 mm) hole saw to cut the cable hole in the center.

4. Use the included M4 screws to attach

the surface-mount bracket to the

mounting surface.

5. Route the NMEA 2000/audio cable

through the 1 in. (25 mm) cable hole

and connect it to the GXM 51.

6. Make sure the large gasket is in

place on the bottom of the GXM 51

antenna, place the antenna on the

surface-mount bracket , and twist it ➊

clockwise to lock it in place .➋

7. Secure the antenna to the mounting

bracket with the included M3 set

screw .➌

8. Route the NMEA 2000/audio cable

away from sources of electronic interference, and connect it to your NMEA 2000 network

and to the audio input of your stereo receiver (see ).page 5

Pole Mounting the GXM 51 Antenna

With the pole-mount adapter attached to the GXM 51, you can install the GXM 51 on a

standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not included). You

can route the NMEA 2000/audio cable either through the pole or outside the pole.

To mount the GXM 51 with the cable routed outside the pole:

1. Route the NMEA 2000/audio cable through the pole-mount adapter, and place the cable in

the vertical slot along the base of the pole-mount adapter.

2. Thread the pole-mount adapter onto a standard 1 in. OD pipe-threaded-pole marine mount

(14 threads per inch—not included). Do not overtighten the adapter.

3. Connect the NMEA 2000/audio cable to the

GXM 51 antenna.

4. Place the GXM 51 antenna on the pole-mount

adapter and twist it clockwise to lock it in ➊

place .➋

5. Secure the antenna to the adapter with the

included M3 set screw .➌

6. (Optional) With the GXM 51 installed on the

pole mount, ll the remaining gap in the vertical

cable slot with a marine sealant (not included).

7. Attach the marine mount to the boat if it is not

already attached.

8. Route the NMEA 2000/audio cable away from

sources of electronic interference, and connect

it to your NMEA 2000 network and to the audio

input of your stereo receiver (see ).page 5

•

GXM 51

antenna

Surface-mount

bracket

Mounting

surface

➊

➋

➌

Rubber

gasket

GXM 51

antenna

Surface-mount

bracket

Mounting

surface

➊

➋

➌

Rubber

gasket

GXM 51

antenna

Pole-mount

adapter

Vertical cable

slot

➊

➋

➌

GXM 51

antenna

Pole-mount

adapter

Vertical cable

slot

➊

➋

➌

Product specificaties

Merk:	Garmin
Categorie:	Niet gecategoriseerd
Model:	GXM 51
Kleur van het product:	Wit
Gewicht:	201 g
Snoerlengte:	6 m
Stroomvoorziening:	9 –16VDC, 137mA
Certificering:	IEC 529 IPX7
Interface:	NMEA 2000
Compatibiliteit:	GPSMAP
Aansluiting(en):	NMEA 2000-T
Afmetingen (B x D x H):	91.6 x 91.6 x 49.5 mm