Garmin GTX 320A Handleiding

Garmin Niet gecategoriseerd GTX 320A

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin GTX 320A (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

G T X 3 2 0

T R A N S P O N D E R

P i l o t ’ s

G u i d e

Operating The GTX 320

The GTX 320 owner accepts all responsibility for obtaining the proper license before

using the transponder.

The coverage you can expect from the GTX 320 is limited to “line of sight”. Low altitude

or aircraft antenna shielding by the aircraft itself may result in reduced range. Range can

be improved by climbing to a higher altitude. It may be possible to minimize antenna

shielding by locating the antenna where dead spots are only noticed during abnormal

flight attitudes.

Function Selector Switch

The function selector switch is a five position rotary switch. The five positions are:

• OFF—Turns off all power to the GTX 320 (the GTX 320 should be turned off before starting

aircraft engine(s).

• SBY—Turns the transponder on, but when in SBY the GTX 320 will not reply to any interro-

gations from the ground radar system.

• —Places the transponder in Mode A, the identification mode. In addition to the aircraft’sON

identification code, the GTX 320 will also reply to altitude interrogations (Mode C) with sig-

nals that do not contain altitude information.

• ALT—Activates all of the necessary circuitry (transponder to optional altitude digitizer and

return) to respond to ATC altitude interrogations and aircraft identification interrogations with

standard pressure altitude (29.92 inches Hg). The ALT position may be used in aircraft that

are not equipped with the optional altitude digitizer, however, the only response will be dis-

creet signals that do not contain altitude information.

• TST—Turning the switch to the TST position tests the reply indicator. The TST position is

spring loaded and must be held momentarily. When released, it will automatically return to

the ALT position.

NOTES

IDENT BUTTON

FUNCTION SELECTION KNOB

REPLY LIGHT

CODE SELECTION KNOBS

Any time the function switch is in the ON or ALT position the transponder becomes an active part

of the beacon system. Select ON or ALT as late as practical prior to takeoff and switch to OFF or SBY

as soon as practical after completing landing roll unless the change to SBY has been accomplished

previously at the request of ATC.

Code Selector

The code selector consists of four, eight position switches that provide 4,096 active identification

codes. Attention should be paid to the selected identification code. The selected code should be in

accordance with instructions for IFR flight or rules applicable to transponder utilization for VFR

flight.

When making routine code changes, you should avoid inadvertent selection of codes 7500, 7600,

or 7700 thereby causing momentary false alarms at automated ground facilities. For example when

switching from code 2700 to code 7200, switch first to 2200 then 7200, NOT to 7700 and then

7200.

This procedure applies to nondiscrete code 7500 and all discrete codes in the 7600 and 7700 series

(i.e., 7600-7677, 7700-7777) which trigger special indicators in automated facilities. Only nondis-

crete code 7500 will be decoded as the hijack code. An aircraft’s transponder code (when available)

is utilized to enhance the tracking capabilities of the ATC facility, therefore you should not turn the

GTX 320 to SBY when making routine code changes.

Important Codes

• 1200—The VFR Code for any altitude.

• 7600—Loss of Communications.

• 7500—Hijacking (Never assigned by ATC without prior notification of the pilot that his or

her aircraft is subject to unlawful interference).

• 7700—Emergency (All secondary surveillance radar sites are ready to receive this code at all

times).

See the Airman’s Information Manual (AIM) for a detailed explanation of identification codes.

IDENT Button

On occasion, the controller will request “SQUAWK IDENT”. Respond by momentarily pressing and

releasing the IDENT button. Pressing the IDENT button activates the Special Position Identification

Pulse (SPI) for approximately 20 seconds identifying your transponder return from other aircraft on

the controller’s scope.

Reply Light

The reply light will blink each time the transponder replies to ground interrogation. The reply light

remains lit up during the IDENT time interval.

Product specificaties

Merk:	Garmin
Categorie:	Niet gecategoriseerd
Model:	GTX 320A

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin GTX 320A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Garmin

Garmin dēzl Headset 210 Handleiding

13 November 2024

Garmin Edge Power Mount Handleiding

2 Oktober 2024

Garmin Approach Z30 Handleiding

23 Juli 2024

Garmin Tacx NEO 3M Handleiding

25 Juni 2024

Garmin Delta SE Handleiding

9 Juli 2023

Garmin Foretrex 801 Handleiding

8 Juli 2023

Garmin BMW Motorrad Navigator VI Handleiding

19 Juni 2023

Garmin GSD 26 Handleiding

18 Juni 2023

Garmin Dash Cam 54 Handleiding

15 Juni 2023

Garmin Varia ERTL615 Handleiding

6 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024

Bosch KSZ2AVU00 Handleiding

22 November 2024