Garmin GET 10 Handleiding

Garmin Niet gecategoriseerd GET 10

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin GET 10 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 223 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
GET™ 10 Installation and Conguration Instructions
Use the Garmin
®
GET 10 adapter to adapt analog information provided by an engine-tilt sensor
on your boat to your NMEA 2000
®
network. Your GET 10 adapter allows you to observe
engine-tilt information on compatible Garmin display devices connected to your NMEA 2000
network. For a list of compatible Garmin chartplotters and devices, visit www.garmin.com.
Compare the contents of this package with the packing list on the box. If any pieces are
missing, contact your Garmin dealer immediately.
Product Registration
Help us better support you by completing our online registration today. Go to http://my.garmin
.com. Keep the original sales receipt, or a photocopy, in a safe place.
Contact Garmin
Contact Garmin Product Support if you have any questions while using your GET 10. In the
USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or
(800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to www.garmin.com/support and click for in-country support Contact Support
information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.
See the Important Safety and Product Information guide in the compatible Garmin display device box for
product warnings and other important information..
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or CAUTION:
sanding.
When drilling or cutting, always check the opposite side of the drilling or cutting NOTICE:
surface.
Needed Tools and Supplies
Heat-shrink tubing and a heat gun
Cable ties
Additional NMEA 2000 cabling and connectors (optional)
•
•
•
July 2009 190-01081-05 Rev. A Printed in Taiwan
 GET10InstallationandCongurationInstructions
Determining an Installation Location
When you are selecting a location to install the GET 10 adapter, consider the following:
During installation, you connect the GET 10 adapter to the analog gauge (or directly to the
engine-tilt sensor), and to the NMEA 2000 network. Therefore:
Choose a location that is within 173 in. (4.4 m) of the analog gauge (or the engine-tilt
sensor) to avoid splicing bare wires.
Choose a location between the NMEA 2000 backbone and the analog gauge (or the
engine-tilt sensor).
If you cannot connect the adapter directly to the NMEA 2000 network, add a drop cable.
See for more information.page 3
The adapter is IEC 60529 IPX7 waterproof, and can be submerged up to 30 minutes at
1 meter. Do not install the adapter in a location where it will be submerged regularly, though
the location can be subject to wash-down.
You can use cable ties (not included) to secure the adapter to an existing structure on your
boat.
You can use mounted-head cable ties (not included) and screws (not included) to secure the
adapter to a bulkhead or other suitable surface on your boat.
Install the adapter at least 2 in. (5 cm) from a magnetic compass to prevent electromagnetic
interference, which can cause inaccurate compass readings.
Wiring the GET 10
Connect the GET 10 adapter either to an analog gauge or to the sender directly using the bare
wires on the wiring harness.
Wiring the GET 10 Adapter to an Analog Gauge
If your boat has an analog gauge representing engine tilt, you can wire the GET 10 adapter
directly to the gauge. Consult the owner’s manual provided by your boat or sensor manufacturer
to determine the ground, sensor, and power (ignition) connections on the gauge. Typically,
the power (ignition) connector is labeled with a “+”, a “+12V”, an “I”, or an “IGN” marking.
The ground connector is typically labeled with a “-”, a “ ”, or a “G” marking, and the sensor
connector is typically labeled with an “S” or a “G” marking. Do not remove any wires from the
back of the gauge, and wire the GET 10 adapter to the gauge using the following table.
Wiring the GET 10 Adapter Directly to an Engine-Tilt Sensor
If your boat does not have an analog gauge representing engine tilt, you can wire the adapter
directly to the sensor. All outboard and inboard/outboard motors that feature trim control should
have either a terminal or a wire allowing access to the engine-tilt sensor. Consult the owner’s
manual provided by your boat or sensor manufacturer to determine the type of sensor (resistive
or generic voltage) in use, and the sending and ground terminals on the sensor. Typically, the
sending terminal is labeled with an “S” marking for sensor or a “G” marking for gauge, and the
ground terminal is typically labeled with a negative sign (-). Wire the GET 10 adapter to the
sensor according to the following table.
•
◦
◦
◦
•
•
•
•
GET10InstallationandCongurationInstructions 
Connection Type Wire Color Gauge or Sensor Terminal
Analog Gauge Blue Sensor (S, G)
White Gauge power (+, +12V, I, IGN)
Yellow Unused
Black Ground (-, , G)
Red Unused
Resistive Sensor Blue Sensor (S, G)
White Unused
Yellow Unused
Black Ground (-, , G)
Red Unused
Generic Voltage (0–5 Vdc) Sensor Blue Unused
White Unused
Yellow Sensor (S, G)
Black Ground (-, , G)
Red Unused
After connecting the adapter to the gauge or sensor, cover any exposed wires with heat-notiCe:
shrink tubing.
Connecting the GET 10 Adapter to a NMEA 2000 Network
After you have connected the GET 10 adapter to the analog gauge or to the sender, connect it
to the existing NMEA 2000 network on your boat. If you do not have a NMEA 2000 network
on your boat, you must build one. For more information on NMEA 2000 and to purchase
additional connectors and cables, go to www.garmin.com.
To connect the GET 10 adapter to your existing NMEA 2000 network:
1. Determine where to connect the GET 10 adapter to your existing NMEA 2000 backbone.
2. Disconnect one side of a NMEA 2000 T-connector from the backbone. To extend the
NMEA 2000 backbone, connect a NMEA 2000 backbone extension cable to the side of the
disconnected T-connector.
3. Add the included T-connector for the GET 10 adapter to the NMEA 2000 backbone by
connecting it to the side of the disconnected T-connector.
4. Connect the NMEA 2000 connector on the GET 10 adapter to the T-connector added in
step 3.
5. (Optional) If the GET 10 adapter cannot connect directly to the NMEA 2000 backbone, route
a NMEA 2000 drop cable (not included) to the bottom of the T-connector added in step 3.
Use a drop cable with a length up to 20 ft. (6 m). Connect the drop cable to the T-connector
and to the NMEA 2000 connector on the adapter.
If you have an existing NMEA 2000 network on your boat, it should already be notiCe:
connected to power. Do not connect an additional NMEA 2000 power cable to an existing NMEA
2000 network, because only one power source should be connected to a NMEA 2000 network.

Product specificaties

Merk: Garmin
Categorie: Niet gecategoriseerd
Model: GET 10

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin GET 10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Garmin

Garmin

Garmin dēzl Headset 210 Handleiding

13 November 2024
Garmin

Garmin Edge Power Mount Handleiding

2 Oktober 2024
Garmin

Garmin Approach Z30 Handleiding

23 Juli 2024
Garmin

Garmin Tacx NEO 3M Handleiding

25 Juni 2024
Garmin

Garmin Delta SE Handleiding

9 Juli 2023
Garmin

Garmin Foretrex 801 Handleiding

8 Juli 2023
Garmin

Garmin BMW Motorrad Navigator VI Handleiding

19 Juni 2023
Garmin

Garmin GSD 26 Handleiding

18 Juni 2023
Garmin

Garmin Dash Cam 54 Handleiding

15 Juni 2023
Garmin

Garmin Varia ERTL615 Handleiding

6 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec

Vitec MGW Diamond-HX OG Handleiding

23 November 2024
Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Electrolux

Electrolux ZS70GL Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Stamos

Stamos S-PLASMA 60U Handleiding

23 November 2024