Garmin GBT 10 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin GBT 10 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 178 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
GBT 10 Installation and Conguration Instructions
Use the Garmin
®
GBT 10 Bennett Trim Tab Adapter to adapt analog information provided by
a Bennett Trim Tab Position Indicator (Bennett TPI), or by the Bennett trim tab sensors on
your boat, to your NMEA 2000
®
network. Your GBT 10 adapter allows you to observe trim tab
information on the compatible Garmin display devices connected to your NMEA 2000 network.
For a list of compatible Garmin chartplotters and devices, visit www.garmin.com.
Compare the contents of this package with the packing list on the box. If any pieces are
missing, contact your Garmin dealer immediately.
Product Registration
Help us better support you by completing our online registration today. Go to http://my.garmin
.com. Keep the original sales receipt, or a photocopy, in a safe place.
Contact Garmin
Contact Garmin Product Support if you have any questions while using your GBT 10 adapter.
In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913)
397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to www.garmin.com/support and click for in-country support Contact Support
information, or contact Garmin (Europe) Ltd. by phone at +44 (0) 870.8501241.
See the Important Safety and Product Information guide in the compatible Garmin display device box for
product warnings and other important information.
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or CAUTION:
sanding.
When drilling or cutting, always check the opposite side of the drilling or cutting NOTICE:
surface.
Needed Tools and Supplies
Heat-shrink tubing and a heat gun
Cable ties
Additional NMEA 2000 cabling and connectors (optional)
July 2009 190-01081-04 Rev. A Printed in Taiwan
 GBT10InstallationandCongurationInstructions
Determining an Installation Location
When you are selecting a location to install the GBT 10 adapter, consider the following:
During installation, you connect the GBT 10 adapter to the Bennett TPI (or directly to the
Bennett trim tab sensors), and to the NMEA 2000 network. Therefore:
Choose a location that is within 173 in. (4.4 m) of the Bennett TPI (or the Bennett trim
tab sensors) to avoid splicing bare wires.
Choose a location between the NMEA 2000 backbone and the Bennett TPI (or the
Bennett trim tab sensors).
If you cannot connect the adapter directly to the NMEA 2000 network, add a drop cable.
See for more information.page 3
The adapter is IEC 60529 IPX7 waterproof, and can be submerged up to 30 minutes at 1
meter. Do not install the adapter in a location where it will be submerged regularly, though
the location can be subject to wash-down.
You can use cable ties (not included) to secure the adapter to an existing structure on your
boat.
You can use mounted-head cable ties (not included) and screws (not included) to secure the
adapter to a bulkhead or other suitable surface on your boat.
Install the adapter at least 2 in. (5 cm) from a magnetic compass to prevent electromagnetic
interference, which can cause inaccurate compass readings.
Wiring the GBT 10 Adapter
Connect the GBT 10 adapter either to the Bennett TPI or to the Bennett trim tab sensors directly
using the bare wires on the wiring harness.
Wiring the GBT 10 Adapter to the Bennett
Trim Tab Display
You can wire the GBT 10 adapter directly to the Bennett
TPI. Do not remove any wires from the back of the
Bennett TPI, and wire the GBT 10 adapter to the TPI
according to the following table. Use only the wires listed
for the GBT 10 adapter. Cut and tape any unused wires.
*When wiring the GBT 10 adapter to the Bennett TPI, it is important that you do not connect
wires to the RED and GRN connections farthest from the SHLD connection. Connecting the
GBT 10 adapter wires to the connections farthest from the SHLD connection will interfere with
the operation of the Bennett TPI.
Bennett TPI
Connector
Label
GBT 10 Adapter
Wire Color
+ None
– None
BRG None
RED None*
RED Blue
SHLD Black
GRN Yellow
GRN None*
Bennett TPI
Connector
Label
GBT 10 Adapter
Wire Color
+ None
– None
BRG None
RED None*
RED Blue
SHLD Black
GRN Yellow
GRN None*
GBT10InstallationandCongurationInstructions 
Wiring the GBT 10 Adapter Directly to the Sensors on the Trim Tabs
You can wire the adapter directly to the Bennett trim tab sensors where the trim tabs are
installed. Wire the GBT 10 adapter to the sensors according to the following table.
GBT 10 Adapter Wire Bennett Trim Tab Sensors
Blue Port sensor wire 1**
White Port sensor wire 2**
Yellow Starboard sensor wire 1**
Drain Sensor drain wires
Red Starboard sensor wire 2**
**When wiring the GBT 10 adapter directly to the trim tab sensors, the connection order of the
GBT 10 adapter port wires (blue/white) and the GBT 10 adapter starboard wires (yellow/red) to
the two wires on the respective trim tab sensor is not important.
After connecting the adapter to the Bennett TPI or to the Bennett trim tab sensors, cover notiCe:
any exposed wires with heat-shrink tubing.
Connecting the GBT 10 Adapter to a NMEA 2000 Network
After you have connected the GBT 10 adapter to the Bennett TPI or to the Bennett trim tab
sensors, connect it to the existing NMEA 2000 network on your boat. If you do not have a
NMEA 2000 network on your boat, you must build one. For more information on NMEA 2000
and to purchase additional connectors and cables, go to www.garmin.com.
Connecting the GBT 10 Adapter to an
Existing NMEA 2000 Network
GBT10adapter
NMEA000device(notincluded)
Dropcable(optional-notincluded)
T-connector(oneincluded)
ExistingNMEA000network
To connect the GBT 10 adapter to your existing NMEA 2000 network:
1. Determine where to connect the GBT 10 adapter to your existing NMEA 2000 backbone.
2. Disconnect one side of a NMEA 2000 T-connector from the backbone. To extend the
NMEA 2000 backbone, connect a NMEA 2000 backbone extension cable to the side of the
disconnected T-connector.
3. Add the included T-connector for the GBT 10 adapter to the NMEA 2000 backbone by
connecting it to the side of the disconnected T-connector.
4. Connect the NMEA 2000 connector on the GBT 10 adapter to the T-connector added in
step 3.


Product specificaties

Merk: Garmin
Categorie: Niet gecategoriseerd
Model: GBT 10

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin GBT 10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Garmin

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd