FoneStar SONAIR-PRO-2P Handleiding

FoneStar Speaker SONAIR-PRO-2P

Lees hieronder de 📖 handleiding in het Nederlandse voor FoneStar SONAIR-PRO-2P (28 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
INSTRUCTION MANUAL/MANUAL DE USUARIO/
MODE D’EMPLOI/MANUAL DE INSTRUÇÕES
SONAIR-PRO-2P, SONAIR-PRO-2M,
SONAIR-PRO-2MP
DUAL UHF WIRELESS MICROPHONE SYSTEM
SISTEMA DOBLE DE MICROFONÍA INALÁMBRICA UHF
SYSTÈME DE MICROPHONE SANS FIL UHF DOUBLE
SISTEMA DE MICROFONES DUPLO SEM FIOS UHF
EN
- 2 -
DESCRIPTION
- Wireless microphone with superior sound, stable operation and excellent interference behaviour.
- The microphone integrates the ID Pilot function which pairs the receiver and transmitter with a unique
16-bit code, preventing other microphones from interfering even on the same frequency. In addition, the
diversity reception with two antennas ensures the best RF reception.
- The display on the microphone and on the receiver easily informs about frequency and battery status.
Facilitating the control of microphones.
- The transmitter uses an integrated audio and transmission management solution on a single chip, with
frequency selection and efficient power management to maximise battery life. FM modulation technology
with high sound quality.
- The receiver and microphone channels are quickly synchronised with the IR synchronisation function.
- UHF frequency range with selectable transmission channels.
- Receiver with colour display and low noise balanced and unbalanced output for easy connection.
- : dual receiver + 2 belt-pack with clip-on microphone.SONAIR-PRO-2P
SONAIR-PRO-2M: dual receiver + 2 hand-held microphone.
SONAIR-PRO-2MP: dual receiver + 1 hand-held + 1 belt-pack with clip-on microphone.
CONTROLS AND FUNCTIONS
SONAIR-PRO-2P, SONAIR-PRO-2M & SONAIR-PRO-2MP RECEIVER
402
CH 398
CH
680.10
MHz
679.70
MHz
A A B B
VOL 97% VOL 76%
1 12 23 4 346 75
1.- : multifunction controls. VOL | CH
- rotation: independent volume controls for channels A and B on the audio outputs.
- long press + rotate: enters the configuration mode and selects the channel (transmission
frequency), the channel number will be shaded when this mode is active 402
CH CH 402 . To exit
the configuration mode, long press again or wait a few seconds and it will automatically deactivate.
2.- SYNC: a long press activates the synchronisation of the transmission channel (frequency) and a short
press stops it. For more information, see section OPERATING INSTRUCTIONS - RECEIVER AND
TRANSMITTER SYNCHRONISATION.
3.- : audio signal indicator lights for channel A and channel B audio signals. It will light up orange when AF
receiving audio signal from the microphone. Do not allow the last red LED to illuminate as this will mean
that the signal is saturating; if this happens, decrease the volume of the channel.
4.- RF: radio frenquency signal indicator lights for channel A and channel B. It will light up green when
receiving radio frequency signal from the microphone.
5.- : IR sensor for synchronisation of the transmission channel (frequency).IR
6.- Information display.
7.- : receiver on/off button and indicator light. Make a short press to switch on and a long press to switch
off the receiver.
EN
- 3 -
1 12 3 4
1.- : antennas for signal reception of A and B channel microphones with diversity technology.ANT A/B
2.- MIX OUT: audio signal output of the mix of both channels A and B, 6.3 mm unbalanced jack connector.
3.- AUDIO OUT CH A/CH B: audio signal outputs for each independent channel A and B, balanced XLR
connectors.
4.- : power input 12 V DC, 1 A.POWER IN
SONAIR-PRO-2M & SONAIR-PRO-2MP TRANSMITTER
HI
CHANNEL
MHz
1 2 43
1.- Information display showing the transmission frequency.
2.- : IR sensor for synchronisation of the transmission channel (frequency).IR
3.- : microphone on/mute/off button. Short press to turn on and long press to turn off the microphone.
If it is on, short press to mute the audio and press again to restore it.
4.- Battery holder for 2 AA batteries. The use of rechargeable batteries is also possible.
SONAIR-PRO-2P & SONAIR-PRO-2MP TRANSMITTER
CH
BMHz
POWER ON OFF -VOL+
1
2
35
4
10
6 7 8 9
CH
BMHz
IR
PIN 3 PIN 1
PIN 2
1.- RF antenna.
2.- Information display showing the transmission frequency.
3.- Battery holder for 2 AA batteries. The use of rechargeable batteries is also possible.
4.- : IR sensor for synchronisation of the transmission channel (frequency).IR
5.- Attachment clip.
6.- : microphone turn on LED power indicator.POWER
7.- : 3-position microphone power selector: microphone ON, audio mute and microphone OFF. ON/OFF
8.- : microphone audio volume control.-VOL+
9.- Microphone plug, miniXLR connector.
10.- Clip-on belt-pack microphone. miniXLR connector (PIN 1: ground, PIN 2: not connected, PIN 3: signal).


Product specificaties

Merk: FoneStar
Categorie: Speaker
Model: SONAIR-PRO-2P

Heb je hulp nodig?

Als je hulp nodig hebt met FoneStar SONAIR-PRO-2P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker FoneStar

Handleiding Speaker

Nieuwste handleidingen voor Speaker