Fluke T5-600 Handleiding

Fluke Thermometer T5-600

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke T5-600 (6 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

PN 686953

March 1998 Rev.1, 9/01

T5-600/T5-1000

Electrical Tester

Service Information

Introduction

This service information sheet provides the following information for the T5-600 and T5-1000 Electrical

Testers (hereafter referred to as "the tester").

• Safety information

• Parts and service information

• Specifications

• Cleaning procedure

• Required equipment

• Performance tests

• Parts and accessories list

• Battery replacement procedure

For operating instructions, refer to the T5-600/T5-1000 Electrical Tester Instruction Sheet.

Safety Information

Warning

To avoid possible electric shock or personal injury, follow these guidelines:

• Do not use the tester if it is damaged or operating abnormally. Protection

may be impaired.

• Before each use:

• Make sure the battery door is closed and latched.

• Inspect the tester and test leads. Look for cracks, missing plastic, exposed

metal, or damaged insulation. Replace damaged test leads before using the

tester.

• Verify the tester’s operation by measuring a known voltage.

• Replace the batteries as soon as the low battery indicator (M) appears.

• Do not use the tester around explosive gas, vapor or dust.

• Do not apply more than the rated voltage, as marked on the tester, between

terminals or between any terminal and earth ground.

• Refer servicing to qualified personnel.

• Use caution when working above 30 V ac rms, 42 V ac peak, or 60 V dc.

• When using the probes, keep your fingers behind the finger guards on the

probes.

• Connect the common test lead before you connect the live test lead.

Disconnect the live test lead first.

• The display will not display hazardous voltages in display hold. The voltage

indicator LED ( ) continues to operate.

Service Information

Serial Numbers 79559999 and Below

General Specifications (continued)

RF Field Specification 0.5 % full scale + (specified accuracy) at 3 V/m

Safety Complies with ANSI/ISA-S82.01-94, UL Classified to IEC 61010, CSA/CAN C22.2 No.1010.1-

92, and EN61010-1 1995.

EMC EN 61326

Certifications In accordance with IEC 61010-1 54CJ

Resolution and Accuracy

Function T5-600 Range T5-1000 Range Resolution Accuracy

K600 V rms 1000 V rms 1 V ±(1.5 % + 2 digits)

L600 V 1000 V 1 V ±(1 % + 1 digit)

?100.0 A 100.0 A 0.1 A ±(3 % + 3 digits)

e1000 1000 1 Ω Ω Ω ±(1 % + 2 digits)

Input Characteristics

Input Protection

Function T5-600 T5-1000

Input impedance (nomial

K600 V rms 1000 V rms 1 MΩ, <100 pF ac-coupled

L600 V rms 1000 V rms 1 MΩ, <100 pF

e600 V rms 1000 V rms

Open Circuit Test Voltage Short Circuit Current

e1.65 V dc (nominal) <600 µA

CAT III protects against transients in a fixed equipment installation such as a distribution panel, and lighting systems in

large buildings.

CAT IV protects against transients from a primary supply such as an electricity meter or an overhead or underground utility

service.

Serial Numbers 79559999 and Below

General Specifications

Calibration One-year calibration cycle.

Maximum Voltage

Between any Terminal

and Earth Ground

T5-600: 600 V rms, Overvoltage Category III

T5-1000: 1000 V rms, Overvoltage Category III

Temperature Operating: -10 ° ° ° ° ° ° ° °C to +50 C (14 F to 122 F); Storage: -30 C to +60 C (-22 F to +140 F)

Altitude Operating: 2000 m (6562 ft); Storage: 10,000 m (32808 ft)

Relative Humidity 0 % to 95 %, 5 ° °C to 30 C (41 C (86 °F to 86°F); 0 % to 75 %, 30 ° °C to 40 °F to 104 °F);

0 % to 45 %, 40 ° °C to 50 C (104 °F to 122 °F)

Battery Type and Life AA (2); 400 hours continuous with alkaline; 200 hours continuous with zinc chloride

Service Information

Equipment Required for Performance Tests

The following equipment is required for performance tests:

• Fluke 5500A Multi-Product Calibrator, or equivalent

• 0 V to 5 V adjustable dc power supply

• Approximately 8 m (26 ft) of #14 single-conductor magnet wire wound into a butterfly-shaped coil.

Figure 1 shows how to make the coil.

Performance Tests

Use the following procedures to verify the tester’s performance. If the tester fails any of the tests, return it to

Fluke for calibration or repair.

Testing the AC Current Function

The tests in this section require the butterfly coil shown in Figure 1. Note that the 10 conductors in the middle

of the coil cause the tester to read 10 times more current than the calibrator supplies.

1. Put one edge of the butterfly coil in a vice to hold the coil during testing.

2. Set the calibrator to the current and frequency given in Step 1 of Table 1.

3. Connect the butterfly coil to the calibrator.

4. Set the tester to the amperage function.

5. Place the tester’s current fork around the middle of the coil so that the alignment marks are centered and

perpendicular to the wire bundle, as shown in Figure 1.

6. Verify that the tester reads within the display limits shown for Step 1 in Table 1.

7. Apply the currents and verify the tester’s readings for the remaining steps in Table 1.

Table 1. AC Current Tests

Step Calibrator output T5-600/T5-1000 Display Limits

1 10 A, 60 Hz 96.7 to 103.3

2 10 A, 45 Hz 96.7 to 103.3

3 0.5 A, 45 Hz 4.5 to 5.5

Product specificaties

Merk:	Fluke
Categorie:	Thermometer
Model:	T5-600
Gewicht:	300 g
Beeldscherm:	LCD
Accu/Batterij voltage:	1.5 V
Waterdicht:	Ja
Stofwerend:	Ja
DC voltage bereik:	0 - 600 V
Afmetingen (B x D x H):	30.5 x 51 x 203 mm
Type product:	Digitale multimeter
AC voltage bereik:	0 - 600 V
AC stroom bereik:	0 - 100 A
Weerstand bereik:	0 - 1000 Ohm