Fluke i30 Handleiding

Fluke Meetapparatuur i30

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke i30 (10 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
PN 2560394
March 2006
©2006 Fluke Corporation. All rights reserved.
®
i30s/i30
AC/DC Current Clamps
Instruction Sheet
Introduction
The i30s AC/DC Current Clamp has been designed for use with
oscilloscopes and DMMs for accurate, non-intrusive
measurement of both AC, DC, and complex waveform currents.
The i30 AC/DC Current Clamp has been designed for use with
DMMs only. Using advanced Hall Effect technology the i30s can
accurately measure currents with a resolution of 1 mA from 5 mA
to 30 A over the frequency range of DC to 100 kHz. These
features make it a powerful tool for use in inverters, switch mode
power supplies, industrial controllers and other applications
requiring current measurements and/or waveform analysis.
Symbols
The table below lists the symbols used on the product and/or in
this manual.
Symbol Description
~ Do not dispose of this product as unsorted municipal
waste. Contact Fluke or a qualified recycler for
disposal.
W Important Information. See manual.
T Double insulation.
- Do not apply around or remove from the HAZARDOUS
LIVE conductors.
) Conforms to Canadian Standards Association.
P Complies with the relevant European standards.
Safety Instructions
Please read this section carefully. It will make you familiar with
the most important safety instructions for handling your product.
In this instruction sheet, a Warning identifies conditions and
actions that pose hazard(s) to the user. A Caution identifies
conditions and actions that may damage the calibrator or the test
instruments.
W
W
W
WW X
X
X
XX Warning
The i30s and i30 may only be used and handled by
qualified personnel. To avoid personal injury, follow
these precautions:
• To avoid electric shock, use caution during
installation and use of this product; high
voltages and currents may be present in circuit
under test.
• Do not use the product if damaged. Always
connect probe to display device before it is
installed around the conductor.
• Always ensure the probe is removed from any
live electric circuit, and leads are disconnected
before removing the battery cover.
• Use the Current Probe only as specified in the
operating instructions; otherwise the current
probe’s safety features may not protect you.
• Adhere to local and national safety codes.
Individual protective equipment must be used
to prevent the shock and arc blast injury where
hazardous live conductors are exposed.
• Do not hold the Current Probe anywhere
beyond the tactile indicator.
• Before each use, inspect the Current Probe.
Look for cracks or missing portions of the
Current Probe housing or output cable
insulation. Also look for loose or weakened
components. Pay particular attention to the
insulation surrounding the jaws.
• Use caution when working with voltages above
60 V dc, 30 V ac rms or 42 V ac peak. Such
voltages pose a shock hazard.
• Use of this equipment is designed to protect
against transients in equipment in fixed
equipment installations, such as distribution
panels., feeders and short branch circuits, and
lighting systems in large buildings.
• Use of this equipment in a manner not specified
herein may impair the protection provided by
the equipment.
• CAT III equipment is designed to protect against
the transients in the equipment in fixed
equipment installations, such as distribution
panels, feeders and short branch circuits, and
the lighting systems in large buildings.
Specifications
Electrical Characteristics
All accuracies stated at 23°C ± 1°C
Current range 20 A ACRMS or DC
Measuring range ± 30 A
Overload capacity 500 A
Output sensitivity 100 mV/A
Accuracy (at 25 °C) ± 1 % of reading ± 2 mA
Resolution ± 1 mA
Typical output noise
level
200 µVRMS
Load impedance > 100 k Ohms ≤ 100 pF
Conductor position
sensitivity
± 1 % relative to center reading
Frequency range
i30s DC to 100 kHz (0.5 dB)
i30 DC to 20 kHz (0.5 dB)
di / dt following 20 A / µs
Response time Better than 1 µs
Temperature
coefficient
± 0.01 % of reading / °C
Operating humidity: 15 to 85 % (non
condensing)C
Altitude: 2000 m
Power supply 9 V Alkaline, NEDA 1604/PP3
IEC 6LR61
Working voltage
(see Safety
Standards)
300 V ACRMS or DC
Battery life 30 hours, low battery indicator

Product specificaties

Merk: Fluke
Categorie: Meetapparatuur
Model: i30

Heb je hulp nodig?

Als je hulp nodig hebt met Fluke i30 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Meetapparatuur Fluke

Fluke

Fluke FEV350 Handleiding

10 Juni 2024
Fluke

Fluke 319 Handleiding

26 Juli 2023
Fluke

Fluke T150/VDE Handleiding

18 Juli 2023
Fluke

Fluke i400 Handleiding

15 Juni 2023
Fluke

Fluke 301D Handleiding

15 Juni 2023
Fluke

Fluke 1507 Handleiding

15 Mei 2023
Fluke

Fluke T110VDE Handleiding

4 Mei 2023
Fluke

Fluke i400s Handleiding

3 Mei 2023
Fluke

Fluke 1503 Handleiding

1 Mei 2023
Fluke

Fluke 393 Handleiding

17 April 2023

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

Testec

Testec TT-CC 550 Handleiding

14 November 2024
Eastron

Eastron SDM630 Handleiding

14 November 2024
GW Instek

GW Instek PEL-3032E Handleiding

14 November 2024
Klein Tools

Klein Tools ET19 Handleiding

12 November 2024
Voltcraft

Voltcraft VC-55 LCD SE Handleiding

11 November 2024
Hikmicro

Hikmicro Eco-V Handleiding

11 November 2024
Testboy

Testboy TB115 Bit Handleiding

11 November 2024
Uni-T

Uni-T UT673PV Handleiding

5 November 2024
Sauter

Sauter 281-301 Handleiding

3 November 2024
Sauter

Sauter TVL-XL Handleiding

3 November 2024