Fluke BP190 Handleiding

Fluke Accu BP190

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke BP190 (2 pagina's) in de categorie Accu. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

BP190

NiMH Rechargeable Battery Pack

Instruction Sheet

Introduction

The BP190 is a NiMH (Nickel-Metal Hydride)

Rechargeable Battery Pack designed for use with the

Fluke ScopeMeter 190 series.

Specifications

Nominal voltage: 7.2 V

Capacity: 3500 mAh

Allowable ambient temperature during storage:

-20 °C to +60 °C (-4 °F to +140 °F)

Allowable ambient temperature during operating :

0 °C to +50 °C (+32 °F to +122 °F)

Allowable ambient temperature during charging:

0 °C to +40 °C (+32 °F to +104 °F)

June 1999, Rev.1, 10/01

Printed in the Netherlands

All product names are trademarks of their respective companies.

Using the Battery Safely

In this instruction sheet a Warning identifies conditions

and actions that pose hazard(s) to the user. Symbols

used on the BP190 and in this instruction sheet are

explained in the next table.

Recycling information

Disposal information

Warning

Do the following to avoid electrical shock

or fire:

• Do not short circuit the battery.

• Do not expose the battery to fire

Disposing the Battery Pack

Do not dispose of the NiMH (Nickel-Metal

Hydride) battery pack with other solid waste.

Used batteries should be disposed of by a

qualified recycler or hazardous materials

handler. Contact your authorized FLUKE

Service Center for recycling information.

General Battery Care

The life of NiMH batteries is strongly influenced by the

care that they receive. If properly maintained, the

battery is capable of more than 500 charge/discharge

cycles before dropping to 80% of capacity. Do not

exceed the allowable ambient temperatures during

charging, operating, or storage.

Caution

To prevent decrease of the battery

capacity, you must charge the batteries at

least once a year.

Limited Warranty & Limitation Of Liability

This Fluke product will be free from defects in material

and workmanship for one year from the date of

purchase. This warranty does not cover damage from

accident, neglect, misuse or abnormal conditions of

operation or handling. Resellers are not authorized to

extend any other warranty on Fluke’s behalf. To obtain

service during the warranty period, send your defective

product to the nearest Fluke Authorized Service Center

with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO

OTHER WARRANTIES, SUCH AS FITNESS FOR A

PARTICULAR PURPOSE, ARE EXPRESSED OR

IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES OR LOSSES, ARISING FROM ANY

CAUSE OR THEORY.

Since some states or countries do not allow the

exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of

liability may not apply to you.

Fluke Corporation Fluke Industrial B.V.

P.O. Box 9090 P.O. Box 90

Everett WA 7600 AB Almelo

98206-9090, USA The Netherlands

Service Centres

For service information, contact your Fluke service

center. To locate an authorized service center, visit us

on the World Wide Web:

http://www.fluke.com

or call Fluke using any of the phone numbers listed

below:

+1-888-993-5853 in U.S.A. and Canada

+31-402-675-200 in Europe

+1-425-446-5500 from other countries

Replacing the Battery Pack

Warning

To avoid electrical shock, remove the test

leads and probes before replacing the

battery pack.

Usually it should not be necessary to replace the

battery pack. However, if you replace the battery pack,

follow steps 1 to 9. (See the figures.) Use a #10 Torx

screwdriver for all screws.

Disconnect the test leads and probes both at the source

and at the test tool before you open the test tool.

1. Loosen the two screws of the top cover.

2. Place the test tool face down and loosen the two

screws of the bottom cover.

3. Remove the top cover and bottom cover.

4. Loosen the two screws of the back cover.

5. Lift the back cover away from the test tool.

6. Take the battery out of the battery compartment.

7. Remove the battery plug from the connector.

8. Install a new battery pack.

Note

Ensure that the battery pack is placed in the

battery compartment as shown in step

. Use

only the Fluke BP190 NiMH Battery Pack.

9. Reinstall all covers in reversed order.

Note

When new, the NiMh battery may be empty

and must be charged for 4 hours (test tool is

off) to fill it completely.

Product specificaties

Merk:	Fluke
Categorie:	Accu
Model:	BP190
Capaciteit van de accu/batterij:	3500 mAh
Accu/Batterij voltage:	7.2 V
Aantal per verpakking:	1 stuk(s)
Oplaadbaar:	Ja
Compatibiliteit:	ScopeMeter 190/190C Series\nFluke 430 Series
Bandbreedte:	- MHz
Batterijtechnologie:	Nikkel-Metaalhydride (NiMH)