Flashforge Creator 3 Handleiding
Flashforge
3D Printer
Creator 3
Lees hieronder de 📖 handleiding in het Nederlandse voor Flashforge Creator 3 (100 pagina's) in de categorie 3D Printer. Deze handleiding was nuttig voor 126 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/100
This guide is only applicable to FLASHFORGE Creator 3 3D printer
本手册仅适用于闪铸科技 打印 金刚狼3 3D 机
中文P51
用户使用手册
USER GUIDE
CN/EN-A01 Creator 3 金刚狼3
01
PREFACE
Note:
Dear Flashforge users, thank you for choosing Flashforge products. Thank you for your great support and help for
Flashforge. Please read this guide carefully before use and follow the instructions strictly. The whole Flashforge team
will provide you with superior service. No matter what problems you encounter during use, please contact us according
to the phone number and email address provided at the end of the guide.
In order for you to better experience our products, you can also acquire skills about the equipment operation from the
following sources.
(1) User Guide:
Please unpack the box carefully. Then you can take out the attached documents from the top foam or browse the latest
user guide from the USB disk. This will help you familiarize yourself with the equipment and successfully complete your
first printing.
(2) Official Flashforge Website:
Flashforge Chinese website: www.sz3dp.com
Flashforge English website: www.flashforge.com
You can visit the Flashforge official website to obtain information about related software and hardware, contact
information, equipment operation, equipment maintenance and other related information.
Every 3D printer has undergone printing test before leaving factory. If there are some residues in the extruder
of the equipment or some slight scratches on the build plate, it is normal and will not affect its use.
NOTICE
Keep Creator 3's work table clean and tidy.
Do not operate Creator 3 in the presence of flammable liquids, gases or dust. (The high temperature generated by
equipment operation may react with airborne dust, liquids, and combustible gases and cause fire.)
Keep Creator 3 out of children and untrained persons' reach.
PLEASE STRICTLY FOLLOW ALL THE SAFETY WARNINGS AND NOTICES BELOW ALL THE TIME.
WORK ENVIRONMENT SAFETY
Make sure to use Creator 3 with a properly grounded outlet. Do not refit Creator 3's plug. (Ungrounded/improperly
grounded/modified plug will inevitably increase the risk of electric leakage.)
Do not expose Creator 3 to damp or hot-sun environment. (Humidity will increase the risk of electric leakage./Expo-
sure to sunlight will accelerate the aging of plastic parts.)
Make sure to only use the power supply provided by Flashforge.
Do not use Creator 3 during an thunderstorm.
Please shut down Creator 3 and unplug it if it is not in use for a long time.
ELECTRICAL SAFETY
Do not touch the extruder and build plate, etc during printing.
Do not touch the extruder when finishing printing.
Dress properly. Do not wear scarves, masks, gloves, jewelry ornaments or other objects that can easily get caught in
the equipment when operating it.
Do not operate Creator 3 while you are tired or under the influence of drugs, alcohol or medication.
PERSONAL SAFETY
02
Do not leave the running equipment for a long time.
Do not make any modifications to the equipment.
Please keep the distance between the extruder and the build plate for at least 50mm during filament loading
operation. (Too-close distance may cause extruder blockage.)
Operate the equipment in a well-ventilated environment.
Do not use the equipment for illegal activities.
Do not use the equipment to make any food storage products.
Do not use the equipment to make any electrical appliances.
Do not put the printed model into your mouth.
Do not remove the printed models with brute force.
Do not connect the equipment with the network cable longer than 3m.
CAUTIONS
Temperature: RT 15-30℃
Humidity: 20%-70%
ENVIRONMENT REQUIREMENTS
The equipment must be placed in a dry and ventilated environment. The distances of the left, right and rear side
space of the equipment should be at least 20cm, and the distance of the front side space should be at least 35cm.
EQUIPMENT PLACING REQUIREMENTS
Do not unpack the filament until it is needed for use. Please store the filament in a dry and dust-free environment
after unpacking.
FILAMENT STORAGE REQUIREMENTS
When using the equipment, please use Flashforge filaments or other filaments provided or specified by Flashforge.
There is a wide variety of filaments on the market with varying quality. Poor quality or incompatible filaments can
easily cause extruder blockage and extruder damage.
COMPATIBLE FILAMENT REQUIREMENTS
Do not copy or print any items prohibited by law.
According to local laws, it is generally illegal to copy or print the following items：
1. Gun
2. Copy works protected by the copyright. Some copyrighted works may be allowed to be partially copied for "fair
use". Multiple copies will be regarded as improper use. Artistic works are equivalent to copyrighted works.
The above list is for reference only and does not include all contents. Flashforge shall not be liable for its complete-
ness or accuracy. If you have questions regarding the legality of copying or printing certain items, please consult the
legal counsel.
LEGAL NOTICE
Product specificaties
| Merk: | Flashforge |
| Categorie: | 3D Printer |
| Model: | Creator 3 |
Heb je hulp nodig?
Als je hulp nodig hebt met Flashforge Creator 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding 3D Printer Flashforge
8 April 2024
25 Juli 2023
25 Juli 2023
7 Mei 2023
2 Mei 2023
20 April 2023
3 April 2023
24 Maart 2023
23 Maart 2023
23 Maart 2023
Handleiding 3D Printer
- 3D Printer Anker
- 3D Printer BQ
- 3D Printer Dimension
- 3D Printer Gembird
- 3D Printer German RepRap
- 3D Printer GooVer
- 3D Printer Kodak
- 3D Printer MakerBot
- 3D Printer Polaroid
- 3D Printer PP3DP
- 3D Printer Renkforce
- 3D Printer Velleman
- 3D Printer Weistek
- 3D Printer Weller
- 3D Printer 3D Systems
- 3D Printer Exibel
- 3D Printer Monoprice
- 3D Printer Wanhao
- 3D Printer XYZprinting
- 3D Printer Leap Frog
- 3D Printer Snapmaker
- 3D Printer Easy Threed
- 3D Printer Anycubic
- 3D Printer Creality3D
- 3D Printer Artillery
- 3D Printer Zortrax
- 3D Printer LulzBot
- 3D Printer SINDOH
- 3D Printer Wasp
- 3D Printer Creality
- 3D Printer Raise3D
- 3D Printer Craftbot
Nieuwste handleidingen voor 3D Printer
19 November 2024
19 November 2024
19 November 2024
19 November 2024
15 November 2024
29 Juli 2024
29 Juli 2024
29 Juli 2024
29 Juli 2024
18 Juni 2024