Fibaro FGSS-001 Handleiding

Fibaro Rookmelders FGSS-001

Lees hieronder de 📖 handleiding in het Nederlandse voor Fibaro FGSS-001 (2 pagina's) in de categorie Rookmelders. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

ENG

OPERATING MANUAL

SMOKE SENSOR

FGSS-001 v2.1 - v2.3

The Fibaro Smoke Sensor is a universal, optical Z-Wave smoke sensor. The

device can be hard wired (12 or 24 VDC) or battery operated (battery life 3 years*).

Smoke detection is signaled through siren and LED diode blinking. Additionally, the

smoke sensor signal can be sent to an alarm system or fire alarm system hub,

through a NC (normally closed) contact terminals.

The optical sensor detects smoke at an early stage of fire, often before flames

appear and temperature starts to rise significantly. Moreover the device has a

built-in temperature sensor, which can also trigger the alarm once the specified

temperatute threshold is exceeded.

The Fibaro Smoke Sensor is designed to be placed on a wall or ceiling. LED

indicator signals fire, operating mode and used to see if device is within the

Z-Wave network. The smoke sensor is designed to operate in confined spaces,

under normal conditions (lacking smoke, dust, condensed water vapor).

SPECIFICATIONS

Power Supply:

Battery Type:

Power Consumption

(at VDC operation):

Output terminals maximum current

carrying capacity

(SMOKE NC, TAMP NC):

Maximum voltage at output terminals

(SMOKE NC, TAMP NC):

EU standards compliance:

Radio protocol:

Radio frequency:

Range:

Operational Temperature:

Measured Temperature Range:

Temperature Measuring Accuracy:

Dimensions (Diameter x Height):

12 - 24 VDC

CR123A

0,4W

25mA

24V (AC or DC)

EMC 2004/108/EC

R&TTE 199/5/WE

Z - Wave

868,4 MHz EU;

908,4 MHz US;

921,4 MHz ANZ;

869,2 MHz RU;

up to 50m outdoors

up to 30m indoors

(depending on terrain and building

structure)

0 - 40oC

-20 to 100oC

0,5oC (within 0oC - 40oC range)

65 x 28 mm

TECHNICAL INFORMATION

• Compatible with any Z-Wave Controller.

• May be connected to any alarm or fire prevention system by hard wiring NC

output

• Extremely easy installation - simply install it in location prone to fire.

• Battery or VDC powered.

• Built-in tamper switch.

• Alarm is signaled by sound and LED diode.

• Fire detection through air temperature measuring.

• Can trigger alarm just by exceeding temperature threshold.

• 3 levels of sensors sensitivity.

• Automatic efficiency test performed every 5 seconds.

• Built-in “black box” allows the device to report and record smoke and temperature

readouts.

I. Z-WAVE NETWORK INCLUSION

There are two ways to include a Fibaro Smoke Sensor into the Z-Wave network:

1) Automatically, using the auto inclusion function (available in constant current

powering mode), or

2) Manually - using the B-button (option available in both powering modes -

hard wired or battery powered).

Including a Fibaro Smoke Sensor into the Z-Wave network in auto inclusion mode:

1) Make sure the Fibaro Smoke Sensor’s power is disconnected and/or the battery

is removed prior to auto inclusion and located within the direct range of Z-Wave

controller.

2) Set the main controller into the learning mode

(see main controller’s operating manual).

3) Connect the power to the sensor to include it into the Z-Wave network.

4) Fibaro Smoke Sensor will be detected and included into the Z-Wave network.

III. SENSOR INSTALLATION

Fig. 1 - Fibaro Smoke Sensor top view.

BATTERY TIPS

Fibaro Smoke Sensor’s battery life is approximately 3 years when

on optimum settings. The current battery level is displayed in the

Home Center 2 interface. Red battery icon means that battery

needs replacement. In order to avoid triggering tamper alarm while

replacing the battery, 2-nd association group’s associations must

be deleted, and Sensor’s parameters’ configuration set to default.

In addition, the device itself, apart from the main controller,

monitors the battery level and a low battery is signaled with a

yellow blinking LED and an intermittent sound alarm (interval set

in parameter 87). The Fibaro Smoke Sensor can signal a low

battery level for approximately 30 days.

IV. POWERING MODES

There are two powering modes for the Fibaro Smoke Sensor. By default it’s

current, after connecting a 12 / 24 VDC power source to +12/24 and GND

terminals (see diagram #3). Powering mode configuration is carried out

automatically, while sensor is being included into the Z-Wave network. When

battery powered, a Fibaro Smoke Sensor communicates with the Z-Wave network

main controller periodically. Smoke detection is sent immediately. Configuration

parameters and association settings are sent periodically at specified wake up

intervals, or at a manual wake up (triple click B-button). In DC powering mode,

configuration and association parameters are sent when necessary, and

additionally the smoke sensor serves as a Z-Wave signal repeater.

Switching to a constant current powering mode:

1) Exclude a sensor from the Z-Wave network.

2) Disconnect the battery,

3) Install the constant power connecting terminal, observing the diagram #3.

4) Connect the constant current power to the power terminal (12 / 24 VDC) to +12

and GND terminals observing wiring diagram #3.

5) Include Fibaro Smoke Sensor into the Z-Wave network.

NOTE

1. It’s not possible to power the device from a battery and VDC

power source simultaneously. When using a VDC power souce it’s

recommended to use another kind of power back up.

2. Home Center 2 checks the battery level once a day.

NOTE

Read this manual before attempting to install the device. Failure to

observe recommendations included in this manual may be

dangerous or cause a violation of the law. The manufacturer, Fibar

Group Sp. z o.o., will not be held responsible for any loss or

damage resulting from not following the instructions of operating

manual.

NOTE

Work within local code height requirements for installation of the

Fibaro Smoke Sensor. Take special precautions during installation

and use tools and equipment in perfect working order. It’s

recommended to observe ladders, lifts and other obstacles.

NOTE

Maintenance inspections should be perfomed regularly, by a

trained staff member. Fibar Group Sp. z o.o. recommends the

functional and visual checks to be performed at least once a

month. Functional check, includes self test (described below) and

triggering smoke detection.

NOTE

When handled carelessly or used in non-specified environment

conditions, the device may not function properly. It’s highly

recommended to take all safety precautions to ensure safety and

property protection.

NOTE

Depending on the Smoke Sensors internal conditions (e.g. battery

discharge, device failure, etc.) and installation conditions, this

device may not be 100% accurate. This device can significanlty

increase the probability of fire detection. Smoke Sensors must be

tested regularly according to this operating manual and local code.

Ventilation systems, chimneys and potentially dangerous devices

that can cause a fire should be regularly inspected as well.

NOTE

In case the device is not detected, include it manually (as

described below) or reset the sensor and repeat the procedure

above.

In order to turn off the auto inclusion function, press the B-button once after the

power source has been connected to the Fibaro Smoke Sensor.

Manual Fibaro Smoke Sensor inclusion:

1) Connect the power source to the Fibaro Smoke Detctor and/or install the battery.

Make sure the device is located within direct range of the Z-Wave controller.

2) Set the main controller into the learn mode (see main controller’s operating

manual).

3) Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure.

4) Fibaro Smoke Sensor will be detected and included in the Z-Wave network.

II. EXCLUDING FIBARO SMOKE SENSOR FROM THE Z-WAVE NETWORK

1) Make sure the sensor is connected to power source (battery and/or hard wired).

2) Set the main controller into the learn mode (see main controller’s operating

manual)

3) Quickly, triple click the B-button, located on Fibaro Smoke Sensor’s enclosure.

5) Screw the Fibaro Smoke Sensor into the cover.

6) If the sensor is already included in the Z-Wave network, wake it up by triple

clicking the B-button..

7) Test Fibaro Smoke Sensor’s operation by using a dedicated optical smoke

sensor diagnostic tool.

8) Test the Z-Wave network assuring the device is within range.

NOTE

It’s recommended to install the sensor on the ceiling or upper

portion of wall at least 40 cm (2 feet) from corners and other

objects. Particular attention should be paid to any adjacent objects

or devices which can impede smoke’s access to the sensor. It’s

recommended to install Fibaro Smoke Sensor in all rooms prone

to fire, and in between such rooms as well.

INSTALLATION NOTES:

1) When choosing location of smoke sensor, make sure the alarm sound can be

easily audible in other rooms in the building.

2) It’s recommended to install the sensor in already decorated, painted rooms.

3) It’s recommended to install the sensor at least 1,5m from air conditioners.

4) Do not install the sensor in insolated places. Keep at least 0,5m distance from

light sources.

5) Do not install the sensor in places prone to draughts.

6) Do not install the sensor in places with high water vapor condensation, e.g.

above stoves, ovens, kettles, etc.

Diagram 1 - DC Power adapter connection.

Diagram 2 - Alarm system hub connection.

DIAGRAMS DESCRIPTION:

+12V - constant power supply terminal, 12/24VDC

-GND - ground terminal

SMOKE NC - potential free, smoke sensor connecting terminals

(for wired systems)

TAMP NC - potential free, tamper connecting terminals (for wired systems).

V. SMOKE DETECTION

Fibaro Smoke Sensor responds to the physical presence of smoke. Smoke

presence is required for the device to react. Fibaro Smoke Sensor performs a self

test every 5 seconds (see section VII) and checks for smoke presence. When

smoke is detected, the sensor checks 3 more times, at 1 second interval to see,

whether the smoke is actually present. Once the smoke presence is confirmed,

Fibaro Smoke Sensor triggers an alarm.

Smoke alarm is signaled by sending an appropriate alarm frame to devices and the

Z-Wave controller, opening NC contact, and also by a constant sound signal and

LED diode blinking red. Once the smoke alarm has ceased, the sensor checks 3

times, at 1 second interval, whether the smoke has actually disappeared before

getting back to normal operation, i.e. performing a self test each 5 seconds and

checking for presence of smoke.

NOTE

As described in section V, the Fibaro Smoke Sensor checks for

smoke presence every 5 seconds. In addition, the device checks

for damage and tests the Z-Wave network communication at each

wake up interval (see section VIII).

NOTE

Fibaro Smoke Sensor is a multiple use device, however, for

greater safety, it’s recommended to replace the device with a new

one after a fire occurance.

VI. DETECTING FIRE THROUGH TEMPERATURE ALARM

Apart from detecting smoke presence, Fibaro Smoke Sensor can detect fire by

recording a rapid temperature rise. Temperature alarm threshold is user defined

(parameter 81). Temperature alarm is signaled by the blinking red LED signaling

diode blinking red and an intermittent sound signal.

NOTE

Parameter 81 value is set to 54ºC by default. Any modification of

this parameter may cause the Fibaro Smoke Sensor not to work

within the valid safety regulations of your country.

VII. MALFUNCTION DETECTION

The Fibaro Smoke Sensor can automatically detect a malfunction. As described in

section V, the Fibaro Smoke Sensor performs a self test every 5 seconds. If a malfunction

is detected (e.g. damaged smoke chamber) an intermittent sound alarm will start, LED

diode will blink red and alarm will be sent to the Z-Wave network controller and

associated devices.

Once a malfunction has been detected, it’s recommended to:

• check the power source (replace battery or check VDC adapter’s voltage),

• check whether the Smoke Sensor is exposed to direct light.

If a malfunction is continually reported, it’s recommended to replace a the Fibaro Smoke

Sensor with new one.

Self test may be triggered manually:

1) Make sure the device is being powered.

2) Press and hold the B-button untill the LED glows white and short alarm sounds.

3) Keep holding the B-button for an additional 3 seconds from the first beep to check the

smoke chamber operation.

LED indicator colour changing to green and beep mean the positive result. If the LED

indicator changes its colour to red, the sensor is malfunctioning.

NOTE

Any service or repair must be carried out by the manufacturer.

VIII. DETECTING LACK OF Z-WAVE RANGE

When included in the Z-Wave network, Fibaro Smoke Sensor tests the network

communication. The Z-Wave network communication test is performed in both hard wired

and battery powering modes during every temperature report. By default, once the

ambient temperature changes by 2ºC, according to parameters 10 and 12 settings. In

addition, in battery mode, the Z-Wave network communication test is performed at device

polling. In constant power mode, the Z-Wave network communication test is performed in

time intervals defined by parameter 80 settings. Lack of the Z-Wave network communica-

tion is signaled by an intermittent alarm sound and LED blinking pink.

Once a Fibaro Smoke Sensor has reported no Z-Wave network communication, it’s

recommended to wake up the device by triple clicking the B-button. If it doesn’t stop the

alarm, Z-Wave networks operation and the main controllers operation need to be verified.

The Fibaro Smoke Sensor will cancel the Z-Wave network communication alarm once it

communicates with the network after manual or automatic wake up.

NOTE

It’s not recommended to deactivate the Z-Wave network communication

test.

IX. SENSOR’S SENSITIVITY LEVEL CONFIGURATION

There are 3 sensitivity levels of the optical smoke detector used in Fibaro Smoke Sensor.

By default, the detector is set to the middle sensitivity level. Sensitivity level depends on

the parameter 82 settings.

X. RESETTING THE FIBARO SMOKE SENSOR

The Fibaro Smoke Sensor reset erases the EPROM memory, including all information on

the Z-Wave network and the main controller.

Fibaro Smoke Sensor reset procedure:

1) Make sure the device has the power connected.

2) Press and hold the B-button for 3 seconds. LED will glow white.

3) Short signal will sound.

4) Release the B-button.

5) Wait until the LED glows yellow, signaling entering the 4th menu level.

6) Press the B-button briefly to confirm menu level choice.

Successful reset will be confirmed with the LED changing colour to red and fading. At the

same time, short beep will sound, same as at the power connection.

XI. OPERATING THROUGH THE Z-WAVE NETWORK

Fibaro Smoke Sensor has a built in smoke detector and a temperature sensor, which

makes it a multi channel device. In the Home Center 2 menu it will be presented as two

devices, depending on the main controller software version*:

Fig. 2 - Constant current or alarm system hub

connecting terminals installation.

AUX COM Z1 Z2

ALARM

SYTEM HUB

+12/24

GND

SMOKE

TAMP

12/24 VDC

ADAPTER

GND

+12/24

GND

SMOKE

TAMP

NOTE

It’s not recommended to change Fibaro Smoke Sensor’s sensitivity

level.

B - button

and LED indicator

TMP

NOTE

When the self test is triggered manually, the Fibaro Smoke Sensor sends

the command frame to the Z-Wave network controller and to the 1st

Association group devices. After 3 seconds from releasing the B-button,

the alarm cancelling command frame will be sent and the procedure will

be finished.

Installing Fibaro Smoke Sensor

1) Include the device into the Z-Wave network (see p.I). Note the inclusion process

may be performed ONLY in direct range of the main controller.

2) If the sensor is hard wired to power source, drill holes in sensor’s cover. Note the

sensor may be connected to a wired alarm system controller or fire prevention

system.

3) Install the sensor’s cover in desired location.

4) If the sensor is to be VDC powered, connect wires observing diagram # 3. If the

sensor is to be connected to an alarm system or fire prevention system, connect

it observing the diagram # 4.

* Depending on the parameters settings.

Drill holes here

NOTE

Device reset will not remove it from the Z-Wave network main

controller’s memory. Before resetting the device, it must be excluded

from the Z-Wave network.

XIX. GUARANTEE

XVIII. BATTERY USE WARNING

2. The Manufacturer is responsible for equipment malfunction resulting from physical

defects (manufacturing or material) of the Device for 12 months from the date of its

purchasing.

3. During the Guarantee period, the Manufacturer shall remove any defects, free of

charge, by repairing or replacing (at the sole discretion of the Manufacturer) any

defective components of the Device with new or regenerated components, that are free

of defects. When the repair impossible, the Manufacturer reserves the right to replace the

device with a new or regenerated one, which shall be free of any defects and its condition

shall not be worse than the original device owned by the Customer.

4. In special cases, when the device cannot be replaced with the device of the same type

(e.g. the device is no longer available in the commercial offer), the Manufacturer may

replace it with a different device having technical parameters similar to the faulty one.

Such activity shall be considered as fulfilling the obligations of the Manufacturer. The

Manufacturer shall not refund money paid for the device.

5. The holder of a valid guarantee shall submit a guarantee claim through the guarantee

service. Remember: before you submit a guarantee claim, contact our technical support

using telephone or e-mail. More than 50% of operational problems is resolved remotely,

saving time and money spent to initiating guarantee procedure. If remote support is

insufficient, the Customer shall fill the guarantee claim form (using our website

- www.fibargroup.com) in order to obtain claim authorization. When the guarantee claim

form is submitted correctly, the Customer shall receive the claim confirmation with an

unique number (Return Merchandise Authorization -RMA).

6. The claim may be also submitted by telephone. In this case, the call is recorded and

the Customer shall be informed about it by a consultant before submitting the claim.

Immediately after submitting the claim, the consultant shall provide the Customer with

the claim number (RMA-number).

7. When the guarantee claim form is submitted correctly, a representative of the

Authorised Guarantee Service (hereinafter as "AGS") shall contact the Customer.

8. Defects revealed within the guarantee period shall be removed not later than 30 days

from the date of delivering the Device to AGS. The guarantee period shall be extended

by the time in which the Device was kept by AGS.

9. The faulty device shall be provided by the Customer with complete standard

equipment and documents proving its purchase.

10. Parts replaced under the guarantee are the property of the Manufacturer. The

guarantee for all parts replaced in the guarantee process shall be equal to the guarantee

period of the original device. The guarantee period of the replaced part shall not be

extended.

11. Costs of delivering the faulty device shall be borne by the Customer. For unjustified

service calls, the Service may charge the Customer with travel expenses and handling

costs related to the case.

12. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without accessories or

nameplate,

• it was determined that the fault was caused by other reasons than a material or

manufacturing defect of the Device

• the guarantee document is not valid or there is no proof of purchase,

13. The Manufacturer shall not be liable for damages to property d by defective cause

device. The Manufacturer shall not be liable for indirect, incidental, special, consequen-

tial or punitive damages, or for any damages, including, inter alia, loss of profits, savings,

data, loss of benefits, claims by third parties and any property damage or personal

injuries arising from or related to the use of the Device.

14. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical deformations caused

by impact, falling or dropping the device or other object, improper use or not observing

the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire, lightning, natural

disasters, earthquakes, war, civil disturbance, force majeure, unforeseen accidents,

theft, water damage, liquid leakage, battery spill, weather conditions, sunlight, sand,

moisture, high or low temperature, air pollution;

• damages caused by malfunctioning software, attack of a computer virus, or by failure to

update the software as recommended by the Manufacturer;

• damages resulting from: surges in the power and/or telecommunication network,

improper connection to the grid in a manner inconsistent with the operating manual, or

from connecting other devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely adverse conditions, i.e.

high humidity, dust, too low (freezing) or too high ambient temperature. Detailed

permissible conditions for operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the Manufacturer

• damages caused by faulty electrical installation of the Customer, including the use of

incorrect fuses;

• damages caused by Customer's failure to provide maintenance and servicing activities

defined in the operating manual;

• damages resulting from the use of spurious spare parts or accessories improper for

given model, repairing and introducing alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

15. The scope of the guarantee repairs shall not include periodic maintenance and

inspections, in particular cleaning, adjustments, operational checks, correction of errors

or parameter programming and other activities that should be performed by the user

(Buyer). The guarantee shall not cover natural wear and tear of the Device and its

components listed in the operating manual and in technical documentation as such

elements have a defined operational life.

16. If a defect is not covered by the guarantee, the Manufacturer reserves the right to

remove such defect at its sole discretion, repairing the damaged or destroyed parts or

providing components necessary for repair or replacement.

17. This guarantee shall not exclude, limit or suspend the Customer rights when the

provided product is inconsistent with the purchase agreement.

Fig. 3 Smoke Sensor icon in

Home Center 2*

XII. ASSOCIATIONS

Through an association Fibaro Smoke Sensor may control another Z-Wave

network device, e.g. a Dimmer, Relay Switch, Roller Shutter, RGBW Controller,

Wall Plug, or a scene (scene only through the Home Center 2 main controller)

NOTE

Association allows for direct communication between Z-Wave

network devices. Main controller does not take part in such

communication. Using this mechanism, Fibaro Smoke Sensor

may communicate with other devices even when the main

controller is damaged, e.g. in a fire.

Fig. 4 Smoke Sensor icon

in Home Center 2

indicating the smoke alarm

and a tamper alarm*

Fibaro Smoke Sensor allows for the associations of three groups.

1-st Association Group is assigned to the device status - sending the BASIC SET

(default) or ALARM control frame to the associated devices having detected fire.

The type of alarm frame sent may be modified in advanced configuration

parameters (see section XVII).

2-nd Association Group is assigned to the TMP button and the malfunction alarm.

Alarm frame will be sent to the associated devices once tampering or malfunction

are detected.

3-rd Association Group reports the device status and allows for assigning a

single device only (the main controller by default - the device reports its status to

the main controller). It’s not recommended to modify this association group.

Fibaro Smoke Sensor allows for controlling 5 regular and 5 multichannel devices

per an association group, out of which 1 field is reserved for the Z-Wave network

main controller.

To add an association (using Home Center 2 interface) go to device settings and

click the following icon:

Select the “device options” tab. Then specify to which group and what devices are

to be associated. Sending relevant information to devices that have been added to

association group may take up to a few hours depending on the previous

configuration parameters’ settings.

NOTE

During the Z-Wave network range test, Fibaro Smoke Sensor is

not detecting smoke presence. Device resumes normal operation

once the Z-Wave network range rest has been finished.

XVI. BLACK BOX

The Fibaro Smoke Sensor has a built in memory for recording smoke and

temperature information. Having recorded even the smallest amount of smoke, the

sensor records the smoke level measured, time and temperature measured at that

precise moment. This information is sent to the Z-Wave network main controller

every 60 seconds. Home Center 2 allows for monitoring Black Box recordings (see

below figure). The Fibaro Smoke Sensor stops sending the Black Box records

once the smoke disappears, but a user can always access earlier reports through

the Z-Wave main controller. Black Box sensitivity may be modified through the

parameter 83 settings.

NOTE

Black Box gathers and sends the information even when there’s

no fire alarm.

XVII. ADVANCED CONFIGURATION

WAKE UP INTERVAL: (3 bytes)

Available settings: (5min – 24h)300 - 86399

Default setting: (each 4h)14400

When the Smoke Sensor is in battery power mode you can set up the wake up time

based in seconds. At each wake up, a the Smoke Sensor communicates with the

main controller, updates parameters settings and the software if necessary. The

Smoke Sensor will wake up at defined time interval and will ALWAYS try to

communicate with the main controller. After each failed communication attempt,

the sensor will retry to establish connection with the main controller after 60

seconds. After 3 failed attempts, the lack of the Z-Wave range alarm will be

triggered. The parameter is relevant for the battery powering mode only. Longer

time interval means less frequent communication and thus a longer battery life.

The Z-Wave range alarm will be cancelled automatically, after first successfull

connection.

NOTE

Parameter settings do not influence the visual and acoustic

alarms, which are turned off once the smoke has disappeared.

2. LED indicator and acoustic alarm turned ON / OFF at any alarm type.

Allows for deactivating the LED indicator and the acoustic alarm, in case of

detecting an alarm of any type. This doesn’t affect the communication with the

Z-Wave network controller, i.e. the sensor will keep sending alarms, reports and all

information to the associated devices. Modifying this parameter settings helps

extending the battery life.

Available settings: 0-3

0 – acoustic and visual alarms inactive

1 – acoustic alarm inactive, visual alarm active

2 – acoustic alarm active, visual alarm inactive

3 – acoustic and visual alarms active

Default setting: 3

Parameter size: [byte]1

NOTE

Deactivating the acoustic and visual alarms may result in

insufficient reporting of the smoke alarm. It’s not recommended to

modify this parameter settings.

5. Type of alarm frame sent to 1-st Association Group devices (smoke alarm).

Allows for choosing a command class used in 1-st Association Group.

Available settings: 0, 255

0 - ALARM SENSOR (SMOKE) command frame,

255 - BASIC_SET command frame.

Default setting: 255

Paramter size: [byte]1

7. Forced level of dimming / opening dimmers, roller blinds etc. devices at

sending turn on / open / change level commands to 1-st Association Group’s

devices.

The value of 255 allows for turning on a device. In case of Dimmer, the value of 255

means turning on the device with the last memorized state. E.g. Dimmer set to

30% and then turned off, and next turned on using the 255 command, will turn on

with the last remembered status, i.e. 30%.

In case of alarm frames, alarm priority is defined.

Available settings: or (1 - 99) 255

Default setting: 255

Parameter size: [byte]1

NOTE

2-nd association group alarms cannot be cancelled.

10. Temperature report interval.

Time interval between consecutive temperature reports.

The parameter is relevant for the battery powering mode only. Longer time interval

means less frequent communication and thus a longer battery life.

Report is sent when new temperatue value is different from the one previously

reported. Temperature reports can be also sent as a result of polling.

Available settings: (multiply by 5 seconds) [5s-24h]1 – 17280, 0

0 – reports inactive

Default setting: (Reports inactive)0

Parameter size: [bytes]2

12. Temperature report hysteresis.

The temperature report will only be sent if there is a difference in temperature value

from the previous value reported, defined in this parameter (hysteresis).

Temparature reports can be also sent as a result of polling.

Available settings: (in 0,1 0 – 100 oC steps)

0 – temperature change reporting inactive

Default setting: (220 oC)

Parameter size: [byte]1

NOTE

The parameter is relevant for the battery powering mode only.

Longer time interval means less frequent communication and thus

a longer battery life.

Available settings: (10min multiplier) [10min-24h]0 – 144

0 – Z-Wave network range test inactive

Default setting: 1 (10min)

Parameter size: 1 [byte]

81. Temperature alarm threshold.

Temperature value, measured by the built-in temperature sensor, above which the

temperature alarm is sent.

Available settings: 0,2 - 100

0 – temperature alarm inactive

2 - 100 – (2 - 100o

Default setting: (5454 oC)

Parameter size: [byte]1

NOTE

Any change in this parameter’s settings may cause a Fibaro

Smoke Sensor to operate contrary to valid safety regulations of

your country.

82. Fibaro Smoke Sensor sensitivity

There are 3 levels of sensitivity to smoke presence. Level 1 means the highest

sensitivity.

NOTE

Rising the parameter value lowers the sensitivity to smoke

presence. It’s not recommended to change this parameter’s

settings.

Available settings: 1 - 3

1 - HIGH Sensitivity

2 - MEDIUM Sensitivity

3 - LOW Sensitivity

Default setting: 2

Parameter size: [byte]1

83. Black Box sensitivity level.

This parameter allows for specifying the moment in which the Black Box starts

recording data. After the specified smoke and temperature values will be

exceeded, the Fibaro Smoke Sensor’s Black Box will record them.

Available settings: 1 - 3

1 - HIGH Sensitivity

2 - MEDIUM Sensitivity

3 - LOW Sensitivity

Default setting: 2

Parameter size: [byte]1

84. Malfunction alarm

Time interval in which malfuntion alarm, if detected, is repeated using visual and

acoustic alarms.

Available settings: (100 ms multiplier) [100ms-25,5s]1 - 255

Default setting: (1s)10

Parameter size: [byte]1

85. Temperature alarm

Time interval in which temperature alarm, if detected, is repeated using visual and

acoustic alarms.

Available settings: (100 ms multiplier) [100ms-25,5s]1 - 255

Default setting: (500ms)5

Parameter size: [byte]1

86. Lack of the Z-Wave range alarm

Time interval in which lack of the Z-Wave network alarm, if detected, is repeated

using visual and acoustic alarms.

Available settings: (5s multiplier) [5s-24h]1 - 17280

Default setting: (30min)360

Parameter size: [bytes]2

87. Low battery alarm

Time interval in which low battery alarm, if detected, is repeated using visual and

acoustic alarms.

Available settings: (5s multiplier) [5s-24h]1 - 17280

Default setting: (30min)360

Parameter size: [bytes]2

88. Consider temperature measurement compensation (parameter 73) when

sending temperature report.

Available settings: 0 - 1

0 - ignore temperature compensation

1 - include temperature compensation

Default setting: 0

Parameter size: [byte]1

XIII. LED VISUAL INDICATORS AND SETTINGS

The Fibaro Smoke Sensor is equipped with a LED diode for indicating, signaling

sensor’s operating modes and alarms. In addition the LED indicator may inform of

the Z-Wave network range and the current temperature.

LED indicator signaling modes:

1) Fire alarm is signaled by blinking in red.

2) Tamper alarm is signaled with a short blink in red.

3) Malfunction alarm is signaled by blinking in red.

4) Z-Wave network range alarm is signaled by blinking in pink.

5) Low battery alarm is signaled by blinking in yellow.

6) MENU levels are signaled with glowing in certain colour.

To enter MENU, press and hold the B-button for 3 seconds.

Once the LED glows white, release the B-button. LED will then start changing

colours in sequence. Each colour means different MENU level. Press the B-button

briefly to confirm choice. Transitions between the MENU levels will be signaled

with a short beep as well.

LED colours will change in the following sequence:

WHITE - entering MENU + self test

GREEN - refresh alarm state for the associated devices

PINK - Z-Wave communication test.

YELLOW - sensor reset.

13. Alarm broadcast.

A value other than 0 means that alarms are being sent in broadcast mode, i.e. to

all devices within a Fibaro Smoke Sensor’s range.

Available settings: 0 - 3

0 – broadcast inactive

1 – smoke alarm broadcast (1-st Association Group) active; tamper alarm

broadcast (2-nd Association Group) inactive

2 – smoke alarm broadcast (1-st Association Group) inactive; tamper alarm

broadcast (2-nd Association Group) active

3 – smoke alarm broadcast active (1-st association group); tamper alarm

broadcast (2-nd association group) active.

Default setting: 0

Parameter size: [byte]1

73. Temperature measurement compensation.

Parameter stores a temperature value to be added to or deducted from the current

temperature measured by internal temperature sensor in order to compensate the

difference between air temperature and temperature measured at the ceiling level.

Available settings: (in 0,1-1000 -/+ 1000 oC steps)

Default setting: (00oC)

Parameter size: [byte]2

80. Z-Wave range test interval.

Time period between the consecutive Z-Wave network range tests.

In battery powering mode, Z-Wave network range test is carried out at the wake up

interval. The value of 0 turns off the Z-Wave range test, regardless of the powering

mode chosen.

Fig. 5 Fibaro Smoke Sensor black box chart.

NOTE

During the Z-Wave network range test and during the software

update as well, Fibaro Smoke Sensor does not detect smoke

presence. Once the Z-Wave network range test and software

update is completed, the device resumes normal operation.

NOTE

Any change in this parameter’s settings may cause a Fibaro

Smoke Sensor to operate contrary to valid safety regulations of

your country.

89. Tamper alarm

Available settings: 0, 1, 2

0 – tamper alarm inactive

1 – tamper alarm active, with cancellation option available

2 – tamper alarm active, without cancellation option

default setting: 1

parameter size: [byte]1

Black Box recordings are stored for about 24 hours, depeding on

the parameter 83 settings and working environment conditions.

User may force sending these recordings to the Z-Wave network

main controller, depending on its model and software version.

XIV. CANCEL ALARM FOR ASSOCIATED DEVICES

The Fibaro Smoke Sensor automatically cancels smoke alarms sent to the Z-Wave

network controller and the associated devices. It’s possible to delay or deactivate

the alarm cancellation by modifying parameter 1 settings. In such a case, once an

alarm is detected, it will be constantly reported unless manually cancelled by

choosing green MENU level.

Fibaro Smoke Sensor is a battery-powered device. Using batteries other than

specified may result in explosion. Dispose of properly, observing environmental

protection rules.

NOTE

Tamper alarms cannot be cacelled through MENU.

XV. Z-WAVE RANGE TEST

The Fibaro Smoke Sensor has a built in Z-Wave network main controller’s range

tester. Follow the below instructions to test the main controller’s range:

1) Make sure the sensor is powered.

2) Press and hold the B-button for 3 seconds. LED will glow white.

3) Short signal will sound.

4) Release the B-button.

5) Wait untill the LED glows pink, and then press the B-button briefly to start the

test.

6) LED will indicate the Z-Wave network’s range (range signaling modes described

below).

7) To exit Z-Wave range test, press the B-button brefly.

Z-Wave range tester signaling modes:

LED indicator pulsing green - Fibaro Smoke Sensor attempts to extablish a

direct communication with the main controller. If a direct communication attempt

fails, sensor will try to establish a routed communication, through other modules,

which will be signaled by LED indicator pulsing yellow.

LED indicator glowing green - Fibaro Smoke Sensor communicates with the

main controller directly.

LED indicator pulsing yellow - Fibaro Smoke Sensor tries to establish a routed

communication with the main controller through other modules.

LED indicator glowing yellow - Fibaro Smoke Sensor communicates with the

main controller through the other modules. After 2 seconds the sensor will retry to

establish a direct communication with the main controller, which will be signaled

with LED blinking in green.

LED indicator pulsing violet - Fibaro Smoke Sensor communicates at the range

limit. If connection proves successful it will be confirmed with a yellow glow. It’s not

recommended to use the sensor at the range limit.

LED indicator glowing red - Fibaro Smoke Sensor is not able to connect to the

main controller directly or through another Z-Wave network nodes.

This Device may be used with all devices certified with Z-Wave

certificate and should be compatible with such devices produced

by other manufacturers.

Any device compatible with Z-Wave may be added to Fibaro system.

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre in your country.

www.fibargroup.com

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o. (hereinafter

"Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421 Poznan, entered in the

Economic Department of the National Court Register, no. 370151,

NIP 7811858097, REGON: 301595664.

0 - no delay, immediate cancellation

65535 - alarm cancellation inactive - Smoke Sensor will keep indicating smoke

alarm after the smoke will have disappeared. The smoke alarm can be only ceased

manually, by entering 2nd menu level (see section XIII).

Default setting: 0

Parameter size: [bytes]2

NOTE

Default value of the Wake Up, in Home Center 2, is 6 hours.

1. Smoke alarm cancellation delay

The time between when the smoke disappears and the Fibaro Smoke Sensor

stops sending the alarm signal.

Available settings: (5s multiplier) [5s-24h]0 – 17280, 65535

Product specificaties

Merk:	Fibaro
Categorie:	Rookmelders
Model:	FGSS-001
Kleur van het product:	Aluminium, White
Hoogte:	28 mm
Stroombron:	AC/DC
Connectiviteitstechnologie:	Draadloos
Montagewijze:	Opbouwmontage
Diameter:	65 mm
Certificering:	EMC 2004/108/EC, R&TTE 199/5/WE
Maximumbereik:	50 m
Detector type:	Optische detector
Licht alarm:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Test knop:	Ja