Festo DARD-L8-32-S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Festo DARD-L8-32-S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Translation of the original instructions
LOCTITE 243Ž is a registered trademark of its respective trademark holder in cer
tain countries.
1 Further applicable documents
All available documents for the product www.festo.com/pk.è
Observe further applicable documents:
– Operating instructions of the linear drive5
2 Safety
2.1 Safety instructions
– Before working on the product, switch off the power supply and secure it
against being switched on again.
– Observe tightening torques. Unless otherwise specified, the tolerance
is±10%. Tightening torques 5 Technical data.è
– Observe the safety data sheet for the adhesive from the original manufac
turer.
2.2 Intended use
Compensating element between the slide(A) of the linear drive and the pay5
load to be moved.
3 Product range overview
3.1 Scope of delivery
1Moment compensator (1x)
2Adhesive LOCTITE 243 (1x)
3Threaded pin (1x)
4Screw (3x)
Fig. 1
3.2 Not in scope of delivery
5Linear drive DLGFG (1x)
Fig. 2
4 Mounting
Positioning the moment compensator
Fig. 3
• Place the moment compensator opposite the sensor slot(X) flush with the1
slide(A).
ÄThe sensor slot(X) is freely accessible.
Attaching the moment compensator
Fig. 4
• Use the screws to attach the moment compensator to the slide(A). Do4 1
not tighten screws .4
Mounting the moment compensator
Fig. 5
1. Apply adhesive to the threaded pin .2 3
2. Screw the threaded pin into the moment compensator .3 1
3. Tighten the threaded pin .3
4. Tighten the screws .4
4.1 Mounting the payload
Hole for spring pin(B)
Fig. 6
• Hole for spring pin(B) provided for centring the payload.
Recommended hole for spring pin(B): 5.2Æ+0.1mm
Mounting the payload on DARD-L8-20/25-S
Fig. 7
• Mount payload with recommended screws using hole(C) or(D) on the
moment compensator .1
Hole(C) Hole(D)
Hole thread M5 M5
Recommended screws 2xM58.8 2xM48.8 ISO4762ß
Recommended tightening torques [Nm] 4.5 2.6
Tab. 1
When mounting the payload using hole(D), the threaded holeM5(C) serves as a
through hole for the screwM4.
8084730
Moment compensator
DARD-L8
8084730
201802a
[8084732]
Instructions| Assembly
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 3470
www.festo.com
Mounting the payload on DARD-L8-32/40-S
Fig. 8
• Mount payload with recommended screws using hole(E) or(F) on the
moment compensator .1
Hole(E) Hole(F)
Hole thread M5 –
ß 2xM58.8 2xM410.9
ISO4762
Recommended screws
Recommended tightening torques [Nm] 5 3.7
Tab. 2
5 Technical data
5.1 Screw sizes and tightening torques MA
DARD-L8 20 25 32 40
ß M4x18 M4x18 M4x22 M4x224Screw
ISO4762 [Nm] 3 3 3.4 3.4
3 Threaded pin [Nm] 1 1 1 1
Tab. 3


Product specificaties

Merk: Festo
Categorie: Niet gecategoriseerd
Model: DARD-L8-32-S

Heb je hulp nodig?

Als je hulp nodig hebt met Festo DARD-L8-32-S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Festo

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd