Extron TLM 100T Handleiding

Extron Niet gecategoriseerd TLM 100T

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron TLM 100T (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Product Category

TLM 100T • Installation Guide

The TLM 100T is a secure tabletop mounting enclosure

for an iPad® in a landscape orientation. The enclosure is

compatible with the iPad 2, iPad 3, and iPad 4.

Installing an iPad in a TLM 100T

1. Use the provided Extron removal tool to ease

the faceplate away from the back panel. Start by

releasing the catches at the bottom and gradually

work around the sides until the faceplate lifts off.

2. Remove the metal frame.

3. Remove the base cover, using the Extron removal

tool.

4. Run the iPad charging cable through the hole at the

bottom of the TLM 100T back panel, then through

the cable raceway in the base of the unit, and out

the back of the base.

NOTE: Leave about 1½ inches (3.8 cm) of

charging cable free to connect to the iPad.

5. Place the iPad in the rear enclosure. The power switch must be in

the top left corner.

6. Place the metal frame with the rubber pads in contact with the iPad.

7. Use the provided #6 spanner bit and the eight provided spanner

drive screws to secure the metal frame.

ATTENTION: Do not overtighten the screws.

8. Replace the faceplate. Ensure it is in the correct orientation with the

Extron name at the bottom.

9. Replace the TLM 100T base cover.

Tabletop Mounting Options

Securing the TLM 100T to a Tabletop

The TLM 100T can stand on any convenient tabletop. If required, use two screws in the two mounting holes in the base to secure

the unit to the desktop (see the gure at right).

1. Drill two holes through the desktop. The two holes must be 3.07inches (78 mm) apart and 3/8 inch (9.5 mm) in diameter.

2. Fasten the base to the desktop with two #8 wood screws (not provided) through

the desktop from underneath into the two holes in the base of the TLM 100T.

Installing the TLM 100T on an SMA-1 Swivel Mount

The TLM 100T can be mounted with the Extron SMA-1 swivel mount adapter,

allowing it to swivel up to 359° (see the SMA-1 Swivel Mount Adapter Kit User Guide

at www.extron.com).

1. Determine where the SMA-1 and TLM 100T are to be mounted.

2. Mount the SMA-1 and congure the set screws as described in the SMA-1

Swivel Mount Adapter Kit User Guide.

3. Remove the rear and base covers of the TLM 100T, using the Extron removal

tool.

4. Remove the hole plug from the base of the TLM 100T to reveal the mounting

hole.

TLP 100T rear view with

the base cover removed.

Spanner Drive Screws (8)

secure the metal frame to

the TLM 100T back panel.

TLM 100T Faceplate

snaps to unit (11 plcs.)

Power Switch

iPad

TLM 100T

Back Panel.

TLP 100T Base View

Hole Plug for

SMA-1 mounting

Mounting Holes

for sc ws (2)re

Product specificaties

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	TLM 100T
Kleur van het product:	Zwart
Gewicht:	1200 g
Breedte:	283 mm
Diepte:	186 mm
Hoogte:	228 mm
Compatibiliteit:	iPad (2nd, 3rd, 4th gen)
Maximale schermgrootte:	9.7 "