Extron QC 101 C Handleiding

Extron Niet gecategoriseerd QC 101 C

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron QC 101 C (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

QC 101 Controller • Setup Guide

This setup guide provides basic instructions for an

experienced user to install the QC 101 Controller. For

additional information and detailed procedures, see

the and the Quantum User Guide Quantum Control

Software User Guide, available at www.extron.com.

The Extron QC 101 E and QC 101 C are dedicated

controllers for the Quantum® Elite and Quantum

Connect videowall processors. They feature an

embedded operating system and the Quantum Control

Software preinstalled on the internal drive. The QC 101

provides an alternative to a traditional PC to program

congurations and control the Quantum processors.

ATTENTION:

• All structural steps and electrical installation must be performed by qualied personnel in accordance with local and

national building codes and electrical codes.

• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualié, conformément aux codes

du bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

NOTE: For full installation, configuration, and operation details, see the , which is provided with the Quantum User Guide

Quantum on the Extron Videowall Processing disc and is also available at www.extron.com.

Rear Panel Features and Connections

AAA

100-240V ~ 0.5A MAX

50-60Hz

DISPLAYPORT 1

A B RGBHV

RS-232

Tx Rx G

RESET

HDMI

OUTPUTS

USB LAN OUTPUTS

REMOTE

B C D E F

POWER

Figure 1. QC 101 Rear Panel

A AC power connector — Connect to an AC power

source.

B DisplayPort output connector — (Optional)

C USB connectors — Connect to a mouse, keyboard,

or flash drive. Connector 1 (top) accepts USB 2.0

signals and connector 2 accepts USB 3.0.

D A and B LAN ports — Connect to a network or the

Quantum processor. These two RJ-45 connectors

support 10/100/1000 Base-T.

E RGBHV output connector — (Optional) 15-pin VGA

F Remote RS-232 connector — Connect to a control

system for RS-232 communication.

G Power button — Using a small screwdriver or stylus,

press this recessed button momentarily to safely shut

down the controller. Pressing and holding the button for

4 seconds forces a hard shutdown of the QC 101.

H HDMI output connector — (Optional)

NOTE: The button and LED labeled RESET are not functional.

Installation Steps

1. Disconnect power from all equipment.

2. (Optional) Mount the unit to a rack or furniture, following the instructions provided with the mounting hardware. Rack

and furniture mounting kits are available at www.extron.com.

3. Connect a display to the DisplayPort, VGA, or HDMI output connector (see gure 1,

B, E, or H).

QC 101 • Setup Guide (Continued)

4. Connect the keyboard, mouse, and flash drive (if needed) to the rear panel USB ports (

C) to create and save Quantum

Elite or Connect configuration project files (see the , available at Quantum Control Software User Guide www.extron.com).

5. Connect a straight-through Ethernet cable between QC 101 LAN port A or B (see ﬁgure 1,

D, on the previous page)

and the network or the Control connector on the rear panel of the Quantum chassis. If connecting through a LAN, ensure that

the QC 101 is on the same subnet as the Quantum processor or processors.

6. Connect a control device (such as an Extron IPCP or IPL Pro) to the Remote RS-232 port (F) for remote

control of the Quantum system using R-type commands (see the , available at Quantum Control Software User Guide

www.extron.com, for more about these commands).

7. Connect AC power to the QC 101 rear panel IEC connector (see A). Connect power to all other devices in the system.

8. Power on the Quantum chassis and all other connected devices.

100-240V ~ --A MAX

50/60 Hz

OUT PUT S

REMOT E

US B LAN

DIS PLAYPO RT

A B RGBHV

RS232

T x Rx G

RESET PO WER

HDM I

Control

VLAN

Ethernet

RS-232

HDMI

USB USB

Mouse

Display

Keyboard HDMI

Extron

Quantum t Connec

HDCP ompliant-C l Vide alow

Processin Systg em

Ext

ron I o 0PCP Pr 25

IP ink L o l Pr Contro Processor

Extron

QC 1 C10

Controller for

Quantum Connect QUANTUM CO NNECT 408

VIDEO WALL PROCESS OR

DATA

1000

LINK

ACT

RIR

IPCP PRO 250

eBUS

OVER

LIMITS

COM

I/O

321

RT S

CT S

T x

RELAYSIR/S

Sources

Displays

Figure 2. QC 101 Connection Example with a Quantum Connect

NOTE: The QC 101 front panel has no controls that are involved in setup. It contains four indicator LEDs that provide status

for power and booting (Power), disk drive activity (SSD), and network activity (LAN A and LAN B). The USB Config port is

reserved for future use.

Conﬁguring the QC 101

After all rear panel connections have been made and all connected devices are powered on, you are ready to congure the

QC 101 to manage the Quantum processors. To do this, set the IP address of the QC 101, then either create a project le using

the Quantum Control Software (loaded on the QC 101 prior to delivery) or upload an existing project le that was congured using

a computer.

Setting the IP Address of the QC 101

The QC 101 controller is a host device with an embedded operating system. To communicate with the Quantum processor, the

QC 101 must be on the same network and subnet as all the Quantum processors in the system. To set the QC 101 IP address,

you need a keyboard and mouse connected to one or both of the USB ports and a monitor connected to one of the output ports.

1. Do either of the following:

zOn the QC 101 screen, click the icon (shown at right), or

zOn the desktop screen, double-click the shortcut icon on the desktop.

The window opens.

2. Right-click the name of the LAN port in use (highlighted and no red ) and select from the pop-up menu.

Figure 3. Selecting a LAN Port

3. On the window, scroll to locate and select the

checkbox (see 1 in

the illustration at right), and click (2).

4. In the Internet

window, enter the desired QC 101 IP address parameters and click

. The IP address must be on the as those of the same subnet

Quantum processors.

5. In the window (which opened at the same time as the

window in step 1), click the

button (see gure 4, 1).

Figure 4. Click Commit C Drive on the QC 101 Shell Window

6. On the conrmation prompt that opens, click to save the address changes to the hard drive and reboot the controller. A

password prompt is displayed. Enter the password where indicated on the prompt and click .

ATTENTION:

• Do not power off or reset the QC 101 while it is rebooting.

• Veuillez éteindre ni réinitialiser le QC 101 lors du redémarrage.ne pas

Setting Up the Quantum Control Software

To use the Quantum software to congure and control the processor, start by setting up a project (presentation), in which you

dene the processor, select or create a layout, set up video sources, and create multiple scenes.

NOTE: The C: drive on the QC 101 is write-protected. Therefore, files located on the C: drive that are created or changed are

not saved when power is cycled to the QC 101. Save any new or changed projects on the controller to the QC 101 internal

D: drive or to a flash drive attached to one of the USB ports on the QC 101 rear panel.

1. Create a new project or upload an existing one.

zIf creating a new project, see the for detailed instructions. Save the project to Quantum Control Software User Guide

the QC 101 D: drive and double-click its lename to open the project.

zIf uploading an existing project that was created on a PC, copy the project le directly to the QC 101 D: drive and

double-click its lename to open the project.

Product specificaties

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	QC 101 C
Kleur van het product:	Zwart
Gewicht:	1500 g
Breedte:	221 mm
Diepte:	305 mm
Hoogte:	42 mm
Gewicht verpakking:	2180 g
Breedte verpakking:	411 mm
Diepte verpakking:	295 mm
Hoogte verpakking:	137 mm
Frequentie van processor:	2.42 GHz
Processorfamilie:	Intel® Celeron®
Inclusief besturingssysteem:	Windows Embedded 8
USB-connectortype:	Mini-USB
Ethernet LAN:	Ja
Geïntegreerde geheugenkaartlezer:	Nee
Aantal USB 2.0-poorten:	1
VGA (D-Sub)poort(en):	1
Aantal HDMI-poorten:	1
Microfoon, line-in ingang:	Nee
DVI-poort:	Nee
Aantal Ethernet LAN (RJ-45)-poorten:	2
Aantal USB-aansluitingen:	1
Certificering:	CE, c-UL, UL, FCC Class A, ICES, VCCI
Netvoeding:	16 W
Intern geheugen:	4 GB
Opslagmedia:	SSD
Intern geheugentype:	DDR3-SDRAM
Aantal DisplayPorts:	1
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Bekabelingstechnologie:	10/100/1000Base-T(X)
Temperatuur bij opslag:	-40 - 70 °C
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	1
Architectuur besturingssysteem:	64-bit
Maximum intern geheugen:	4 GB
Totale opslagcapaciteit:	80 GB
Soort optische drive:	Nee
Ingebouwde grafische adapter:	Ja
Aparte grafische adapter:	Nee
On-board graphics adapter model:	Intel® HD Graphics
Luchtvochtigheid bij opslag:	10 - 90 procent
Discreet grafische adapter model:	Niet beschikbaar
Aantal geïnstalleerde SSD's:	1
SSD capaciteit:	80 GB
Type behuizing:	2L maat pc
Aantal geïnstalleerde processoren:	1
Aantal storage drives geïnstalleerd:	1
Inclusief monitor:	Nee
Voeding, voltage ingang:	100 - 240 V
Wifi:	Nee
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Type product:	Ingebouwde pc
Ingangsfrequentie voeding:	50 - 60 Hz
Waterkoelingsysteem:	Nee
RS‐232/422-poort:	Ja