Extron MediaPort 200 Handleiding

Extron Niet gecategoriseerd MediaPort 200

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron MediaPort 200 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

IMPORTANT:

Go to www.extron.com for the complete

user guide,

installation instructions,

and

specifications bef

ore connecting the

oduct to the po

wer source.

MediaPort 200 HDMI and Audio to USB Scaling

Bridge • Setup Guide

The MediaPort 200 is an HDMI and audio to USB scaling bridge that interfaces between pro AV equipment and computer-based

video conferencing software. Incoming HDMI video is scaled and output via USB to a host computer. Bi-directional audio is

supported over the USB bus, including two stereo pairs from the PC for application playback and far-end communication audio,

and one stereo pair to the PC for local audio to be sent to the far end. Digital and analog audio inputs and outputs include a full

range of DSP optimization features, including filtering, EQ, ducking, compressors, and limiters. Setup and control are available via

front panel controls with an LCD menu, a front panel USB Configuration port, a rear panel RS-232 port, and a rear panel Ethernet

port. SIS™ (Simple Instruction Set™) commands and Windows®-based software configuration simplify initial configuration and real-

time control. The 1U high, half rack wide, 9.5 inches (24.1 cm) deep enclosure can be optionally mounted to a rack shelf, or under

or through furniture.

This setup guide provides step-by-step instructions for an experienced user to set up and configure a MediaPort 200.

NOTE: For full installation, configuration, menu, connector wiring, and operation details, see the , MediaPort 200 User Guide

available at www.extron.com.

Installation

Rear Panel Features

MediaPort 200

100-240V 0.4A MAX

50-60 Hz

HDMI

LOOP OUT

MIC/LINE

+48V

LINE

L R LINE

L R

REMOTE

OUTPUT

LAN

USB

REF AUX

RESET

RS-232 +12V

I/O

0.1A

MAX

Rx G

I1 I2 G O1 O2

INPUT

GGDD

AA EE KK

A AC power connector F AEC REF and AUX audio output J Reset button

B HDMI video input connector connector K LAN connector

C HDMI video loop out connector G Line level audio output L RS-232 and +12 V power

D Line level audio input connector connector connector

E Mic/Line audio output connector H USB host connector M Digital I/O connector

and phantom power LED I Reset LED

Figure 1. MediaPort 200 Rear Panel

Mounting and Cabling the MediaPort 200

1. Disconnect power — Turn off or disconnect all equipment power sources.

2. Mount the unit — (Optional) Mount the MediaPort 200 either in a rack using shelf mounting brackets such as Extron

RSU 129 or RSB 129, or under furniture using furniture mounting brackets (MBU 125). A false half-rack plate can t next to

the unit if desired.

3. Connect the HDMI input — Connect an HDMI video source to the HDMI input connector (see gure 1, B). Use the

included LockIt® brackets to secure the connector in place.

4. Connect analog audio input —

zConnect an analog audio

input source to the 5-pole

captive screw Line audio input

connector (D) for balanced or

unbalanced stereo audio. Wire

as shown at right.

zConnect a balanced or unbalanced microphone or

mono line level input to the 3-pole Mic/Line captive

screw connector (E). Wire as shown at right. Balanced Audio Output Unbalanced Audio Output

Tip

Slee

Ring Tip

Sleeve

Unbalanced Stereo InputBalanced Stereo Input

Tip

Ring

Tip

Ring

Slee sve

Do not tin the wires!

Tip

Sleeve

Tip

L R

inch (5 mm)

MAX.

MediaPort 200 • Setup Guide (Continued)

5. Connect the USB output — Connect a USB type A to B cable from the rear panel bidirectional USB B port (see ﬁgure 1,

H) to a USB type A port of a PC or Mac computer for video and audio input and output. The USB Host LED lights when this

connection is made.

6. Connect to the HDMI loop output — (Optional) Connect a local monitor or a video conferencing hardware device to the

HDMI Loop Out connector (C).

7. Connect audio output — Connect

an amplier or other output device

to the 5-pole captive screw Line

output connector (G) for balanced

or unbalanced, stereo or dual mono,

analog program output. Wire as shown at right.

8. Connect devices for configuration and control —

zRS-232 — For serial control, connect a host computer or other

control device to the Tx, Rx, and G pins of the 5-pole RS-232

and +12 V captive screw connector (L). Wire as shown at

right.

z+12 V power — (Optional) Connect a device requiring DC

power (such as a digital I/O device that illuminates LEDs for

a microphone or switch plate) to the + and – pins of the 5-pole

control connector (L).

zUSB Config — Connect a host computer to the front panel

USB mini B port (see gure 2, C, below) for conguration via

SIS commands or the Extron PCS software.

9. Connect the MediaPort to the network — Connect an Ethernet

cable between the LAN port (see gure 1, K) and the network to

congure and control the MediaPort from a remote location using

SIS commands, the PCS software, or the embedded Web page.

10. Connect an AEC reference (optional) — Connect the +, –, and

¤ (ground) REF pins of the 5-pole REF/AUX connector (F) to an

external DSP processor to use as the reference for acoustic echo

cancellation. The Ref output matches the audio received via the

USB communication input (far end audio) to the USB communications input.

11. Connect an auxiliary device — (Optional) Connect the Aux +, –, and (ground) pins of the ¤

REF/AUX connector (F) to an external DSP processor or a video conferencing hardware device, to

which mic/line audio will be sent. The Aux output matches the audio applied to the Mic/Line input.

12. Connect devices to the Digital I/O ports — (Optional) Connect a microphone or other contact closure or tally device to

the 5-pole Digital I/O captive screw connector (M). The digital input ports are labeled I1 and I2. The output ports are O1 and

O2. The middle pin, labeled G, is the shared ground. Wire inputs to

pins I1 and I2 and outputs to pins O1 and O2. Connect the ground

wires of all devices to the G pin (see the illustration at right).

13. Connect power to the MediaPort 200 AC power connector (A).

14. Apply power to all connected devices.

Front Panel Overview

MediaPort 200

CONFIG

ADJUST

HDMI

SIGNAL IN

HDCP IN

LOOP OUT

LOOP HDCP

USB

HOST

VIDEO SEND

AUDIO SEND

AUDIO RETURN

AA BB CC DD

Figure 2. MediaPort Front Panel

USB Config port C

USB LEDs E Menu button G

Next button

B HDMI LEDs D

LCD screen F Adjust knobs

RS-232

Computer

RS-232 Po

MediaPort 200 Rear Panel

RS-232 Port

NOTES:

• If you use cable that has a drain wire, tie

the drain wire to ground at both ends.

Connect a ground wire between the

•

MediaPort and the computer.

1 2 3

Tx Rx G

+12V

+ –

Ground (G)

Transmit (Tx)

Receive (Rx) Transmit (Tx)

Receive (Rx)

REF XAU

REF

AUX

Input 1 (I1)

Input 2 (I2)

Ground (G)

Output 1 (O1)

Output 2 (O2)

I/O

Do not tin the wires!

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Slee sve

L R

A — Connect a computer to this USB mini B port for device configuration. USB Config port

B — These four LEDs light to indicate the HDMI input and loop output connection and HDCP status.HDMI LEDs

zSignal In — An active HDMI input signal is present.

zHDCP In — An HDCP encrypted input signal is being received.

zLoop Out — A sink is detected on the HDMI loop out connector.

zLoop HDCP — The signal out of the HDMI loop out is HDCP encrypted.

C — These four LEDs light to indicate the connection and signal status of the rear panel USB port.USB LEDs

zHost — The rear panel USB port is connected to and enumerated with the host computer.

zVideo Send — A video signal is being output to the host via USB.

zAudio Send — An audio signal is being output to the host via USB.

zAudio Return — Audio input is being received from the host via USB playback, communication, or both.

D — This LCD window displays menus, messages, and your selections from menus and submenus. LCD screen

E — Press this button to access the menu system and step through the menus on the LCD screen (Menu button D).

F — Rotate these horizontal ( ) and vertical ( ) rotary encoders to scroll through submenu item values Adjust knobs [ {

and make adjustments to your selections.

G — Press this button to step through the submenus displayed on the LCD screen when a menu is selected.Next button

Locking the Front Panel (Executive Mode)

To prevent unauthorized access or accidental changes to MediaPort settings, you can lock the front panel controls as follows,

making control available only by SIS commands and the PCS software.

zUsing the front panel buttons: lock To , press the and buttons simultaneously and hold them until the LCD

screen displays (approximately 5 seconds). To , press and hold the same buttons until unlock

the LCD screen displays . The default state is Unlocked.

zSIS commands: lock To (enable executive mode), enter using Extron DataViewer or other communication tool on your

host computer. To (disable executive mode), enter .unlock

Conﬁguring the MediaPort 200

The MediaPort 200 can be configured through a host connected to the LAN or the front panel USB Config port using Extron PCS

software, or to the RS-232, LAN, or front panel USB Config port using SIS commands. Common settings and statuses can be

viewed or changed via the LCD menus.

Using the LCD Menu System

The front panel LCD screen displays eight menus: Setup, , , ,

, , , and (read-only).

1. Press the button to access the menu system, then press it repeatedly to navigate to the desired menu.

2. Press the button to navigate to the desired menu item.

3. Rotate the horizontal ([) or vertical ({) knobs to cycle through the values for the selected item until the desired value

is displayed. For menu items, rotate the

[ (left) knob to adjust the value displayed at the left side of the

LCD screen and the { (right) knob to adjust the value at the right side.

4. To exit the menu system, press the button until appears, then press . The default cycle

is displayed. Alternatively, wait for the menu system to time out and return to the default cycle (approximately 30 seconds).

To edit the communication settings, navigate to the menu, then press and hold until

is displayed on the LCD screen (approximately 5 seconds). Press to navigate through the menu

Setup Items on the LCD Quick Setup Menu

Select and adjust the following LCD menu items to set up the MediaPort.

zAuto-Image™ — Performs an Auto-Image on the video input to adjust the horizontal and vertical size and positioning to the

selected aspect ratio (ll the screen or follow the input device aspect ratio). To perform an Auto-Image, select this item, then

press again to initiate the process. Follow the instructions on the LCD screen to complete the Auto-Image.

zHDMI Input EDID — Lets you select the Extended Display Identication Data (EDID) for the input. Default is .

zAspect Ratio — Controls how input signal aspect ratios will be compensated Rotate either encoder to select (lls the

entire output raster) or (the aspect ratio of the input signal is maintained relative to the output raster).

zTest Pattern — Lets you choose a test pattern to aid in setting up the MediaPort and the connected computer. Rotate either

Adjust knob to select a pattern: (no test pattern), , , , , and .

Product specificaties

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	MediaPort 200
Soort bediening:	Rotary, Buttons
Kleur van het product:	Zwart
Gewicht:	1400 g
Breedte:	221 mm
Diepte:	216 mm
Hoogte:	42 mm
Gewicht verpakking:	1810 g
Breedte verpakking:	356 mm
Diepte verpakking:	381 mm
Hoogte verpakking:	127 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
AC-adapterfrequentie:	50/60 Hz
AC-adapter ingangsspanning:	100 - 240 V
Type verpakking:	Doos
Ondersteunde video-modi:	480i, 480p, 576i, 720p, 1080i, 1080p
Certificering:	CE, c-UL, UL, C-tick, FCC Class A, ICES, VCCI, WEEE
Ingang stroom:	Ja
Audio-ingangen:	2
Audio-uitgang:	2
Ondersteunde grafische resoluties:	640 x 480 (VGA), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA)
Duurzaamheidscertificaten:	RoHS
Digitale verticale frequentie:	15 - 30 Hz
Temperatuur bij opslag:	-40 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
Rack-montage:	Ja
Frequentiebereik:	20 - 20000 Hz
RJ-45 ports hoeveelheid:	1
Signaal/ruis-verhouding:	90 dB
Crosstalk (1kHz):	90 dB
HDMI in:	2
RS-232 uitgangspoorten:	1
Warmtedissipatie:	59.2 BTU/h
Rackcapaciteit:	1U
Stroomverbruik (typisch):	18.9 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Geschaalde resoluties:	320 x 180,320 x 240,424 x 240,640 x 360,848 x 480,960 x 540,640 x 480
Maximale pixelsnelheid:	165 MHz
Baudrate:	9600 Bd