Extron DVS 304 DVI D Handleiding

Extron Niet gecategoriseerd DVS 304 DVI D

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron DVS 304 DVI D (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

The Extron DVS 304 Series of video and RGB digital scalers incorporate advanced technology

to provide high performance video processing with selectable output rates up to 1920x1200

(DVI models only) and HDTV 1080p, as well as simultaneous DVI (DVI models only) and

analog RGB or component video outputs.

This setup guide allows quick and easy set up and conguration of a DVS scaler using step by step instructions. It covers

performing basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.

N For full installation, conﬁguration, and operation details, refer to the DVS 304 Series User’s Manual, online at www.extron.com.

Installation — Rear Panel Features (DVS 304 DVI AD model shown)

INPUTS TOUTPU RS-232

LAN

RESET

ACT LINK

50/60 Hz

100-240V .3A

21 3 4L R L R

L RL RL R

AUDIO

VID

12 3

/VID

R-Y H/

/R-Y

/B-Y

DVI-I

SDI B-Y

RGB/R- B-Y/YC/VIDY, Y,

7 4 5 91 2 11

8 10

DVS 304 I ADDV

Power and video input connections Output and control connections

a AC power connector Audio output connectors - (audio models only)g

b Audio input captive screw connectors (inputs 1 to 4) - audio models only RGB/YUV-HD BNC and DVI* output connectorsh

c i Composite video BNC connector (input 1) Reset button and LED

Ñ j (Optional) SDI BNC connectors (congurable) RJ-45 Ethernet connector

d k Composite video/S-video/component video BNC connectors (input 2) 9-pin D RS-232 connector

e S-video 4-pin mini-DIN connector (input 3)

f 15-pin HD connector (input 4) with EDID emulation*

Installation and cabling

Step 1 — Mount the DVS

Turn off or disconnect all equipment power sources and rack mount the DVS unit, using

suitable mounting brackets or rack shelf (see image at right).

Refer to the DVS 304 Series User’s Manual for details.

Step 2 — Connect inputs

Connect inputs from video and/or audio sources to the applicable connectors marked

“Inputs” (see above for connector types). See diagrams below for signal format on BNC b to f

connectors and audio input captive screw wiring (balanced or unbalanced, mono or stereo).

N When connecting a VGA input to a DV 304 DVI model, by default the EDID emulation is set to match the current output rate. To set to a speciﬁc rate,

or set to a display's EDID rate, or to upload a custom EDID table refer to the , available at DVS 304 Series User’s Manual www.extron.com.

Component video

(Y, R-Y, B-Y) S-video Composite video

B-Y

/VID

R-Y

B-Y

/VID

R-Y

B-Y

/VID

R-Y

Input 2

Input 4

Pin 1

15-HD pins Pin 2 Pin 3 Pin 13 Pin 14

Input source

BNC’s

R VHB

RGB

RGBcvS

YUV

S-video

Composite video

R G(S) B H V

RGBcvS

R-Y YB-Y

DVS 304 Series – Setup Guide

Rack Mount

Bra tcke

Unbalanced Stereo Input

Tip

Sleeve

Tip

L R

Unbalanced Mono Input

Balanced Mono Input

L R

Tip

Ring

Sleeve

Tip

Ring

L R

Tip

Sleeve

Tip

Sleeve

Balanced Stereo Input

L R

Tip

Ring

Sleeve

Tip

Ring

Do not tin the wires!

N * DVI models only. Non DVI models have a 15-pin HD connector

in place of the DVI connector and do not feature EDID emulation.

68-1039-50

Rev. A

08 09

DVS 304 Series • Setup Guide

DVS 304 Series — Setup Guide (cont'd)

Step 3 — Connect outputs

Connect video and audio output devices to the applicable connectors marked “Outputs” (see above). g and h

Video RGB (RGBHV, RGBS, RGsB) or HD component (R-Y, Y, B-Y) video output — For connect cables to the BNC's or VGA/DVI-I as shown

below. Outputs are scaled or pass-through RGB ,or scaled component video and can be scaled to more than 60 different output rates.

N RGB pass-through is available on analog outputs only. DVI output is disabled in RGB pass-through mode.

RGBHV

/R-Y

/B-Y

/R-Y

/B-Y

RGsB

/R-Y

RGBS

/B-Y

Component video (Y, R-Y, B-Y)

/R-Y

Analog video output

For connect a suitable display device DVI-I (digital and analog) output (DVS 304 DVI models only) ,

to this DVI-I connector for scaled RGB or component video (simultaneous digital and analog outputs).

Audio — Wire the captive screw audio connectors as shown above.

Step 4 — Connect control devices

LAN Ethernet port j — Connect to an Ethernet LAN or WAN via this RJ-45 connector to control the switcher from a remote

location using a PC’s Internet browser, or the control program (the Extron Signal Processing Products Control Program).

The Ethernet connection indicator LEDs indicate the status of the Ethernet connection: the green LED lights when connected to an

Ethernet LAN, and the amber LED ickers as the devices communicate.

N Do not use standard telephone cables, as they do not support Ethernet or Fast Ethernet. Do not stretch or bend cables as transmission

errors could occur.

Remote port —k For serial RS-232 control, connect a host computer or control system via this 9-pin D connector.

RS-232 protocol (default values): 9600 baud, 1 stop bit, no parity, 8 data bits, no ow control.

N See chapter 4, “SIS™ Programming and Control”, in the , for deﬁnitions of the SIS commands. DVS 304 Series User’s Manual

See chapter 5, “DVS 304 Series Control Software” to install and use the control software.

Use an RS-232 cable that only utilizes Tx (2), Rx (3), and ground (5) to avoid activating the contact closure feature (refer to the

DVS 304 Series User's Manual , chapter 2).

Step 5 — Connect power

AC power connector a — Plug in a standard IEC power cord from a 100 to 240 VAC, 50 - 60 Hz power source into this receptacle

Powering Up

When applying power to the DVS, the unit undergoes a start-up self testing sequence (see image below), and then the LCD displays

the default display cycle, showing the active input, input signal type, and the output resolution and refresh rate.

sec.

App ly

Power

Extron

El ec t roni cs

sec.

2 sec.

sec.

Default Display Cycle

INPU T 4

RGB SC ALED 1024x768@60.0Hz

OU T PUT

Th e i np ut an d o utp ut r ates sho wn

in the def ul t di spl ay cycle ma y d ifa fer,

de pe nd ing on the ac t i i np ut a nd type o f vide o s ign alve

All input LEDs flash

once in sequence

(last activ then 1-4).e,

sec.

Last active input

LED remains lit

(here input 3).

= flashing

Key

60-xxxx-xx

FW ve 2.00r.

= lit

DVS 304

DVI AD

sec.

N When in use and not in any menu, the LCD screen defaults to cycling through the current input/output conﬁguration. The displayed

content may vary, depending on the input video signal type (see typical default display above).

DVI-I

Unbalanced Stereo Output

L R

Balanced Stereo Output

Left

Right

CAUTION

For unbalanced audio, connect the sleeve(s) to the center contact

ground. DO NOT connect the sleeve(s) to the negative (-) contacts.

Tip

Slee sve

Tip

NO GROUND HERE

L R

Left

Right

Tip

Ring

Slee sve

Tip

Ring

A o outputudi

DVS 304 Series • Setup Guide

Front Panel Overview

DVS 304

VIDEO AND RGB SCALER

ADJUST

2 3 4 MENU NEXT

3456 7

a Input selection buttons — Select/switch inputs and indicate which input is active (button LED lights green). A blinking LED

indicates an audio breakaway input (audio models only).

Button 1 selects input 1 - composite video.

Button 2 selects input 2 - composite video, S-video, or component video.

Button 3 selects input 3 - S-video.

Button 4 selects input 4 - RGB scaled (RGBHV, RGBS, RGsB), RGB pass-through, RGBcvS, YUVi, YUVp/HDTV, S-video or

composite video.

N RGB pass-through mode (inputs pass at their native rate without additional processing) is available on analog outputs only. The DVI

output is disabled in RGB pass-through mode.

b Menu button — This button allows navigation through the DVS's system menu (top level).

c Next button — This button allows navigation through the submenus and to start selected functions, such as Auto-Image™ .

d LCD display — This 12x2 screen displays device status, settings, and menu conguration information.

e Infrared (IR) sensor — This sensor is used to receive IR signals from the IR 902 remote control.

N For detailed information on the IR 902 remote, refer to the , available online at DVS 304 Series User's Manual www.extron.com.

f g and Adjust knobs — These are used with the menu navigation buttons to adjust device settings and picture control.

Setting the front panel lock (Executive mode)

The DVS has a front panel security lock feature that limits the operation of the unit from the front panel.

Executive mode 0 (disabled) — The front panel is fully unlocked. This is the default setting.

Executive mode 1 (enabled) — The front panel is locked except for input switching.

Enabling or disabling Executive mode 1 from the front panel

Press and hold the Menu and Next buttons until the LCD display indicates the Executive mode is either enabled or disabled.

N If the DVS is in Executive mode 0 (unlocked), this procedure selects mode 1 (locked).

If it is in Executive mode 1, this procedure selects mode 0 (unlocked).

When Executive mode is enabled and a front panel action is attempted (other than input switching), the LCD displays the status for

2 seconds. Executive mode 1 can also be enabled or disabled by SIS commands.

Conﬁguring the DVS using the front panel system menus

The DVS has eight or nine front panel conguration menus:

Start Auto Image, Input Conguration, Picture Control, Output Conguration, Audio Conguration (only seen on audio models),

Memory Presets, IP Conguration, Advanced Conguration, and the Exit Menu.

N For detailed information on the menus, refer to the , available online at DVS 304 Series User's Manual www.extron.com.

To use a menu, press the Menu button to access the Main menu, then repeatedly press the Menu button to cycle through the list to

the desired menu. Press Next to enter the desired submenu, and follow the steps on page 4.

N Press Menu at any time to exit a submenu and return to the main menu.

Menu Menu

START AUTO

IMAGE ON INx

INPUT

CONFIG

PICTURE

CONTROL

OUTPUT

CONFIG

AUDIO

CONFIG

MEMORY

PRESETS

CONFIG

AD NCED VA

CONFIG

TO EXIT MENU

PRESS NEXT

(Audio models only)

2 sec.

sec.

Default Display Cycle

INPUT 4

RGB SSPA 1024 x768@6 0.0Hz

OUT PUT

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	DVS 304 DVI D
Soort bediening:	Knoppen
Kleur van het product:	Zwart
Gewicht:	1500 g
Breedte:	222 mm
Diepte:	267 mm
Hoogte:	44 mm
Gewicht verpakking:	2150 g
Breedte verpakking:	356 mm
Diepte verpakking:	330 mm
Hoogte verpakking:	102 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
AC-adapterfrequentie:	50 - 60 Hz
AC-adapter ingangsspanning:	100 - 240 V
Ondersteunde video-modi:	480p, 576p, 720p, 1080i, 1080p
Certificering:	CE, c-UL, UL, C-tick, FCC Class A, ICES, VCCI Class A
Formaat analoog signaal:	NTSC 3.58, NTSC 4.43, PAL, SECAM
Ingang stroom:	Ja
Digitale horizontale frequentie:	15 - 100 kHz
Digitale verticale frequentie:	50 - 120 Hz
Temperatuur bij opslag:	-40 - 70 °C
RJ-45 ports hoeveelheid:	1
Rackcapaciteit:	1U
Stroomverbruik (typisch):	30 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Ingangsstroom AC-adapter:	0.3 A
Gain aanpassing:	Digitaal
Geschaalde resoluties:	640 x 480,1920 x 1200
DC offset:	1300 mV
Sync-uitgangsimpedantie:	75 Ohm