Extron DTP3 CrossPoint 622 Handleiding
Extron
Schakelaar
DTP3 CrossPoint 622
Lees hieronder de 📖 handleiding in het Nederlandse voor Extron DTP3 CrossPoint 622 (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
1
DTP3 CrossPoint Series • Setup Guide
IMPORTANT NOTE:
Go to www.extron.com for the complete user guide, installation instructions, and speciîš¿cations before connecting the
product to the power source.
This guide provides basic instructions for an experienced technician to install the DTP3 CrossPoint matrix switchers.
The DTP3 CrossPoint matrix switchers distribute HDCP-compliant HDMI and Extron proprietary DTP video and audio signals to any
combination of outputs simultaneously (see îš¿gure 1). The DTP3 CrossPoint inputs can be conîš¿gured to accept DTP3, DTP, or XTP
signals and the DTP outputs can be conîš¿gured to DTP, DTP3, XTP, or HDBaseT modes via Product Conîš¿guration Software (PCS).
The DTP3 CrossPoint switchers support 4K 60 Hz 4:4:4 signals, audio DSP Pro, and AEC and are compatible with all DTP and DTP3
transmitters and receivers. Additionally, the DTP3 CrossPoint SL models have the ShareLink Pro module for sharing content from
computers, tablets, and smartphones.
This guide provides basic instructions for an experienced technician to set up and operate the DTP3 CrossPoint matrix switchers. For
additional information and speciîš¿cations, see the select DTP3 CrossPoint product page at www.extron.com.
NOTE: The images in the following diagrams use the DTP3 CrossPoint 884 IPCP A unless otherwise noted.
Net A P U 10 E ES02 S RI
OVER
T EMP
1 2
LIMITE R/PROT E CT
SIGN AL
DTP3 SS POINT CRO SERIES
SCAL ING PRESENTATI ON MATR IX SWITCH ER
INPU T S
12345678
9 10 11 12
CO NT RO L I/OLOG O
OU T UTP S
12345678
9 10 11 12
AUD IOVIDEOSELEC T ESC AP EVIEWPR ES ETENT ER
CONFIG
COM
PoE+
PWR
RTS
CTS
2
3 1 2 3 3
1 2
4
Tx
Rx
I/O
2
1
IR/S
3
1 2
4
RELAYS
OU T P U T S
DT P R EMOT E P OWER AMP OUT
DT P3 I/OINP UT S
DTP3
5 6 1 2 3 4 5 6 7 8 9 10
DTP
11
12 8Ω/4Ω
8Ω 70V
OUT PUT MODE
S TEREO
LIMITER/
PROT ECT BRIDGED MONO
100V
Extron
FF 220T
Flat Field Ceiling Speakers
Extron
NetPA U 1002
Power Amplier
Extron
SM 26
Surface Mount
Speakers
Room A
Ceiling
Conference Table
Room B
Extron
DTP3 CrossPoint 884 IPCP A
Scaling Presentation Matrix
Ceiling Mic Array
(8 Mic Channels)
Microphones
Microphones
Ethernet
Ethernet
Ethernet
Audio
Audio
Figure 1. Typical Application of the DTP3 CrossPoint 884 IPCP A
The switchers are available in four matrix sizes (the number of inputs, outputs, and conîš¿gurable DTP3 I/Os) and three equipment
congurations (di󰀨erentiated by their audio, control, and ShareLink Pro [662/642/622 models only] capabilities) for a total of 11 models:
Matrix sizes —
• • DTP3 CrossPoint 884 — 8x8x4 DTP3 matrix switcher DTP3 CrossPoint 642 — 6x4x2 DTP3 matrix switcher
• • DTP3 Crosspoint 662 — 6x6x2 DTP3 matrix switcher DTP3 CrossPoint 622 — 6x2x2 DTP3 matrix switcher
Equipment configurations —
• DTP3 CrossPoint base models — Includes unampled audio outputs, with no IPCP Pro 360MQ xi control processor, or ShareLink Pro.
• DTP3 CrossPoint IPCP A models — Includes a built-in Extron IPCP Pro control processor and a Class D power convertible amplier.
• DTP3 CrossPoint IPCP A SL models (662/642/622 models only) — Includes a built-in Extron IPCP Pro control processor, a Class D
power convertible ampliîš¿er, and a ShareLink Pro module.
Control and Configuration — The DTP3 CrossPoints can be controlled and congured via Product Conguration Software (PCS),
DSP Pro Conîš¿gurator (advanced audio), Simple Instruction Set (SIS) commands, and the Internal Web Page.
2
Disconnect Power and Mount the DTP3 CrossPoint
Disconnect power from the switcher and turn o󰀨 all devices that will be connected to it. Select a suitable mounting location, and choose
an appropriate mounting option. Mounting information can be found in the DTP3 CrossPoint Series User Guide on www.extron.com. The
DTP3 CrossPoint matrix switchers can be rack mounted or sit on a table with the provided rubber feet. Make all external connections before
applying power.
Rear Panel Connections
NOTE: Features for all models are shown in îš¿gure 2. Actual models have either a LAN port (
P) or a control processor (N).
RESETRS-232
Tx Rx G
REMOT E
50 60 Hz
100-240V ~5.0A MAX
DTP3 CrossPoint 884
1 (PRI/PoE) 2 (S EC) USB-C
IN/OUT
DMP EXPA T USB AUDIO
1 - 2
CLASS 2 WIRING
AMP O TPUT
1
2
3
4
5 6 5
6
7
8
IN P UT S ( E X T EN DED PO S S UP PO DT P 3/ XT P )RT RT
9OUTIN 10 OUTIN 11 OUTIN 12 OUTIN
D T P 3 I / O
R
T x Rx G
RT S CT S
T x Rx G T x Rx G
1 2 C 3 4 C
CONTROL
AV LAN 2/PoE + AV LAN 3/PoE+
LAN AV LAN 1
1 2
1 2 3 4 GS G S G
IR / SERIAL RELAYS DIGIT AL / IO
COM 1 COM 2 COM 3
LI E IN
1 2
3
4
1
2
+48V
MIC/LINE IN
1 2
3 4
LINE OUT
1 2
IN
SIG LINK
IN
SIG LINK
IN/OUT
SIG LINK
IN/OUT
SIG LINK
IN/OUT
SIG LINK
IN/OUT
SIG LINK
+
BR -
Select ab le T P OR HDMI
O U T P U T S ( E XT E ND E D P O S S UP P ORT RT D T P 3/X T P / H D B T )
7
8
5B
6B
6A5A3B
4B
4A3A1B
2B
2A1A
OUT
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
OUT
SIG LINK
DT P2 CROS SPO
LAN
REMOT E
Tx Rx G
R SET
O
O
O
O
O
O P
P
P
P
P
P
N
N
N
N
N
N O
O
O
O
O
O Q
Q
Q
Q
Q
QF
F
F
F
F
F G
G
G
G
G
G H
H
H
H
H
H M
M
M
M
M
MJ
J
J
J
J
JK
K
K
K
K
K L
L
L
L
L
LI
I
I
I
I
I
E
E
E
E
E
E
D
D
D
D
D
DC
C
C
C
C
CD
D
D
D
D
DR
R
R
R
R
R D
D
D
D
D
DA
A
A
A
A
A A
A
A
A
A
A D
D
D
D
D
DB
B
B
B
B
B
Figure 2. DTP3 CrossPoint 884 IPCP A Rear Panel Connections
Video Inputs and Outputs
A HDMI inputs — Connect HDMI digital video (or DVI with appropriate adapters) into these HDMI ports (see the included LockIt HDMI
Cable Lacing Bracket Guide).
B TP inputs — Connect compatible Extron DTP or XTP signals into these RJ-45 ports using TP cables.
C DTP3 I/O ports and LEDs — Connect compatible Extron DTP3 input or output signals into these RJ-45 ports using XTP DTP cables.
Configure these ports via PCS (see the ). The LEDs above the port indicate whether the port is DTP3 CrossPoint Series PCS Help File
configured as an input or an output (IN or ).OUT
ATTENTION:
• Remote power is not disabled when changing the I/O port from input to output or output to input. Disable remote power before
changing the I/O port and reconfigure after the change.
• L’alimentation à distance n’est pas désactivée lors du changement de port d’E/S de l’entrée vers la sortie ou de la sortie
vers l’entrée. Désactivez l’alimentation à distance avant de changer de port d’E/S et effectuez une reconfiguration après ce
changement.
D HDMI outputs — Connect HDMI video displays (or DVI with appropriate adapters) into these ports (see the included LockIt HDMI Cable
Lacing Bracket Guide).
NOTE: The signal output on the TP (A) output is duplicated on HDMI (B) outputs.
E TP outputs — Connect compatible Extron DTP receivers, XTP matrix switchers, or HDBaseT-enabled devices into these RJ-45 ports
using TP cables.
Audio Inputs and Outputs
F Dante AT ports — Connect to other Dante-enabled devices to form a larger matrix.
G DMP EXP port and LED —
• Port — Connect an EXP-enabled device to this RJ-45 port for a digital audio connection using Extron proprietary protocol. A
shielded 1-foot cable is included with the DMP 128. No setup is required. Just connect the two devices (see the selected DMP User
Guide for more details).
• Link LED — Lights to indicate that the port is connected to a compatible device.
H USB Audio — Connect a USB-C cable to deliver a minimum of 4x4 channel audio interface to a host PC, using either Mac or PC
drivers.
I +48 V (phantom power) LEDs — Light to indicate +48 V phantom power is switched on via software.
J Mic/Line inputs 1 through 4 — Connect mono balanced or unbalanced microphone or line level sources to these four 3-pole, 3.5 mm
captive screw ports (see on page 3
figure 3 for wiring).
K Line In inputs 1 and 2 — Connect up to two balanced or unbalanced analog audio sources to these 6-pole 3.5 mm captive screw ports
(see figure 3 to wire the connectors)..
3
DTP3 CrossPoint Series • Setup Guide
6-pole Audio INPUT Wiring
Balanced Input Unbalanced Input
Sleeve
Ring
Tip
Tip
Sleeve
Jumper
Tip
Sleeve
Jumper
Sleeve
Ring
Tip
3-pole Audio INPUT Wiring
Balanced Input
" (5 mm) MAX. (typ)
3
16
Sleev
e
Ring
Tip Tip
Sleeve
Jumper
Unbalanced Input
Figure 3. Balanced and Unbalanced Audio Input Wiring Diagram
L Line Out outputs 1 and 2 (see figure 2 on page 2) — Connect audio devices such as an audio L R amplifier or powered speakers
to the two 3.5 mm, 3-pole captive screw ports (see figure 4 to wire the connectors).
Balanced Input Unbalanced Input
Sleeve
Ring
Tip
Sleeve
Ring
Tip Tip
Sleeve
NO Ground Here
Tip
Sleeve
NO Ground Here
Figure 4. Audio Output Wiring
ATTENTION:
• For unbalanced audio OUTPUT, connect the sleeves to the ground
contact. DO NOT connect the sleeves to the negative (-) contacts.
• Pour la sortie audio asymétrique, connectez les manchons au contact au
sol. Ne PAS connecter les manchons aux contacts négatifs (–).
M Amp Output (IPCP A models only) — Connect passive speakers to this 5 mm, 4-pole captive screw port to receive an audio line input,
or a line input from the audio expansion bus. The selectable output modes of the amplifier are:
• • 2 x 100 watts @ 8Ω / 4Ω 1 x 200 watts @ 70 volts (Bridged)
• • 1 x 200 watts @ 8Ω (Bridged) 1 x 200 watts @ 100 volts (Bridged)
Control and Power
N IPCP Pro 360MQ xi control processor (IPCP A models only) — The Extron IPCP Pro 360MQ xi control processor card integrates
Ethernet connectivity into AV systems to allow users to remotely control, monitor, and troubleshoot AV equipment, including display
devices and switchers. The IPCP Pro 360MQ xi control card offers:
• IPCP Reset button and LED —
• Reset button — Initiates levels of control processor reset. For di󰀨erent reset levels, press and hold the recessed Reset
button while the switcher is running or while powering up.
• Reset LED — Indicates the level reset initiated on the control processor.
• COM1, COM2, and COM3 ports — Connect to the 5-pole COM port for both hardware and software ow control. Connect to the
3-pole COM ports for software ow control only.
• Digital I/O port — Congure each port as a digital input or output, with or without +5 VDC pull-up. Monitor or trigger events and
functions (toggle relays, issue commands, send e-mail), once conîš¿gured.
• IR/Serial ports — Connect to the control processor to use infrared signals or unidirectional RS-232 serial signals to control various
devices via these ports. Set output signal type (IR or serial) during conîš¿guration.
• Relays ports — Connect devices for contact control.
• AV LAN Ethernet ports — Connect directly to the DTP3 CrossPoint.
• LAN Ethernet port — Connect the IPCP to an Ethernet network (for conguration and control of the IPCP and the devices
connected to it). Plug a cable into this RJ-45 socket and connect the other end of the cable to a network switch, hub, router, or PC
connected to a local network or the Internet
See the enclosed IPCP Pro Q xi and xi Series Setup Guide IPCP Pro Q xi and xi User Guide or the at www.extron.com to make all
connections and to conîš¿gure and operate the IPCP Pro 360MQ xi control processor.
NOTES:
• The additional AV LAN ports function as multiport, unmanaged network switches for additional devices to connect to the same
network.
• If the DTP3 CrossPoint is connected via the front panel USB-C, the hardcoded IP address is 203.0.113.22.
• If connected to the rear panel AV LAN ports, the DTP3 CrossPoint default IP address is 192.168.254.254.
• If connected to the rear panel IPCP LAN port, the default IP address is 192.168.253.250.
• If the DTP3 CrossPoint IP address is changed, the AV LAN IP address (192.168.254.250) MUST be changed in Toolbelt to
the same subnet as the DTP3 CrossPoint in order to connect through the AV LAN port.
O Remote RS-232 port — Connect a serial RS-232 device into the matrix switcher via this 3.5 mm,
3-pole captive screw port for remote control of the switcher (see image on the right to wire the
connector).
P LAN (Ethernet) port (non-IPCP model) — (Optional) Connect a network WAN or LAN hub, a control
system, or a computer to the Ethernet RJ-45 port.
NOTE: The factory default IP address is 192.168.254.254.
TxGnd
RS-232 Device
Rx
Tx Rx
RS- 232
G
REMOTE
Q — CrossPoint switcher Reset button and LED
NOTE: The factory conîš¿gured passwords for all accounts on this device have been set to the device serial number. In the event of
a complete system reset, the passwords convert to the default, which is extron for the and .Admin User
Product specificaties
| Merk: | Extron |
| Categorie: | Schakelaar |
| Model: | DTP3 CrossPoint 622 |
Heb je hulp nodig?
Als je hulp nodig hebt met Extron DTP3 CrossPoint 622 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schakelaar Extron
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
6 September 2024
5 September 2024
15 Augustus 2024
14 Augustus 2024
Handleiding Schakelaar
- Schakelaar Bosch
- Schakelaar Philips
- Schakelaar HP
- Schakelaar IKEA
- Schakelaar Panasonic
- Schakelaar Huawei
- Schakelaar Asus
- Schakelaar Honeywell
- Schakelaar Yamaha
- Schakelaar Abus
- Schakelaar Alcatel
- Schakelaar Alecto
- Schakelaar Alpine
- Schakelaar Ansmann
- Schakelaar Apc
- Schakelaar Audiovox
- Schakelaar B-tech
- Schakelaar Basetech
- Schakelaar Behringer
- Schakelaar Belkin
- Schakelaar Berker
- Schakelaar Boss
- Schakelaar Brennenstuhl
- Schakelaar Buffalo
- Schakelaar D-Link
- Schakelaar Digitus
- Schakelaar Eaton
- Schakelaar EBERLE
- Schakelaar Ebode
- Schakelaar Edimax
- Schakelaar Elektrobock
- Schakelaar Elro
- Schakelaar Emerson
- Schakelaar Eminent
- Schakelaar Engenius
- Schakelaar Extech
- Schakelaar Finder
- Schakelaar Flamingo
- Schakelaar GAO
- Schakelaar Generac
- Schakelaar Gira
- Schakelaar Goobay
- Schakelaar Grandstream
- Schakelaar Grasslin
- Schakelaar Hager
- Schakelaar Hama
- Schakelaar Hikvision
- Schakelaar Intermatic
- Schakelaar Inverto
- Schakelaar Kathrein
- Schakelaar KlikaanKlikuit
- Schakelaar Konig
- Schakelaar Kopp
- Schakelaar Lancom
- Schakelaar LevelOne
- Schakelaar Linksys
- Schakelaar Logilink
- Schakelaar Manhattan
- Schakelaar Marmitek
- Schakelaar Mercury
- Schakelaar Merlin Gerin
- Schakelaar Mikrotik
- Schakelaar Monacor
- Schakelaar Nedis
- Schakelaar Netgear
- Schakelaar Paladin
- Schakelaar PCE
- Schakelaar Perel
- Schakelaar Plantronics
- Schakelaar Powerfix
- Schakelaar Profile
- Schakelaar Provision ISR
- Schakelaar Pyle
- Schakelaar QNAP
- Schakelaar Renkforce
- Schakelaar Rex
- Schakelaar Robbe
- Schakelaar Schneider
- Schakelaar SEC24
- Schakelaar Shimano
- Schakelaar Silvercrest
- Schakelaar Smartwares
- Schakelaar Speaka
- Schakelaar Suevia
- Schakelaar Sygonix
- Schakelaar Sylvania
- Schakelaar Tenda
- Schakelaar Tesla
- Schakelaar Theben
- Schakelaar Tiptel
- Schakelaar Toolcraft
- Schakelaar Tork
- Schakelaar TP Link
- Schakelaar Trendnet
- Schakelaar Triax
- Schakelaar Trotec
- Schakelaar Unify
- Schakelaar UPM
- Schakelaar Velleman
- Schakelaar Vivanco
- Schakelaar WHALE
- Schakelaar Worx
- Schakelaar ZyXEL
- Schakelaar Jabra
- Schakelaar Jung
- Schakelaar Omnitronic
- Schakelaar One For All
- Schakelaar Clas Ohlson
- Schakelaar CSL
- Schakelaar Monoprice
- Schakelaar Steren
- Schakelaar DoorBird
- Schakelaar Ubiquiti Networks
- Schakelaar Kaiser
- Schakelaar Cotech
- Schakelaar Atlona
- Schakelaar Hamlet
- Schakelaar Comet
- Schakelaar Vivolink
- Schakelaar Techly
- Schakelaar SIIG
- Schakelaar Merten
- Schakelaar Tripp Lite
- Schakelaar Chacon
- Schakelaar Nexa
- Schakelaar Dormakaba
- Schakelaar SPC
- Schakelaar Cisco
- Schakelaar Victron Energy
- Schakelaar Delta Dore
- Schakelaar Vemer
- Schakelaar Matrox
- Schakelaar Gefen
- Schakelaar Ei Electronics
- Schakelaar Fibaro
- Schakelaar GEV
- Schakelaar Juniper
- Schakelaar Planet
- Schakelaar Chamberlain
- Schakelaar Intellinet
- Schakelaar CyberPower
- Schakelaar SunBriteTV
- Schakelaar Lindy
- Schakelaar IOGEAR
- Schakelaar Black Box
- Schakelaar IFM
- Schakelaar DataVideo
- Schakelaar Wago
- Schakelaar Totolink
- Schakelaar Dahua Technology
- Schakelaar AV:link
- Schakelaar PreSonus
- Schakelaar Mercusys
- Schakelaar Elation
- Schakelaar EVE
- Schakelaar Audac
- Schakelaar Vacmaster
- Schakelaar ATen
- Schakelaar RGBlink
- Schakelaar PAC
- Schakelaar Wentronic
- Schakelaar Adder
- Schakelaar Homematic IP
- Schakelaar AMX
- Schakelaar OSD Audio
- Schakelaar Equip
- Schakelaar Crestron
- Schakelaar ORNO
- Schakelaar Aeon Labs
- Schakelaar Electro Harmonix
- Schakelaar StarTech.com
- Schakelaar PureLink
- Schakelaar Advantech
- Schakelaar Smart-AVI
- Schakelaar Brilliant
- Schakelaar Kramer
- Schakelaar Micro Connect
- Schakelaar KanexPro
- Schakelaar Intelix
- Schakelaar Blustream
- Schakelaar Avocent
- Schakelaar Shelly
- Schakelaar ICasa
- Schakelaar Vimar
- Schakelaar Kemo
- Schakelaar H-Tronic
- Schakelaar Legrand
- Schakelaar Kraus & Naimer
- Schakelaar Noble
- Schakelaar Intertechno
- Schakelaar Ecler
- Schakelaar Rule
- Schakelaar CYP
- Schakelaar Phoenix Contact
- Schakelaar Seuthe
- Schakelaar Maclean Energy
- Schakelaar SmartAVI
- Schakelaar DEHN
- Schakelaar Cudy
- Schakelaar Heitronic
- Schakelaar Noark
- Schakelaar Cooking Performance Group
- Schakelaar Ernitec
- Schakelaar Adviti
- Schakelaar Flic
- Schakelaar IB Connect
- Schakelaar Liberty
- Schakelaar Cambium Networks
- Schakelaar 2USB
- Schakelaar Roline
- Schakelaar KVM-TEC
- Schakelaar BZBGear
- Schakelaar STI
- Schakelaar Epiphan
- Schakelaar Mach Power
- Schakelaar Axing
- Schakelaar Raritan
- Schakelaar ConnectPro
- Schakelaar Atlantis Land
- Schakelaar Pizzato Elettrica
- Schakelaar Baco
- Schakelaar SEADA
- Schakelaar Doepke
- Schakelaar IPGARD
- Schakelaar Setti+
Nieuwste handleidingen voor Schakelaar
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024
20 November 2024