Extron ACP 106 EU Handleiding

Extron Niet gecategoriseerd ACP 106 EU

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron ACP 106 EU (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

ACP 106 EU/MK • Setup Guide

The Extron ACP 106 EU/MK Audio Control Panels are fully congurable control interfaces for use with any Extron ACP-enabled

device.

Each ACP 106 EU/MK includes two ACP ports, which support power and communication between the host device and the

ACP 106 EU/MK. Up to eight ACP panels can be used per host device for more demanding control needs.

NOTE: The ACP 106 EU front and rear panels are identical to those of the ACP 106 MK. The only difference is the shape of

the plastic faceplate attached to the front of the device. The panels function identically.

Front Panel Features

VOLUME

MUTE

PROGRAM

MIC

Extron

Figure 1. ACP 106 EU Front Panel

Planning the System and Installation

When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see

the ACP 106 EU and ACP 106 MK product pages at www.extron.com for more information about the ACP 106 EU/MK).

Installation

Step 1: Get Ready

Use the following checklist to prepare for the installation:

Download and install the latest version of software, rmware, and device drivers needed to congure the host device and

congure the connected ACP products (see the host device user guide, available on www.extron.com, for details on

software and drivers).

Obtain cables, mounting hardware, and any other supplies required for ACP 106 EU and MK installation.

Figure 2. ACP 106 EU Rear Panel

ACP

PWR LOAD

= 1.5W

+S -S G +V S - G

STATUS

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

Rear Panel Features

A ACP Ports (2)

B Connection Status LED

C Reset Button

D Bus ID DIP Switches

A Mute Buttons

B Transmit LED

C Volume Buttons

D Volume LED Meter

E Function Button 1

F Function Button 2

ACP 106 EU/MK • Setup Guide (Continued)

Step 2: Prepare the Installation Site

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Extron recommends installing the ACP 106 EU/MK into a grounded, UL Listed electrical junction box.

• Extron recommande d’installer le ACP 106 EU/MK dans un boîtier d’encastrement électrique mis à la terre, listé UL.

• If the ACP 106 EU/MK will be installed into ne furniture, it is best to hire a licensed, bonded craftsperson to cut the

access hole and perform the physical installation so the surface will not be damaged.

• S’il est prévu d’installer le ACP 106 EU/MK dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et

qualié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.

• Follow all national and local building and electrical codes that apply to the installation site.

• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.

NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 106 EU/MK

must be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with

the ACP106 D.

Americans with Disabilities ACT (ADA) Compliance

When planning where to install these devices, consider factors affecting accessibility of the button panel such as height

from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see sections

307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the available at 2010 ADA Standards for Accessible Design

http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.

Site Preparation

Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external wall boxes (EWBs), and surface or

tabletop mounting boxes for use with the ACP button panels. The ACP 106 EU and ACP 106 MK are 1-gang EU and MK size

devices.

Step 3: Removing the Plastic Faceplate, Button Panel, and Changing

the Buttons

The plastic faceplate and buttons can be replaced. Additional buttons ship with the device and

others can be ordered from www.extron.com.

To change the buttons:

1. Insert the Extron removal tool (pry tool) between one side of the plastic faceplate and the

button plate. Release the catch holding the wallplate to the metal mounting plate (see 1

in the gure to the right). If necessary, use the pry tool to release the second catch on the

opposite side.

2. To separate the button plate from the control plate, insert a small at-bladed screw driver

into one of the slots (see 2 in the gure at the bottom of the page).

3. Press the blade of the screw driver in until there is an audible

click and the tab is pushed out of the slot.

4. Repeat steps 2 and 3 to release all four tabs holding the button

plate in place.

5. Tilt the top of the button plate forward as it is removed to

prevent the buttons from falling out (3).

VOLUME

MUTE

MIC

PROGRAM

VOLUME

MUTE

MIC

PROGRAM

Extr onExtr on

Insert

to lin

6. To remove a button, press a button backward through its slot in the button plate until the

membrane containing the button is free.

7. To replace a button, align the two pegs in the button membrane with the holes located at

opposite corners of the empty slot on the back of the button faceplate and push the button

forward so it ts in the desired slot (see the gure to the right). Ensure the button text

orientation is correct.

8. Press the button into the button plate until the pegs on the membrane are seated in the

corresponding holes.

9. Repeat steps 6 through 8 for any other buttons being replaced.

10. Align the back of the button plate with the control plate and press it into place. The four

tabs released in steps 2 through 4 snap back into place.

11. Ensure the plastic faceplate and metal mounting plate are in the correct orientation. To reattach the plastic faceplate, press

the faceplate back into the metal mounting plate, using the two catches released in step 1.

Step 4: Set Bus ID Addresses

ACP

+S -S G+V +V +S -S G

PWR LOAD

= 1.5W

ST USAT

GREEN

AMBER

RED

LINK

COM ERROR

ID ERROR

V+

S G–

0 1 0 0 1 0

1 2 3 4 5 6

0 0 0 0 0 1

1 2 3 4 5 6

18Unit address

DIP switches

Binary address

ACP port on a

DMP Plus, or on

another ACP

endpoint

ACP Ports

• Connect up to eight (8) ACP endpoint devices per

DMP Plus.

• Wi the connectors the same at both ends.re

• These ports a identical. You can connect devices re

interchangeably to either port.

• Do not exceed a total of 1000 feet (305meters) of cable for

connections between the DMP Plus and all of the ACP

panels.

• Power is provided by the DMP Plus, a PS 1220EB power

inserter, or an Extron 12 VDC power supply.

Bus ID Address DIP Switches

• Use these DIP switches to set the six-bit, binary

bus address for the ACP 106 EU/MK.

• Each ACP connected to the same DMP Plus

must have a address.unique

• Switch 1 (on the left) is the highest value (32, the

the most signicant bit [labeled “MSB”]).

• Switch 6 (on the right) is the lowest (1, the least

signicant bit [labeled “LSB”]).

• = on = 1, = off = 0Up Down

Examples:

Figure 3. ACP 106 EU/MK Rear Panel and Bus ID DIP Switch Assembly

Set the bus identication (bus ID) DIP switches for the ACP 106 EU/MK and

any other ACP panels being connected to the system. Each ACP device

must have a unique bus ID. If multiple panels have the same bus ID, address

conicts may cause one or more of the panels to not be recognized in DSP

Congurator or by the host device. Up to eight ACP devices can be connected

in the same system.

Each ACP device in a system must have a unique six-digit binary bus ID. ACP

bus IDs are set using the DIP switch assembly on the rear panel of the ACP

106 EU/MK (see gure 3).

Switch 1 on the left sets the most signicant bit (highest number, 32) while

switch 6 on the right sets the least signicant bit (the lowest number, 1). See

the example addresses to the right.

Slide

1 2 3 4 5 6

BUS ID

Example Addresses

Bus ID

(Decimal)

Binary

Address

DIP Switch

Setting

0 000000*

1 2 3 4 5 6

1 000001

1 2 3 4 5 6

2 000010

1 2 3 4 5 6

3 000011

1 2 3 4 5 6

4 000100

1 2 3 4 5 6

5 000101

1 2 3 4 5 6

6 000110

1 2 3 4 5 6

7 000111

1 2 3 4 5 6

8 001000

1 2 3 4 5 6

*Address 000000 is reserved for the control processor and cannot be used by any ACP devices.

Product specificaties

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	ACP 106 EU
Kleur van het product:	Black, White
Gewicht:	100 g
Breedte:	81 mm
Diepte:	10 mm
Hoogte:	81 mm
Materiaal:	Metal, Plastic
Aantal polen:	4P