Extron 12G HD-SDI 101 Handleiding

Extron Niet gecategoriseerd 12G HD-SDI 101

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron 12G HD-SDI 101 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

12G HD-SDI 101 • Setup Guide

Introduction

This guide provides instructions for an experienced installer

to set up and operate the Extron 12G HD-SDI 101, a cable

equalizer for SDI, HD-SDI, 3G-SDI, 6G-SDI, and 12G-SDI digital

video.

The Extron 12G HD-SDI 101 is a 1 input, 1 output HD-SDI signal

equalizer that can recondition and equalize digital video signals

up to 12G-SDI due to losses incurred from long cable runs. The

equalizer is typically placed at the end of a long cable run.

Installation

Mounting the Unit

Mounting instructions can be found in on page 3. Compatible optional hardware is listed on the Extron Mounting the Equalizer

website (www.extron.com).

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

Connections and Indicator

12G HD-SDI 101

POWER

12V

0.1A MAX

INPUT

OUTPUT

AA BB CC DD

Front

Panel

Rear

Panel

Figure 1. 12G HD-SDI 101 Rear and Front Panels

Rear Panel

A — Connect the provided external 12 VDC, 6 watt power supply to this 2-pole, orange, 3.5 mm captive Power connector

screw connector. See on the next page.

Power Connector Wiring

B — This female BNC connector accepts an HD-SDI input.HD-SDI input

The maximum length from the signal source to the 12G HD-SDI 101 input varies, dependent on the input:

Format Max. length Format Max. length

12G SDI 230 feet (70 m) HD-SDI 787 feet (240 m)

6G SDI 295 feet (90 m) SDI 984 feet (300 m)

3G SDI 590 feet (180 m)

NOTE: The maximum signal transmission distance depends on signal resolution, the source, the display, and the quality

of the cable.

C — This female BNC connector provides an equalized and reclocked HD-SDI output.HD-SDI output

Front Panel

D — The LED lights green when the unit is receiving power.Power LED

POWER

12V

0.1 A MAX

INPUT

OUTPUT

400’ RG6 Cable

12G ayHD-SDI Displ

Extron

12G 1HD-SDI 10

Cable Equalizer

12G HD-SDI Camera

12G HD-SDI 101 • Setup Guide (Continued)

Power Connector Wiring

Figure 2 shows how to wire the connector. Use the supplied tie-wrap to strap the power cord to the extended tail of the

connector.

Power Supply

Output Cord

Captive Screw

Connector

SECTION A–A

Ridges

Smooth

A A

Tie

Wrap

Figure 2. Power Connector Wiring

CAUTION:

ATTENTION :

• The wires must be kept separate while the power supply is plugged in. Remove power before wiring.

• Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand l’alimentation est branchée.

• The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).

• Any longer and the exposed wires may touch, causing a short circuit between them.

• Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est importante. La longueur idéale est de 5mm (3/16inches).

• S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et provoquer un court circuit.

• S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.

• Do not tin the power supply leads before installing them in the connector. Tinned wires are not as secure in the

connector and could be pulled out.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles étamés ne sont pas aussi bien xés

dans le connecteur et pourraient être retirés.

ATTENTION:

• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked “Class

2” or “LPS”, rated output 12 VDC min. 0.1A. Always use a power supply supplied by or specied by Extron. Use of an

unauthorized power supply voids all regulatory compliance certication and may cause damage to the supply and the

end product.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une source d’alimentation certiée

UL de classe 2 ou LPS, avec une tension nominale 12 Vcc, 0.1 A minimum. Utilisez toujours une source d’alimentation

fournie ou recommandée par Extron. L’utilisation d’une source d’alimentation non autorisée annule toute conformité

réglementaire et peut endommager la source d’alimentation ainsi que le produit nal.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération

ou dans les cavités murales.

• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70,

article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently xed to a

building structure or similar structure.

• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code

ANSI/NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas

être xée de façon permanente à une structure de bâtiment ou à une structure similaire.

ATTENTION:

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the unit. The ridges

on the side of the cord (see ﬁgure 2 on the previous page) identify the power cord negative lead.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte pourrait endommager la source

d’alimentation et l’unité. Les stries sur le côté du cordon (voir sur la page 2) permettent de repérer le pôle l’illustration 2

négatif du cordon d’alimentation.

To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter.

Mounting the Equalizer

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

The 1-inch high, eighth-rack width 12G HD-SDI 101 cable equalizer can be placed on a table, mounted in a rack, or mounted

under a desk or table.

Tabletop Use

Afx the included rubber feet to the bottom of the unit and place it in any convenient location.

Mounting Kits

Mount the unit using any optional compatible mounting kit listed on the 12G HD-SDI 101 product page at www.extron.com, in

accordance with the directions included with the kit. For rack mounting, see “UL rack-mounting guidelines” below.

UL rack-mounting guidelines

The following Underwriters Laboratories (UL) requirements pertain to the installation of the unit into a rack.

• Elevated operating ambient temperature — If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore, consider installing the equipment in an

environment compatible with the maximum ambient temperature (TMA = +122 °F, +50 °C) specied by Extron.

• Reduced air flow — Installation of the equipment in a rack should be such that the amount of air ow required for safe

operation of the equipment is not compromised.

• Mechanical loading — Mounting of the equipment in the rack should be such that a hazardous condition is not achieved

due to uneven mechanical loading.

• Circuit overloading — Consideration should be given to the connection of the equipment to the supply circuit and the

effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

• Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment should be maintained. Particular attention

should be given to supply connections other than direct connections to the branch circuit (such as use of power strips).

Troubleshooting

If no image appears:

• Ensure that all devices are plugged in and powered on. The equalizer is receiving power if its power LED is lit.

• Ensure an active input is applied to the equalizer.

• Ensure that the proper signal format is supplied.

• Check the cabling and make corrections as necessary.

• Call the Extron S3 Sales & Technical Support Hotline if necessary. See the Extron for the Extron ofce nearest you.website

Product specificaties

Merk:	Extron
Categorie:	Niet gecategoriseerd
Model:	12G HD-SDI 101

Heb je hulp nodig?

Als je hulp nodig hebt met Extron 12G HD-SDI 101 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Extron

Extron SW USB Pro Handleiding

12 December 2024

Extron AAP 100 Handleiding

10 December 2024

Extron DTP2 T 212 Handleiding

10 December 2024

Extron VoiceLift Pro VLC 302 Handleiding

10 December 2024

Extron AAP 102 Handleiding

10 December 2024

Extron AAP 106 Handleiding

10 December 2024

Extron DMP 128 Plus Handleiding

10 December 2024

Extron DMP 128 FlexPlus Handleiding

10 December 2024

Extron CPM101 Handleiding

10 December 2024

Extron VoiceLift Pro VLH 302 Handleiding

10 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Marklin 56169 Handleiding

27 Januari 2025

Marklin 74613 Handleiding

27 Januari 2025

Marklin 72900 Handleiding

27 Januari 2025

Marklin 72883 Handleiding

27 Januari 2025

Marklin 72897 Handleiding

27 Januari 2025

Marklin 72703 Handleiding

27 Januari 2025

Marklin 72702 Handleiding

27 Januari 2025

Marklin 72884 Handleiding

27 Januari 2025

Marklin 72452 Handleiding

27 Januari 2025

Marklin 72219 Handleiding

27 Januari 2025