Eurospec Easi-Exit DCS2026 Handleiding

Eurospec Niet gecategoriseerd Easi-Exit DCS2026

Lees hieronder de 📖 handleiding in het Nederlandse voor Eurospec Easi-Exit DCS2026 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 297 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Page 1 Door Closer – Model DCS2026 Rev.1
Copyright © 2008 Eurospec Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Installation Instructions
Overhead Door Closer – Model DCS2026
IMPORTANT INFORMATION
Selecting the correct door closer to suit door size
This product is non handed and can be fitted on both left handed and right handed doors.
*Minimum size for use on fire doors
Important notes:
Minimum size 3 MUST be used on fire doors
Hold open arms must NOT be used on fire doors
Maintenance
PLEASE LEAVE THESE INSTRUCTIONS WITH THE END USER
Tel: +44 (0) 1254 274100
Fax: +44 (0) 1254 274111
Web: www.eurospec.co.uk
Check that the door closer closes the door correctly and adjust as necessary. Ensure fixing screws are tight and periodically
apply light oil or grease to arm knuckle joint
Power Size Max. Width of Door Max. Mass of Door
2 850mm 40Kg
3*950mm 60Kg
4 1100mm 80Kg
5 1250mm 100Kg
6 1400mm 120Kg
Eurospec
Architectural Hardware Ltd
Stancliffe Street, Mill HIll
Blackburn, BB2 2QR
Page 2 Door Closer – Model DCS2026 Rev.1
Copyright © 2008 Eurospec Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Installation – Fig 1 Application – Angle of opening 180°
Illustrations show anti-clockwise closing door
1. Ensure that the door & surrounding frame are in good
condition & the door closes freely.
2. Select the correct hand of Fig. 1 easi-fit template
and with the door in the closed position, stick template to
top corner of door and frame. (See Figs. 1 & 2)
3. Determine the power size required and using the supplied
allen key, adjust door closer strength as per chart on
template. Drill pilot holes in door and frame according to
template. Remove slide plate and fix door closer body with
screws supplied, ensuring correct fitting holes are used.
Power adjusting valve must face away from hinge side of
door. (See Figs. 2 & 3)
4. Carefully detach link arm from adjuster arm & securely fix
adjuster arm shoe to frame ensuring the shoe is rotated in
the correct position to suit power size required. (See Fig. 4)
Note: Rotate shoe 180°for power size 4
5. Place link arm onto closer spindle at right angles
to door, fit securing screw, move link arm and re-
connect to adjuster arm. (See Figs. 4 & 5)
Note: To adjust arm to suit depth of frame, loosen
nut, adjust arm & re-tighten nut.
6. Fit spindle cover cap to underside of closer. (See Fig. 5)
7. Check for correct closing & latching speeds and
adjust if necessary. Adjust backcheck as required. (See
Fig.6)
8. Stick easi-exit logo onto indent of slide plate and refit to
door closer. (See Fig. 6)
Fig 1 – Standard Application (Door closer fitted on pull face of door)
Fig. 2
Fig. 3
Fig. 4
Fig. 6 Fig. 5
Adjust power strength of door closer here
USE THESE FITTING HOLES
FOR POWER SIZES 3, 4, 5 & 6
USE THESE FITTING HOLES
FOR POWER SIZE 2
Fig. 1
Stan
dard Application
Adjust if
required
No.1 Closing Speed
No.2 Latching Speed Delayed Action
SIZES 2, 3, 5 & 6
SIZE 4
Note: For delayed action model DCS2026BCDA, adjust valve as required
Page 3 Door Closer – Model DCS2026 Rev.1
Copyright © 2008 Eurospec Failure to install this product as per these instructions &
dimensions shown on template will negate guarantee
Installation – Fig 61 Application – Angle of opening 180°
Fig 61 – Transom Mounting Application (Door closer fitted on frame on push side of door)
Fig. 4
Fig. 6 Fig. 5
Fig. 1
Fig. 2
Fig. 3
Transom Mounting Application
Adjust power strength of door closer here
USE THESE FITTING HOLES
FOR POWER SIZE 3
, 4, 5
& 6 USE T
HESE
FIT
TING HOLES
FOR POWE
R SIZE 2
S
IZES 2, 3, 5 & 6SIZE 4
Adjust if
required
90
No.1 Closing Speed
No.2 Latching Speed Delayed Action
Illustrations show clockwise closing door
1. Ensure that the door & surrounding frame are in good
condition & the door closes freely.
2. Use Fig. 1 easi-fit template and select correct hand of door,
stick template to top corner of door and frame, ensuring
closer is mounted on frame and shoe is mounted on door.
( )See Figs. 1 & 2
3. Determine the power size required and using the supplied
allen key, adjust door closer strength as per chart on
template. Drill pilot holes in door and frame according to
template. Remove slide plate and fix door closer body with
screws supplied ensuring correct fitting holes are used.
Power adjusting valve must face away from hinge side of
door. (See Figs. 2 & 3)
4. Carefully detach link arm from adjuster arm & securely fix
adjuster arm shoe to door ensuring the shoe is rotated in
the correct position to suit power size required. (See Fig. 4)
Note: Rotate shoe 180°for power size 4
5. Place link arm onto closer spindle at right angles
to door, fit securing screw, move link arm and re-
connect to adjuster arm. (See Figs. 4 & 5)
Note: To adjust arm to suit depth of frame, loosen
nut, adjust arm & re-tighten nut.
6. Fit spindle cover cap to upperside of closer. (See Fig. 5)
7. Check for correct closing & latching speeds and adjust if
necessary. Adjust backcheck as required. (See Fig.6)
8. Stick easi-exit logo onto indent of slide plate and refit to
door closer. (See Fig. 6)
Note: For delayed action model DCS2026BCDA, adjust valve as required.


Product specificaties

Merk: Eurospec
Categorie: Niet gecategoriseerd
Model: Easi-Exit DCS2026

Heb je hulp nodig?

Als je hulp nodig hebt met Eurospec Easi-Exit DCS2026 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Eurospec

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd