Eureka Taron Basecamp 4 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Taron Basecamp 4 (2 pagina's) in de categorie Tent. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Contents of Carry bag
Tent body
Tent fly
Pole bag: 2 long straight main poles,
2 shorter curved side brim poles, 1 short straight fly pole
Stake bag: stakes & guyout cords
E!LUMINATE SYSTEM: 2 silver panels
Setting up the Tent Body
1. Spread the tent body out, floor side down. Locate the yellow webbing
stake out loop, as this marks the front of the tent. Also locate the grey fabric
main pole sleeves which cross in the top center of the tent body.
2. Assemble the two main poles (the two long straight poles)
3. Starting at the corner where the yellow webbing stake out loop is, follow
the sewn seam past the plastic clips and insert one of the main poles into
the grey fabric pole sleeve. Continue sliding the pole through the sleeve
until it reaches the black webbing stake out loop at the opposite corner.
Repeat process with second pole & sleeve. Correctly threaded, the poles
will make a large X shape, crossing in the middle of the tent. Confirm the
poles follow the seams of the tent, and the tips are aligned with the corner
webbing stake out loops.
4. Starting with the pole at the yellow webbing stake out loop, insert the tip of
the pole into the grommet (metal ring). Moving to opposite end of pole,
pressure the pole to bend it upwards & insert the pole tip into the grommet.
Repeat process with second pole.
5. Assemble the two side brim poles (the two shorter curved poles).
6.On the sides of the tent, locate the grey fabric sleeves. Insert & slide one
of the side brim poles through the sleeve, inserting the pole tips into the
grommets at each end. On opposite side of tent body, repeat process with
second pole.
7. Walk around the tent and connect all of the black plastic clips to their
respective poles.
8. Secure the tent to the ground using the stakes provided. Start at the
yellow webbing stake out loop, next proceed to opposite corner, and while
firmly pulling on the black webbing stake out loop hammer in the stake.
Repeat process with the other two corners. Also secure with stakes the
black webbing mid-point stake out loops on each side of the tent.
9.The tent body will now be erect, properly tensioned, and secured to the
ground.
Attaching the Fly Sheet
1. Assemble the fly pole (1 short straight pole)
2. Spread the flysheet on the ground with the inside upwards, the V3
small fly vestibule pole at your feet, and the yellow webbing strap with
buckle on your left.
3. Following the sewn seam from the top of the small fly vestibule pole,
locate the black webbing pocket with hook/loop closure, the hook/loop
closure at the top center of the fly, and the black webbing pocket at the
opposite end of the fly.
4. Insert fly pole end into the black webbing pocket at the opposite end
of the fly, secure the pole to the fly with the hook/loop closure at the top
center of the fly, and then secure the final end of the fly pole in the black
webbing pocket with hook/loop closure
5. Matching the fly’s yellow webbing strap to the tent body’s yellow
webbing stake out loop, drape the fly over the tent body, confirming the
inside of the fly is now facing the tent body.
6. Align and center the fly on the tent body so the 4 buckles match, and
the fly’s seams follow the tent body’s poles.
7. On the sides of the tent body, reach under the flysheet and carefully
align and then secure the flysheet’s hook/loop closure to the center of
the side brim pole’s grey fabric sleeve.
8. Locate the reflective webbing guyout loops on the outside of the
flysheet, reaching under the guyout loops, wrap the hook/loop closure
around the pole to secure the fly to the pole structure.
9. Now clip the buckles at each of the four corners, pulling the webbing
through the buckle to tension the fly.
10. Securing the V3 Vestibule: At the front of the tent, locate the two
black webbing stake-out loops on either side of triangular face of the V3
vestibule. Pulling equal tension on each loop, secure each loop with a
stake. To properly tension the V3 vestibule during staking, reach under
the fly & push the ground-level end of the V3’s pole away from you.
When completed, the V3’s small vestibule pole will be at approximately
a 45 degree angle from the ground when viewed from the side with the
door opened. During extreme weather, anchor the inside tip of the V3
small vestibule pole with a stake through the black webbing loop.
Additionally tie a provided guyout cord to reflective webbing guyout loop
and secure with a stake.
11. Securing the rear vestibule: for increased versatility in configuring
the vestibule, four adjustable stake out loops are provided. Minimally,
stake the two outermost stake out loops, adjusting the tension by pulling
the webbing through the triglide buckle.
E!Luminate System:
Increases the brightness of floor-level lighting provided by LED lanterns
inside the tent. Two removable triangular silver-reflective E!Luminate panels
install in the ceiling with small webbing loops & toggles and reflect a lantern’s
light downwards to the floor, increasing the brightness of floor-level light up to
3 times. A reinforced webbing hang loop with D-ring securely holds LED
lanterns at the tent’s peak. An elegant, yet simple & effective solution to
brighten the nighttime camping experience.
NOTE: Only for use with battery powered LED lanterns.
Dry Entry Marker: Located on the front V3 Vestibule door, keep rain out
of the tent when entering/exiting by stopping the fly’s zipper at the reflective
webbing marker
Snivel Locks: both front and rear vestibules’ door panels lock at bottom
with a side-release buckle to eliminate wind-driven opening
V3 Enhanced Tent System:
A series of individual features which create a system that enhances a tent’s
utility and comfort in the backcountry. This synergistic system is called the
V3-Enhanced Tent System.There are three primary design components to
the V3 Enhanced Tent System: the vertical strut vestibule pole, vectored
fly-to-tent-body pullouts, and hooded fly vents. Each design feature offers
several individual performance benefits, but when incorporated into a single
tent, a synergistic effect is observed.
12. Vectored Side Pullouts: As part of the V3 System, this tent features
fly-to-tent body pullouts. At the mid-point on each side of the tent, reach
under the fly’s edge, slide the black “dog bone” toggle through the
“O-Ring” located on the tent body. Attach a provided guyout cord to the
small webbing loop. Secure guyout cord with a stake. Repeat process
on other side of tent. The Vectored Side Pullouts enhance ventilation,
increase the tent’s interior living space, and strengthen the overall tent
during inclement weather.
13. Guyouts: This tent features preinstalled equalized guyouts.
Get in the habit of always using the guyouts even in good weather.
Eureka! Set-Up Instructions
Taron Basecamp 4 person (#2629041) &
Taron Basecamp 6 person (#2629043) Tents
Good:
4 stakes /4 lines
Best:
4 stakes /8 lines
REV 082013
SEAM SEALING:
We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett
Outdoor SeamGrip
®
.
• Work in a fully ventilated area.
• Set the tent up or lay the tent out flat. Taut seams allow for even
application and penetration of the sealer.
• Decide which seams need to be sealed. For example, seams that will be
exposed to rain, runo, or ground level water are a must for sealing, while
seams on uncoated nylon or mesh panels don’t need treatment. There is
no need to seal the seams in the roof or the factory taped seams. We
recommend sealing both floor and fly seams and reinforcements.
• Apply sealant to the inside and outside of all exposed seams. Several thin
layers will work better than one thick layer. Read and follow
manufacture's instructions.
STAKING:
All tents need to be staked down to keep them from blowing away.
Securing the tent by placing heavy objects inside is just not adequate.
• Once the tent body is erected, stake it out before the fly is put on. This
enables you to square the tent up to ensure that the fly goes on properly
and that the seams align with the frame. Pull the base of the tent taut
between each web stake out loop or ring & pin. Make sure that all corners
are square. It is important that you don’t stake the tent out too tightly.
You will know it’s too tight, if the door zippers can not be easily operated.
Drive stakes through the web loops, or with ring & pin, drive the stake
just outside the ring so that the “J” hook catches it. Tie a piece of cord or
web into a loop through the ring to be used as a large stake loop if
needed.
• With the tent properly staked, drape the fly over the frame, attach its tent
connection points and stake down any pull outs.
• Do not attempt to remove the stakes by pulling on the tent becket loop,
as this could cause the fabric to tear. The best way is to pry on the stake
itself.
STAKING IN SPECIAL CONDITIONS:
• Sand. Use long, broad stakes with plenty of surface area in loose soil.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes
separately. Their sharp edges can cut fabric and leave rust stains, which
might damage your tent.
• Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent
bags, or stu sacks filled with snow; or tie tents to snow shoes, skis, or ski
poles, which are stuck in the snow.
GUY LINES:
Do not depend upon staking alone to keep your tent secure during high
winds. Most tent models have built-in loops or rings at optimal guy out
locations. It’s important to put in the extra time guying out your tent.
Correctly done, it can save your tent during exceptional weather.
• Make sure that the top fly is securely attached to the tent frame. Ties, hook
and loop, or dog-bones and elastic loops are sewn to the underside of the
fly for this purpose.
• Attach parachute cord to the loops/rings and stake them in the ground
three or four feet from the edge of the tent. If staked too close to the tent,
wind can cause an upward pull that could dislodge the stakes.
• If your tent does not have loops or rings for guy outs, attach guy lines 1/3
to 1/2 of the way up the framework on the main sidewalls. This enables
the guy line to support the lower section of the pole, while the upper
pole can flex and deflect wind gusts. It is best to run two cords at an
angle from the side of the guy out. This prevents all movement, except
toward the anchor. The guy lines will work together through opposition.
See illustrations.
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of
water overnight. If it cannot escape, the water vapor condenses to liquid.
Most often, water found in the tent is a result of this condensation rather
than from the tent leaking. Condensation often forms where the sleeping
bag touches the side of the tent, under the sleeping pad, or on coated
surfaces such as the door flaps. A tent’s double wall construction allows
the vapor to escape through the roof to the outside, keeping the inside of
the tent dry.
Leave the windows partially open at night to provide cross ventilation and
further reduce condensation. Cross ventilation becomes more important
in very humid or extremely cold conditions when the permeable roof is
less effective. The features that enhance ventilation are windows,
short-sheeted flys (bottom venting), roof vents, and High/Low venting
doors. These are specific to each tent model.
Given the importance of proper ventilation, We use High/Low venting in
most of our tents. This allows cooler air in through the low vents and
warmer, moist air up and out through the high vents. High/Low venting is
accomplished within the inner tent via roof vents, doors and windows. It
is important to vent the vestibule. Unvented, it can inhibit airflow into the
tent. Our tent vestibules profit from the ability to “short sheet” by means
of zippers & toggles and staked vestibule pull outs create a bellowing
effect.
Most of our tents are equipped with a High/Low venting door. This design
allows increased airflow into the tent from the bottom. Open the low
vent/window to admit cool air, allowing the warmer air out through the
high roof vents. When rain and wind prevent the low vent from being
opened, the high door vent can still be used. Fly overhangs or vestibules
protect it.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to tent fabric is caused by excessive exposure to
sunlight. While our fabrics are UV resistant, any synthetic fabric is
susceptible to UV degradation. UV damage will cause nylon and polyester
to become brittle and tear easily. We recommend that you use the rain fly
even on clear days. It acts as a sunscreen to the tent. A rain fly is both
easier and less expensive to replace if damaged. UV damage can be
minimized by erecting tents on shaded sites with low exposure to direct
sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag
on its end to get the tent out. These actions may cut the shock cord and
damage the pole ends.
• The aluminum frame may bend slightly and take a “set” through usage;
this normally does not affect the performance of the frame.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
• Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
• Do not keep food inside a tent. Hungry critters will chew through
tent fabric in search of food.
STORAGE:
• Make sure the tent is completely dry, then store loosely rolled, in a
dry, cool place. To prevent dust from collecting on the tent, cover it
with a cloth. This allows the nylon/polyester fabric to breathe.
• Ideally, the tent poles should be stored in their fully assembled state.
This reduces the tension on the shock cord, prolonging its life.
• The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
• Do to the nature of tent fabrics, color can transfer from darker to
lighter fabrics when the two fabrics are in contact over time when
wet, damp or exposed to the combination of moisture and high
heat. This does not eect the tent's performance. To prevent /
minimize color transfer, always make sure your tent is completely dry
prior to packing and storage.
CLEANING:
• Clean the tent by setting it up and wiping it down with a mild soap
(liquid hand soap) and lukewarm water solution. Rinse thoroughly
and dry completely. Never use detergent, washing machines or
dryers because they can damage the tent’s protective coating and
seams. After cleaning, be sure the tent is completely dry, especially
the heavier, double-stitched areas such as the seams, before storing
or mold / mildew are likely to grow.
• Clean the tent poles with a cloth and lubricate them with silicone
spray. This is especially necessary after ocean side camping to
remove salt spray so the poles don’t corrode or stay gritty.
• Clean the zippers with a quick dip in water and then dry them o.
This is especially important if you’ve been camping in a location with
sand/dirt. If you don’t clean the zippers, the sliders will wear out and
eventually the teeth will become inoperable.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its
condition at the time of sale. Alteration, modication or any use of
this product contrary to the accompanying written instructions shall
void the warranty. Moreover, any misuse, alteration or modication
of the product shall absolve Johnson Outdoors Gear LLC of any
liability for property damages or injuries sustained as a result of such
misuse, modication or alteration.
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear LLC
warrants to the original
purchaser that its products are free from defects in material and
workmanship, for the life of the product, except as qualified below. The
life of the product is determined from the date of purchase until such
time as the product is no longer serviceable due to normal wear and
tear.
What Is Not Covered:
Johnson Outdoors Gear LLC
shall not be responsible
for the natural breakdown of materials that occurs inevitably with
extended use (e.g., Ultra Violet (UV) light damage on tents, exhausted
zippers), or defects caused by accident, abuse, alteration, animal attack,
storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS
OF THIS LIMITED WARRANTY.
IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
What Johnson Outdoors Gear LLC Will Do: If after
inspection we find that a product failed due to a
manufacturing or material defect, we will repair or
replace the product, at our option, without charge.
How to Obtain Warranty Service: Return the product,
freight prepaid, to the Dealer from whom it was
purchased; or, contact our Customer Satisfaction
Department for return authorization: toll free
1-800-572-8822. Collect shipments or shipments without
return authorization cannot be accepted. The product
registration card packaged with our product need not
be returned for the warranty to be eective and for you
to receive warranty service.
Repairs: If your
Johnson Outdoors Gear LLC
product
needs service or repair due to normal wear and tear,
animal attack, accident or some other reason that is not
covered under the warranty we will provide the
necessary service for a reasonable charge, plus shipping
and handling. We require that products accepted for any
repair be properly cleaned according to our
recommended care instructions. Please send your
product or component that requires
repair (e.g., tent fly),
postage prepaid, along with a description of what needs
attention. For service and repairs, please contact our
Customer Satisfaction Department: toll free
1-800-572-8822
How State Law Relates To This Warranty: This warranty gives
you specific legal rights, and you may have other rights
that vary from state to state.
Our brands are part of the Johnson Outdoors
family of products. Visit all the brands at
johnsonoutdoors.com
We support the "Leave No Trace" Seven
Principles:
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7 . BE COURTEOUS OF OTHER VISITORS
JOHNSON OUTDOORS GEAR INC
WARNING:
KEEP ALL FLAME AND HEAT SOURCES
AWAY FOM THIS TENT!
This tent meets the ammability requirements of CPAI-84. The Fabric may burn
if continuous cntact with any ame source. Do NOT operate any device which
burns fuel inside your tent. This could lead to serious injury or death.
Product specificaties
| Merk: | Eureka |
| Categorie: | Tent |
| Model: | Taron Basecamp 4 |
Heb je hulp nodig?
Als je hulp nodig hebt met Eureka Taron Basecamp 4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Tent Eureka
2 Juni 2023
15 Mei 2023
13 Mei 2023
12 Mei 2023
10 Mei 2023
7 Mei 2023
6 Mei 2023
4 Mei 2023
3 Mei 2023
2 Mei 2023
Handleiding Tent
- Tent Philips
- Tent IKEA
- Tent Asaklitt
- Tent Babymoov
- Tent Bestway
- Tent Brunner
- Tent Dometic
- Tent Dwt-Zelte
- Tent Fiamma
- Tent Gerjak
- Tent Mx Onda
- Tent Perel
- Tent Rocktrail
- Tent Rollei
- Tent Skandika
- Tent Thule
- Tent Trigano
- Tent Velleman
- Tent Ventura
- Tent Walker
- Tent Woods
- Tent Jamet
- Tent Obelink
- Tent Crivit
- Tent Edges
- Tent Kayoba
- Tent Hamron
- Tent Big Agnes
- Tent Black Diamond
- Tent Camp Master
- Tent Camp Trails
- Tent Carl Denig
- Tent Chinook
- Tent Coleman
- Tent De Waard
- Tent Easy Camp
- Tent High Peak
- Tent Hilleberg
- Tent Jack Wolfskin
- Tent Kelty
- Tent Khyam
- Tent Mountain Hardwear
- Tent Nigor
- Tent Nomad
- Tent Outwell
- Tent OZtrail
- Tent Raclet
- Tent Robens
- Tent Sierra Designs
- Tent Trimm
- Tent Vango
- Tent Vaude
- Tent Vrijbuiter
- Tent Wechsel
- Tent Wilderness Equipment
- Tent Wynnster
- Tent Zempire
- Tent SereneLife
- Tent Aart Kok
- Tent Cabanon
- Tent Holtkamper
- Tent Goldcamp
- Tent Isabella
- Tent Thermex
- Tent Kathmandu
- Tent Sorara
- Tent MSR
- Tent LECO
- Tent TOOLPORT
- Tent Helsport
- Tent Robinhood
- Tent Casaria
- Tent Black Wolf
- Tent Nordisk
- Tent Grand Canyon
- Tent San Hima
- Tent Gazebo Penguin
- Tent Sojag
- Tent Calima
- Tent Yamazen
Nieuwste handleidingen voor Tent
14 December 2024
5 December 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024