Eureka Jade Canyon 4 Handleiding

Eureka Tent Jade Canyon 4

Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Jade Canyon 4 (2 pagina's) in de categorie Tent. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Contents of Carry bag
Tent body
Tent fly
Pole bag:4 steel straight poles (leg poles)
2 long bright green aluminum poles (roof poles)
Stake bag: 8 steel skewer stakes
E!LUMINATE SYSTEM: 2 silver panels
Eureka! Media Center (gear hammock with clear panel)
Gear Hammock
1. Spread the tent body out, floor side down. Locate the yellow webbing
stake out loop, as this marks the right front corner of the tent. Also locate
the black plastic elbow hub & grey fabric roof pole sleeves which cross in the
top center of the tent body.
2. Assemble the two bright green aluminum roof poles
3. Starting at the corner with the yellow webbing stake out loop, follow the
sewn seam past the plastic hub and insert one of the poles into the grey
fabric pole sleeve. Continue sliding the pole through the sleeve until it
reaches the black plastic hub at the opposite corner. Insert the pole ends
into the hub opening which has internal ribs. (NOTE: the other hub opening
is smooth & is used for the larger diameter leg poles.) Repeat process with
the second pole & sleeve. Correctly threaded, the poles will make a large X
shape, crossing in the middle of the tent.
4. Assemble the four leg poles & place one at each corner of the tent.
5. Starting at the yellow webbing stake out loop, insert the open end of the
leg pole into the smooth opening of the black plastic hub. Raising the pole &
hub, reach down and insert the tip of the pole into the outer-most grommet
(metal ring) on yellow webbing stake out loop. Moving to another corner,
repeat process with second pole, then a third, & lastly the fourth. Your tent
will now be standing.
6. Walk around the tent and connect all of the black plastic clips to their
respective poles.
Attaching the Fly Sheet
1. Unfold the fly & drape it over the tent matching the yellow
webbing on the fly with the yellow webbing on the tent body.
Align and center the fly on the tent body so the fly’s seams follow
the tent body’s poles.
2. Clip together the side-release buckle on the yellow webbing,
joining the fly to the tent body.
3. Locate the bright green triangular wing at the upper corner of
the fly. Reaching under the wing, wrap the hook/loop closure
around the underlying pole to secure the fly to the pole. Farther
down the pole & fly is another the hook/loop closure. Also wrap
this hook/loop closure around the pole to secure the fly to the
pole.
4. Repeat wrapping the hook/loop closures around all of the
three remaining leg poles to secure the fly to the tent’s pole
structure.
5. Clip together the side-release buckle on the three remaining
black webbing stake out loops.
6. Walk around the tent & equally tension all four corner
webbings by pulling the webbing through the buckle to tension
the fly.
7. Guyouts: The bright green triangular wings also contain
pockets which store the pre-attached guyout cords. Remove the
cord from the pocket & extend it to full length. Secure the guyout
cord to the ground with a stake. In high winds, an additional
guyout cord can be attached to the small black webbing loop
halfway up the leg pole. Get in the habit of always using the
guyouts even in good weather.
7. Secure the tent to the ground using the stakes provided. Start at the
yellow webbing stake out loop, next proceed to the diagonally opposite
corner. While firmly pulling on the black webbing stake out loop,
hammer in the stake. Repeat process with the other two corners.
8. The tent body will now be erect, properly tensioned, and secured to
the ground.
Eureka! Set-Up Instructions
Jade Canyon 4 (#2601276)
Jade Canyon 6 (#2601281)
REV 082714
Setting up the Tent Body
E!Luminate System:
Increases the brightness of floor-level lighting provided by LED lanterns
inside the tent. Two removable triangular silver-reflective E!Luminate
panels install in the ceiling with O-rings & toggles The panels reflect a
lantern’s light downwards to the floor, increasing the brightness of
floor-level light up to 3 times. A reinforced webbing hang loop with D-ring
securely holds LED lanterns at the tent’s peak. An elegant, yet simple &
effective solution to brighten the nighttime camping experience.
NOTE: Only for use with battery powered LED lanterns.
EUREKA! Media Center:
Watch video on tablets & other small electronic devices from the comfort
of your sleeping bag. The clear center panel of the Media Center is
touchscreen friendly. The Media Center attaches with hooks to pre-in-
stalled O-rings located in each corner of the tent. Also secure the center
of the Media Center with the cord & hook to support heavier items.
Gear Hammock:
The gear hammock attaches with hooks to pre-installed O-rings located
in each corner of the tent. Secure the center of the hammock with the
cord & hook to support heavier items.
E! Power Port:
The zippered E! Power Port allows you to bring an electrical power cord
inside the tent.
Good:
4 stakes /4 lines
Best:
4 stakes /8 lines
SEAM SEALING:
We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett
Outdoor SeamGrip
®
.
Work in a fully ventilated area.
Set the tent up or lay the tent out flat. Taut seams allow for even
application and penetration of the sealer.
Decide which seams need to be sealed. For example, seams that will be
exposed to rain, runoff, or ground level water are a must for sealing, while
seams on uncoated nylon or mesh panels don’t need treatment. There is
no need to seal the seams in the roof or the factory taped seams. We
recommend sealing both floor and fly seams and reinforcements.
Apply sealant to the inside and outside of all exposed seams. Several thin
layers will work better than one thick layer. Read and follow
manufacture's instructions.
STAKING:
All tents need to be staked down to keep them from blowing away.
Securing the tent by placing heavy objects inside is just not adequate.
Once the tent body is erected, stake it out before the fly is put on. This
enables you to square the tent up to ensure that the fly goes on properly
and that the seams align with the frame. Pull the base of the tent taut
between each web stake out loop or ring & pin. Make sure that all corners
are square. It is important that you don’t stake the tent out too tightly.
You will know its too tight, if the door zippers can not be easily operated.
Drive stakes through the web loops, or with ring & pin, drive the stake
just outside the ring so that the J” hook catches it. Tie a piece of cord or
web into a loop through the ring to be used as a large stake loop if
needed.
• With the tent properly staked, drape the fly over the frame, attach its tent
connection points and stake down any pull outs.
Do not attempt to remove the stakes by pulling on the tent becket loop,
as this could cause the fabric to tear. The best way is to pry on the stake
itself.
STAKING IN SPECIAL CONDITIONS:
• Sand. Use long, broad stakes with plenty of surface area in loose soil.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes
separately. Their sharp edges can cut fabric and leave rust stains, which
might damage your tent.
Snow. Use dead man” anchors. Tie tent to buried objects (branches, tent
bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski
poles, which are stuck in the snow.
GUY LINES:
Do not depend upon staking alone to keep your tent secure during high
winds. Most tent models have built-in loops or rings at optimal guy out
locations. It’s important to put in the extra time guying out your tent.
Correctly done, it can save your tent during exceptional weather.
• Make sure that the top fly is securely attached to the tent frame. Ties, hook
and loop, or dog-bones and elastic loops are sewn to the underside of the
fly for this purpose.
Attach parachute cord to the loops/rings and stake them in the ground
three or four feet from the edge of the tent. If staked too close to the tent,
wind can cause an upward pull that could dislodge the stakes.
• If your tent does not have loops or rings for guy outs, attach guy lines 1/3
to 1/2 of the way up the framework on the main sidewalls. This enables
the guy line to support the lower section of the pole, while the upper
pole can flex and deflect wind gusts. It is best to run two cords at an
angle from the side of the guy out. This prevents all movement, except
toward the anchor. The guy lines will work together through opposition.
See illustrations.
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of
water overnight. If it cannot escape, the water vapor condenses to liquid.
Most often, water found in the tent is a result of this condensation rather
than from the tent leaking. Condensation often forms where the sleeping
bag touches the side of the tent, under the sleeping pad, or on coated
surfaces such as the door flaps. A tents double wall construction allows
the vapor to escape through the roof to the outside, keeping the inside of
the tent dry.
Leave the windows partially open at night to provide cross ventilation and
further reduce condensation. Cross ventilation becomes more important
in very humid or extremely cold conditions when the permeable roof is
less effective. The features that enhance ventilation are windows,
short-sheeted flys (bottom venting), roof vents, and High/Low venting
doors. These are specific to each tent model.
Given the importance of proper ventilation, We use High/Low venting in
most of our tents. This allows cooler air in through the low vents and
warmer, moist air up and out through the high vents. High/Low venting is
accomplished within the inner tent via roof vents, doors and windows. It
is important to vent the vestibule. Unvented, it can inhibit airflow into the
tent. Our tent vestibules profit from the ability to “short sheet” by means
of zippers & toggles and staked vestibule pull outs create a bellowing
effect.
Most of our tents are equipped with a High/Low venting door. This design
allows increased airflow into the tent from the bottom. Open the low
vent/window to admit cool air, allowing the warmer air out through the
high roof vents. When rain and wind prevent the low vent from being
opened, the high door vent can still be used. Fly overhangs or vestibules
protect it.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to tent fabric is caused by excessive exposure to
sunlight. While our fabrics are UV resistant, any synthetic fabric is
susceptible to UV degradation. UV damage will cause nylon and polyester
to become brittle and tear easily. We recommend that you use the rain fly
even on clear days. It acts as a sunscreen to the tent. A rain fly is both
easier and less expensive to replace if damaged. UV damage can be
minimized by erecting tents on shaded sites with low exposure to direct
sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag
on its end to get the tent out. These actions may cut the shock cord and
damage the pole ends.
The aluminum frame may bend slightly and take a “set through usage;
this normally does not affect the performance of the frame.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
Do not keep food inside a tent. Hungry critters will chew through
tent fabric in search of food.
STORAGE:
Make sure the tent is completely dry, then store loosely rolled, in a
dry, cool place. To prevent dust from collecting on the tent, cover it
with a cloth. This allows the nylon/polyester fabric to breathe.
Ideally, the tent poles should be stored in their fully assembled state.
This reduces the tension on the shock cord, prolonging its life.
The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
Do to the nature of tent fabrics, color can transfer from darker to
lighter fabrics when the two fabrics are in contact over time when
wet, damp or exposed to the combination of moisture and high
heat. This does not effect the tent's performance. To prevent /
minimize color transfer, always make sure your tent is completely dry
prior to packing and storage.
CLEANING:
Clean the tent by setting it up and wiping it down with a mild soap
(liquid hand soap) and lukewarm water solution. Rinse thoroughly
and dry completely. Never use detergent, washing machines or
dryers because they can damage the tent’s protective coating and
seams. After cleaning, be sure the tent is completely dry, especially
the heavier, double-stitched areas such as the seams, before storing
or mold / mildew are likely to grow.
Clean the tent poles with a cloth and lubricate them with silicone
spray. This is especially necessary after ocean side camping to
remove salt spray so the poles don’t corrode or stay gritty.
Clean the zippers with a quick dip in water and then dry them off.
This is especially important if youve been camping in a location with
sand/dirt. If you don’t clean the zippers, the sliders will wear out and
eventually the teeth will become inoperable.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its
condition at the time of sale. Alteration, modication or any use of
this product contrary to the accompanying written instructions shall
void the warranty. Moreover, any misuse, alteration or modication
of the product shall absolve Johnson Outdoors Gear LLC of any
liability for property damages or injuries sustained as a result of such
misuse, modication or alteration.
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear LLC
warrants to the original
purchaser that its products are free from defects in material and
workmanship, for the life of the product, except as qualified below. The
life of the product is determined from the date of purchase until such
time as the product is no longer serviceable due to normal wear and
tear.
What Is Not Covered:
Johnson Outdoors Gear LLC
shall not be responsible
for the natural breakdown of materials that occurs inevitably with
extended use (e.g., Ultra Violet (UV) light damage on tents, exhausted
zippers), or defects caused by accident, abuse, alteration, animal attack,
storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS
OF THIS LIMITED WARRANTY.
IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
What Johnson Outdoors Gear LLC Will Do: If after
inspection we find that a product failed due to a
manufacturing or material defect, we will repair or
replace the product, at our option, without charge.
How to Obtain Warranty Service: Return the product,
freight prepaid, to the Dealer from whom it was
purchased; or, contact our Customer Satisfaction
Department for return authorization: toll free
1-800-572-8822. Collect shipments or shipments without
return authorization cannot be accepted. The product
registration card packaged with our product need not
be returned for the warranty to be effective and for you
to receive warranty service.
Repairs: If your
Johnson Outdoors Gear LLC
product
needs service or repair due to normal wear and tear,
animal attack, accident or some other reason that is not
covered under the warranty we will provide the
necessary service for a reasonable charge, plus shipping
and handling. We require that products accepted for any
repair be properly cleaned according to our
recommended care instructions. Please send your
product or component that requires
repair (e.g., tent fly),
postage prepaid, along with a description of what needs
attention. For service and repairs, please contact our
Customer Satisfaction Department: toll free
1-800-572-8822
How State Law Relates To This Warranty: This warranty gives
you specific legal rights, and you may have other rights
that vary from state to state.
Our brands are part of the Johnson Outdoors
family of products. Visit all the brands at
johnsonoutdoors.com
We support the "Leave No Trace" Seven
Principles:
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7 . BE COURTEOUS OF OTHER VISITORS
JOHNSON OUTDOORS GEAR INC
WARNING:
KEEP ALL FLAME AND HEAT SOURCES
AWAY FOM THIS TENT!
This tent meets the ammability requirements of CPAI-84. The Fabric may burn
if continuous cntact with any ame source. Do NOT operate any device which
burns fuel inside your tent. This could lead to serious injury or death.
REV 082714


Product specificaties

Merk: Eureka
Categorie: Tent
Model: Jade Canyon 4

Heb je hulp nodig?

Als je hulp nodig hebt met Eureka Jade Canyon 4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Tent Eureka

Handleiding Tent

Nieuwste handleidingen voor Tent