Eureka Sunrise EX 4 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Sunrise EX 4 (2 pagina's) in de categorie Tent. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Contents of Carry bag
Tent body
Tent fly
Pole Bag: 2 long main poles, 2 shorter ridge poles
Stake bag: Stakes and guy-out cords
E!Luminate System: 2 reflective panels
Eureka! Media Center
Fabric Divider Curtain ( ) #2629186 Sunrise EX 8 only
Setting up the Tent Body
1. Spread out the tent body, floor side down. Locate the yellow webbing
corner loop, as this marks the front right hand corner of the tent.
2. Assemble the two long main poles by inserting each pole section into the
corresponding metal ferrule.
3. Starting at the corner with the yellow webbing, place one end of the pole
into the metal grommet at webbing end, then place the pole diagonally
across the tent. From the opposite corner, apply pressure to the pole to
bend it and insert the pole end into the corresponding metal grommet.
Repeat this process with second long main pole by securing one end into
the corner metal grommet before then securing the opposite end.
4. Raise the two main poles and attach the tent where the poles cross, using
the fabric loop and toggle.
5. Walk around the tent and attach the tent body to the poles by clipping
each of the black plastic fasteners.
6. Assemble the two short length ridge poles by inserting each pole section
into the corresponding metal ferrule.
7. Starting above the tent door, grab the grey webbing and place one end of
the short ridge pole through the grommet on the grey webbing while laying
the ridge pole across the top of the tent. From the opposite side, place the
opposite end of ridge pole through corresponding grommet by holding onto
grey webbing loop.
Attaching the Fly Sheet
1. Locate the yellow webbing end corner of fly sheet to indicate the front
right corner orientation.
2. Place fly sheet over the top of the tent and all poles, aligning and
centering the fly on the tent body so the four bungee cords with hooks
mate with the stake out loops and D-Rings at each of the four corners of
the tent.
3. On the underside of the flysheet, locate the four black webbing
pockets at the center of each side. Insert each of the ridge pole ends
into its respective pocket by opening the hook and loop attachment
before securing around the ridge pole end assembly.
4. Ensure that all 4 bungee cords with hooks are clipped to the D-Rings
at each of the four tent corners.
5. Four guy out cords are included within your stake bag. We recom-
mend always using the guy out cords to secure your tent, as weather
conditions may change rapidly. Tie the guy lines to webbing loops on
the fly at each of the four corner poles of the tent and secure this line to
a staked out position or nearby object.
E!Luminate System:
Increases the brightness of floor-level lighting provided by LED lanterns
inside the tent. Two removable triangular silver-reflective E!Luminate panels
install in the ceiling with small webbing loops & toggles and reflect a lantern’s
light downwards to the floor, increasing the brightness of floor-level light up to
3 times. A reinforced webbing hang loop with D-ring securely holds LED
lanterns at the tent’s peak. An elegant, yet simple & effective solution to
brighten the nighttime camping experience.
NOTE: Only for use with battery powered LED lanterns.
EUREKA! Media Center:
Watch video on tablets & other small electronics from the comfort of your
sleeping bag. The clear center panel of the Media Center is touchscreen
friendly. The Media Center attaches with hooks to pre-installed webbing
loops located in each corner of the tent.
Eureka! Set-Up Instructions
Sunrise EX 4 (#2629182)
Sunrise EX 6 (#2629184)
Sunrise EX 8 (#2629186)
REV 091115
8. Repeat this process with the second ridge pole.
9. Attach the remaining black plastic fasteners by attaching them to the
two ridge poles
10. Secure the tent to the ground using the provided stakes. Starting at
the yellow webbing corner, drive the stake through the webbing loop
and into the ground. Next proceed to the opposite corner and repeat
this process after firmly pulling the tent tout. Proceed to repeat this
process for the remaining corners, taking care to equalize tension
between all sides.
Good:
4 stakes /4 lines Best:
4 stakes /8 lines
SEAM SEALING:
We recommend use of a sealer such as Kenyon Seam Sealer 3 or
McNett Outdoor SeamGrip
®.
• Work in a fully ventilated area.
• Set the tent up or lay the tent out flat. Taut seams allow for even
application and penetration of the sealer.
• Decide which seams need to be sealed. For example, seams that will be
exposed to rain, runoff, or ground level water are a must for sealing,
while seams on uncoated nylon or mesh panels don’t need treatment.
There is no need to seal the seams in the roof or the factory taped
seams. We recommend sealing both floor and fly seams and
reinforcements.
• Apply sealant to the inside and outside of all exposed seams. Several
thin layers will work better than one thick layer. Read and follow
manufacturer's instructions.
STAKING:
All tents need to be staked down to keep them from blowing away.
Securing the tent by placing heavy objects inside is just not adequate.
• Once the tent body is erected, stake it out before the fly is put on. This
enables you to square the tent up to ensure that the fly goes on properly
and that the seams align with the frame. Pull the base of the tent taut
between each web stake out loop or ring & pin. Make sure that all
corners are square. It is important that you don’t stake the tent out too
tightly. You will know it’s too tight, if the door zippers can not be easily
operated. Drive stakes through the web loops, or with ring & pin, drive
the stake just outside the ring so that the “J” hook catches it. Tie a piece
of cord or web into a loop through the ring to be used as a large stake
loop if needed.
• With the tent properly staked, drape the fly over the frame, attach its tent
connection points and stake down any pull outs.
• Do not attempt to remove the stakes by pulling on the tent stake-out loop, as
this could cause the fabric to tear. The best way is to pry on the stake itself.
STAKING IN SPECIAL CONDITIONS:
• Sand. Use long, broad stakes with plenty of surface area in loose soil.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes
separately. Their sharp edges can cut fabric and leave rust stains, which
might damage your tent.
• Snow. Use “dead man” anchors. Tie tent to buried objects (branches,
tent bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis,
or ski poles, which are stuck in the snow.
GUY LINES:
Do not depend upon staking alone to keep your tent secure during high
winds. Most tent models have built-in loops or rings at optimal guy out
locations. It’s important to put in the extra time guying out your tent.
Correctly done, it can save your tent during exceptional weather.
• Make sure that the top fly is securely attached to the tent frame. Ties,
hook and loop, or dog-bones and elastic loops are sewn to the
underside of the fly for this purpose.
• Attach parachute cord to the loops/rings and stake them in the ground
three or four feet from the edge of the tent. If staked too close to the tent,
wind can cause an upward pull that could dislodge the stakes.
• If your tent does not have loops or rings for guy outs, attach guy lines 1/3
to 1/2 of the way up the framework on the main sidewalls. This enables
the guy line to support the lower section of the pole, while the upper pole
can flex and deflect wind gusts. It is best to run two cords at an angle
from the side of the guy out. This prevents all movement, except toward
the anchor. The guy lines will work together through opposition. See
illustrations.
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of water
overnight. If it cannot escape, the water vapor condenses to liquid. Most
often, water found in the tent is a result of this condensation rather than
from the tent leaking. Condensation often forms where the sleeping bag
touches the side of the tent, under the sleeping pad, or on coated
surfaces such as the door flaps. A tent’s double wall construction allows
the vapor to escape through the roof to the outside, keeping the inside of
the tent dry.
Leave the windows partially open at night to provide cross ventilation and
further reduce condensation. Cross ventilation becomes more important
in very humid or extremely cold conditions when the permeable roof is
less effective. The features that enhance ventilation are windows,
short-sheeted flys (bottom venting), roof vents, and High/Low venting
doors. These are specific to each tent model.
Given the importance of proper ventilation, We use High/Low venting in
most of our tents. This allows cooler air in through the low vents and
warmer, moist air up and out through the high vents. High/Low venting is
accomplished within the inner tent via roof vents, doors and windows. It
is important to vent the vestibule. Unvented, it can inhibit airflow into the
tent. Our tent vestibules profit from the ability to “short sheet” by means
of zippers & toggles and staked vestibule pull outs create a bellowing
effect.
Most of our tents are equipped with a High/Low venting door. This design
allows increased airflow into the tent from the bottom. Open the low
vent/window to admit cool air, allowing the warmer air out through the
high roof vents. When rain and wind prevent the low vent from being
opened, the high door vent can still be used. Fly overhangs or vestibules
protect it.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to tent fabric is caused by excessive exposure to
sunlight. While our fabrics are UV resistant, any synthetic fabric is
susceptible to UV degradation. UV damage will cause nylon and
polyester to become brittle and tear easily. We recommend that you use
the rain fly even on clear days. It acts as a sunscreen to the tent. A rain
fly is both easier and less expensive to replace if damaged. UV damage
can be minimized by erecting tents on shaded sites with low exposure to
direct sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag
on its end to get the tent out. These actions may cut the shock cord and
damage the pole ends.
• The aluminum frame may bend slightly and take a “set” through usage;
this normally does not affect the performance of the frame.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
• Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
• Do not keep food inside a tent. Hungry critters will chew through
tent fabric in search of food.
STORAGE:
• Make sure the tent is completely dry, then store loosely rolled, in a
dry, cool place. To prevent dust from collecting on the tent, cover it
with a cloth. This allows the nylon/polyester fabric to breathe.
• Ideally, the tent poles should be stored in their fully assembled state.
This reduces the tension on the shock cord, prolonging its life.
• The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
• Do to the nature of tent fabrics, color can transfer from darker to
lighter fabrics when the two fabrics are in contact over time when
wet, damp or exposed to the combination of moisture and high
heat. This does not effect the tent's performance. To prevent /
minimize color transfer, always make sure your tent is completely
dry prior to packing and storage.
CLEANING:
• Clean the tent by setting it up and wiping it down with a mild soap
(liquid hand soap) and lukewarm water solution. Rinse thoroughly
and dry completely. Never use detergent, washing machines or
dryers because they can damage the tent’s protective coating and
seams. After cleaning, be sure the tent is completely dry, especially
the heavier, double-stitched areas such as the seams, before
storing or mold / mildew are likely to grow.
• Clean the tent poles with a cloth and lubricate them with silicone
spray. This is especially necessary after ocean side camping to
remove salt spray so the poles don’t corrode or stay gritty.
• Clean the zippers with a quick dip in water and then dry them off.
This is especially important if you’ve been camping in a location
with sand/dirt. If you don’t clean the zippers, the sliders will wear out
and eventually the teeth will become inoperable.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its
condition at the time of sale. Alteration, modification or any use of
this product contrary to the accompanying written instructions shall
void the warranty. Moreover, any misuse, alteration or modification
of the product shall absolve Johnson Outdoors Gear, Inc. of any
liability for property damages or injuries sustained as a result of
such misuse, modification or alteration.
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear, Inc.
warrants to the original
purchaser that its products are free from defects in material and
workmanship, for the life of the product, except as qualified below. The
life of the product is determined from the date of purchase until such
time as the product is no longer serviceable due to normal wear and
tear.
What Is Not Covered:
Johnson Outdoors Gear, Inc.
shall not be
responsible for the natural breakdown of materials that occurs
inevitably with extended use (e.g., Ultra Violet (UV) light damage on
tents, exhausted zippers), or defects caused by accident, abuse,
alteration, animal attack, storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE
TERMS OF THIS LIMITED WARRANTY.
IN NO EVENT SHALL JOHNSON OUTDOORS GEAR
INC. BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
What Johnson Outdoors Gear, Inc. Will Do: If after
inspection we find that a product failed due to a
manufacturing or material defect, we will repair or
replace the product, at our option, without charge.
How to Obtain Warranty Service: Return the product,
freight prepaid, to the Dealer from whom it was
purchased; or, contact our Customer Satisfaction
Department for return authorization: toll free
1-800-572-8822. Collect shipments or shipments without
return authorization cannot be accepted. The product
registration card packaged with our product need not be
returned for the warranty to be effective and for you to
receive warranty service.
Repairs: If your
Johnson Outdoors Gear, Inc.
product
needs service or repair due to normal wear and tear,
animal attack, accident or some other reason that is not
covered under the warranty we will provide the
necessary service for a reasonable charge, plus shipping
and handling. We require that products accepted for any
repair be properly cleaned according to our
recommended care instructions. Please send your
product or component that requires repair (e.g., tent fly),
postage prepaid, along with a description of what needs attention. For
service and repairs, please contact our Customer Satisfaction
Department: toll free 1-800-572-8822
How State Law Relates To This Warranty: This warranty gives you
specific legal rights, and you may have other rights that vary from
state to state.
Our brands are part of the Johnson Outdoors family
of products. Visit all the brands at
johnsonoutdoors.com
We support the "Leave No Trace" Seven
Principles:
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7 . BE COURTEOUS OF OTHER VISITORS
JOHNSON OUTDOORS GEAR INC
WARNING:
KEEP ALL FLAME AND HEAT SOURCES
AWAY FROM THIS TENT!
This tent meets the flammability requirements of CPAI-84. The Fabric may
burn if continuous contact with any flame source. Do NOT operate any
device which burns fuel inside your tent. This could lead to serious injury
or death.
REV 091115
Product specificaties
| Merk: | Eureka |
| Categorie: | Tent |
| Model: | Sunrise EX 4 |
Heb je hulp nodig?
Als je hulp nodig hebt met Eureka Sunrise EX 4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Tent Eureka
2 Juni 2023
15 Mei 2023
13 Mei 2023
12 Mei 2023
10 Mei 2023
7 Mei 2023
6 Mei 2023
4 Mei 2023
3 Mei 2023
2 Mei 2023
Handleiding Tent
- Tent Philips
- Tent IKEA
- Tent Asaklitt
- Tent Babymoov
- Tent Bestway
- Tent Brunner
- Tent Dometic
- Tent Dwt-Zelte
- Tent Fiamma
- Tent Gerjak
- Tent Mx Onda
- Tent Perel
- Tent Rocktrail
- Tent Rollei
- Tent Skandika
- Tent Thule
- Tent Trigano
- Tent Velleman
- Tent Ventura
- Tent Walker
- Tent Woods
- Tent Jamet
- Tent Obelink
- Tent Crivit
- Tent Edges
- Tent Kayoba
- Tent Hamron
- Tent Big Agnes
- Tent Black Diamond
- Tent Camp Master
- Tent Camp Trails
- Tent Carl Denig
- Tent Chinook
- Tent Coleman
- Tent De Waard
- Tent Easy Camp
- Tent High Peak
- Tent Hilleberg
- Tent Jack Wolfskin
- Tent Kelty
- Tent Khyam
- Tent Mountain Hardwear
- Tent Nigor
- Tent Nomad
- Tent Outwell
- Tent OZtrail
- Tent Raclet
- Tent Robens
- Tent Sierra Designs
- Tent Trimm
- Tent Vango
- Tent Vaude
- Tent Vrijbuiter
- Tent Wechsel
- Tent Wilderness Equipment
- Tent Wynnster
- Tent Zempire
- Tent SereneLife
- Tent Aart Kok
- Tent Cabanon
- Tent Holtkamper
- Tent Goldcamp
- Tent Isabella
- Tent Thermex
- Tent Kathmandu
- Tent Sorara
- Tent MSR
- Tent LECO
- Tent TOOLPORT
- Tent Helsport
- Tent Robinhood
- Tent Casaria
- Tent Black Wolf
- Tent Nordisk
- Tent Grand Canyon
- Tent San Hima
- Tent Gazebo Penguin
- Tent Sojag
- Tent Calima
- Tent Yamazen
Nieuwste handleidingen voor Tent
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024