Eureka Solitaire SRS2 Handleiding

Eureka Heater Solitaire SRS2

Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Solitaire SRS2 (4 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
• Smoke entering the room from the firebox when the door is open may be caused by
Insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)
– Increase height of flue.
• Flue Downdraught
– Consult dealer or increase height of flue.
• Creosote Build up in flue
– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.
• Excessive ash build up
Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the
wood which is most convenient for you as long as it is dry. After a period of time you will get to know when to
empty your unit. Always leave 12mm of ash in the bottom of your heater. Bark will give you excessive ash. Try not to
burn it.
If you are burning wood that gives you charcoal, you may find that after running the heater say for 8 hours at
maximum burn rate, the charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If
you are not ready to shutdown for overnight burn when you next fuel the stove, load the stove with only one piece
of wood and lay it across the firebox on top of the charcoal. Open the air control wide open and you will find the
charcoal will burn down with the one piece of wood. Repeat the process until the ash level is significantly reduced.
GPN 207918
REV. D
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
Solitaire SRS2, Onyx, Diamond
& Emerald Mk3 Freestanding
Operation & Installation Instructions
8
Troubleshooting (Continued)
Solitaire SRS2 Freestanding shown
1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship
and/or materials for the following periods from the date of purchase:
(a) the firebox for ten years;
(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and
(c) all other components for twelve months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.
2. This extended warranty does not apply:
(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;
(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in
accordance with the instructions provided by Gason; or
(c) to owners other than the original purchaser.
3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service
centre to arrange for an assessment.
4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:
(a) replace the heater;
(b) repair or replace specific components of the heater; or
(c) provide a full refund.
5. Parts replaced under this warranty are warranted for the balance of their original warranty period.
6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this
warranty must pay all costs associated with:
(a) returning the heater; and
(b) the delivery or collection of any new or repaired heater.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.
Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which
these warranties relate.
These warranties are given by:
A.F. Gason Pty Ltd
Blake Street
Ararat VIC 3322
Please contact us if you have any queries on:
Phone: 03 5352 2151;
or email us via the “Contact Us” section of our website: www.gason.com.au.
Eureka Heating reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.
WARRANTY
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
7
Troubleshooting
!
WARNING
NEVER OPERATE THE HEATER WITH THE DOOR LOOSE AND NOT AIR TIGHT.
OVERFIRING COULD RESULT IN DETRIMENTAL WEAR AND TEAR ON THE
FIREBOX.
Noisy Fan
Turn the power off and remove the three pin plug from the power point. Remove the four screws that hold the front
fan access panel. Remove the panel. Disconnect the wiring loom via the plastic joiner. Unscrew the two nuts which
hold the fan in position and remove the fan. Clean any dust with a dry paint brush and vacuum the fan blades. Clean
around the motor. After completion place two or three drops of sewing machine oil on the shafts at the bearings.
Replace the fan in reverse to the removal.
Fan not working
Check the power connection with another appliance. If the power point is O.K. assume the Fan or the Switch is
defective. Isolate the power as above. Check that the terminals on the loom and the switch are firmly connected. If the
fan then fails to function, remove the fan and switch by firstly removing the knob off the fan switch by pulling it away
from the heater. Undo the holding nut and pull the switch out. Disconnect the wiring from the power lead and remove
the fan and switch. Convey the same to the authorised Eureka Dealer from whom you purchased your unit for service.
Replace in the reverse order.
Air Control Jamming
Remove air control cover plate by removing the four screws which hold it onto the face of the heater. There are two bolts
holding the air slide in place. Undo them and remove the air slide. Wipe any ash or dust that may have accumulated on
the back of the air slide or on the face of the heater. If any burrs have developed on the back of the air slide or on the
face of the heater, rub them off with fine wet and dry sand paper till you have a smooth surface and edges. Replace the
air slide and make sure the washers and spacers are on the bolts when you screw the bolts back into the face of the
heater. Do not apply any type of lubricant to the air slide whatsoever as this will attract dust and make the slide stick.
No Overnight Burn
Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heater. If it is
loose, tighten up the bolts holding the air slide to the face of the heater. Do not overtighten.
Check that the door rope has an even indentation from the sealing strip, which is on the face of the firebox. If it is uneven
and it appears as though air could leak through the seal, adjust the thickness of the door rope to suit. Stretch the rope to
make it thinner where the indentation is the heaviest and bunch up the excess where the indentation is smaller.
Check the four bolts that hold the glass retainer in position. If loose tighten. Do not overtighten.
The door may become loose through the door seal shrinking. To tighten the door, open the door and look at the inside of
the door catch. Undo the nut which is holding the latch plate. Remove the latch plate. Remove one thick washer and the
star washer. Refit the latch plate. The latch plate is concave to provide a lead in edge so that there is smooth connection
between the door latch and the catch. Make sure that the face of the latch that is curved outward is facing towards the
door.
Replace the nut. When closing the door you should now feel firm resistance when the latch comes into contact with the
catch.
Overfiring
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
2
!
WARNING
Read and follow these instructions carefully before installing and
using this appliance.
SAVE THESE INSTRUCTIONS
Paint curing and care
!
WARNING
A flue fire with resulting damage may occur if this appliance is not installed,
operated and maintained as per this booklet.
Never place combustible material such as wood, paper or furniture near the
appliance.
This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,
flammable liquids or any substance containing salts or corrosives.
This appliance must not be installed and operated in an area where kerosene,
petrol, paint thinner or other flammable liquid is used or stored.
The flue system must be inspected and cleaned annually or sooner if required.
Failure to do so could result in an excessive build up of creosote which may
result in a flue fire which may damage the flue or cause damage to your
home.
The surface of the appliance becomes hot during operation. Do not touch the
surface of this appliance. Keep children away from the appliance during
operation. Do not allow anyone to operate this appliance who is not familiar
with the instructions in this booklet.
!
WARNING
Your heater is coated with the best available heat resistant paint. Even though
the paint has been baked after application, it may require further temperature
curing. It may, if you overfire the heater on its first fire, discolour. For your first
two or three firings, never exceed medium air setting and always have the fan on
when above low burn. Do not wipe the heater while the paint is curing. After the
paint has cured the only maintenance required to maintain the heaters finish is to
wipe it with a soft cloth. Do not use any commercial cleaners or solvents on the
paint finish.
We are proud of the presentation of our products. If at any time you need to
freshen up the paint finish, your local dealer has touch up paint available for
purchase. You may even change the colour of your heater if you wish.
If you have any enquires, please contact the dealer from whom you purchased your heater:
PLEASE COMPLETE:
Dealer Name
Dealer Address
Phone
Please attach your original purchase dockets to this booklet for future reference.
Safety Warnings
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
6
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
3
Operating your Eureka (Continued)
Overnight burn
Approximately 30 minutes before turning the heater down to overnight burn it is recommended to load the heater with
fuel for the overnight burn. Leave the air control in the medium to high position. Let the heater run for about thirty
minutes. This will reduce the moisture content in the fuel before shut down. (This will help reduce the creosote formation
in the firebox and flue.) Set the air control to the setting you have found best for your requirements which is normally
about 8mm to the right of full shut down. Turn the fan off and retire. The aim when overnight burning is to have only a
few hot embers left in the bottom of the firebox in the morning. Not huge lumps of wood.
Cleaning your flue
Carefully remove baffle plate and put it to one side. Close the heater door. Obtain a flue brush (Solitaire SRS2 178mm,
Onyx/Diamond/Emerald Mk3 150mm) from your local Eureka Dealer and proceed up onto your roof. Remove the cowl.
Slowly push the flue brush down the chimney until it stops. Pull the brush back out and repeat the process. Each time you
do this you will notice that the brush will go further down the chimney till it reaches the bottom. The soot and creosote
will fall down the chimney and into the firebox. Clean residue from firebox. Replace the baffle plate. Make sure you do
the job well. The cleaner the flue the less chance there will be of the creosote sticking again. After you have replaced the
cowl, inspect the roof flashing for any damage that may have been incurred whilst you were cleaning the flue. Reseal the
seal on the roof with roof and gutter silicone if required.
The fan
It is recommended to run the fan while the heater is operating above low burn on low speed. For extended periods when
the heater is running above medium fire, high or boost is recommended. Boost is recommended for short bursts where a
quick temperature rise is desired in conjunction with a high fire setting. The fan should be cleaned on a regular basis.
(Refer Troubleshooting for fan removal and cleaning.)
!
WARNING
Leaving Door Open
As stated previously in relation to leaving door open 25mm to encourage the fire
to pick up at a faster rate. Your heater has been tested to ensure that no
structural damage can take place if the door is inadvertently left open. However
your paint finish can be damaged if the door is left open for a long period with a
full firebox of fuel with the fan off. Closely supervise your heater while the door is
left open.
Closing the Door
Always ensure that before you close your door there is no wood protruding
beyond the front of the firebox opening. Do not use the door glass as a ’battering
ram’ to push the wood back into the firebox. Damage to the glass by such
impact is not covered by your warranty.
The Door
Installation
!
WARNING
THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS
MANUAL AND THE FLUE MANUFACTURERS SPECIFICATIONS.
WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT
THE INSTALLATION.
If you have any other enquiries, please contact the dealer from whom you
purchased your heater.
THIS APPLIANCE WEIGHS IN EXCESS OF 170 KILOGRAMS. EXTREME CARE
SHOULD BE TAKEN WHEN HANDLING THE APPLIANCE.
Clearances to combustibles & flue requirements
It is recommended that you either use the flue kit that was tested in test report numbers shown below, or an approved
Australian Standard flue kit, (that incorporates a decorative surround which is unperforated for 180 degrees of its
circumference) in conjunction with the original test report.
The Eureka Solitaire SRS2, Onyx, Diamond & Emerald Mk3 have been tested to the Australian Standard 2918:1990 Appendix B.
SOLITAIRE SRS2: Report RF/95/091.
ONYX: Report HCU/98/005 . A
DIAMOND: Report RF/95/097.
EMERALD Mk3: Report HCU/96/116.
The Solitaire SRS2, Onyx, Diamond and Emerald Mk3 Freestanding heaters conform to the Australian Standard in the
following placement of the appliance in relation to combustible surfaces.
Rear Wall
(Solitaire SRS2) 50mm
(Onyx) 50mm
(Diamond) 25mm
(Emerald Mk 3) 125mm
(Solitaire SRS2) 50mm
(Onyx) 50mm
(Diamond) 25mm
(Emerald Mk 3) 125mm
Side Wall
Rear Wall
(Solitaire SRS2) 100mm
(Onyx) 100mm
(Diamond) 100mm
(Emerald Mk3) 150mm
(Solitaire SRS2) 350mm
(Onyx) 330mm
(Diamond) 300mm
(Emerald Mk3) 450mm
Side Wall
Floor Protector
Floor Protector
Installation
SOLITAIRE SRS2:The Solitaire SRS2 conforms to A.S. 2918:1990 when placed in the above position on a minimum
hearth or floor protector of 1170 mm deep x 975mm wide x 7.5mm thickness. The floor protector should extend
400mm in front of the appliance base.
ONYX: The Onyx conforms to when placed in AS/NZS 2918:2018 the above position on a minimum hearth or floor
protector of 1020 mm deep x 1170 mm wide x 4 mm thickness. The floor protector should extend 300mm in front of
the appliance base.
DIAMOND:The Diamond conforms to A.S. 2918:1990 when placed in the above position on a minimum hearth or floor
protector of 1070mm deep x 910mm wide x 7.5mm thickness. The floor protector should extend 350mm in front of the
appliance base.
EMERALD MK3: The Emerald Mk3 conforms to when placed in the above position on a AS/NZS 2918:2018
minimum hearth or floor protector of 1070 mm deep x 900 mm wide x 4.5 mm thickness. The floor protector
should extend 300mm in front of the appliance base.
Hearth Requirements
Operation of the Fan
!
WARNING
If firebox failure is reported and it is found that the firebox has been abused
through improper use of the fan, Eureka reserve the right to disallow any
warranty claims in relation to firebox failure.
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
4
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
5
Fitting the Baffle Plate
After you have completed the installation you firstly have to fit the baffle plate into the heater with the curved lip facing
upright and to the front.
Put the baffle plate back into the heater by putting the right side of the plate through the door opening and then the left.
Holding the plate in two hands under the plate, lift the right hand side up hard against the top and right hand side of the
firebox. Then lift the left hand side past the retaining lugs on the left hand side of the firebox. When the plate is level,
slowly lower it onto the baffle plate retainers. With the baffle plate sitting evenly on the holders, push the baffle plate to
the rear of the firebox so that the rear of the baffle plate is against the back wall and sitting on the rear support.
!
WARNING
WITH THE CURVED LIP FACING UPRIGHT AND TO THE FRONT, ENSURE THE
BAFFLE IS SITTING CORRECTLY. FAILURE TO DO SO WILL CAUSE THE APPLIANCE
TO BE LESS EFFICIENT AND OVERHEAT THE FLUE SYSTEM. IF THE BAFFLE PLATE
IS NOT SUPPORTED AT THE REAR OF THE FIREBOX AND PLACED FIRMLY
AGAINST THE BACK WALL THE BAFFLE MAY BOW DOWNWARDS CAUSING
INEFFICIENT OPERATION.
!
WARNING
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITHOUT READING AND
UNDERSTANDING THESE OPERATING INSTRUCTIONS THOROUGHLY. FAILURE TO
OPERATE THIS APPLIANCE PROPERLY MAY CAUSE UNDUE DAMAGE TO THE
APPLIANCE OR RESULT IN A FLUE FIRE.
Take the firebricks out of the heater. They are to be placed so
that they stand on end against the rear and two side walls of
the firebox. You will notice that the bricks have a bevel on one
end.
Inside the firebox there is aC” shaped angle iron firebrick
retaining bracket. This is designed to sit over the bricks and
hold them in place. This should be placed in the firebox so that
you see a flat face of the angle iron on both sides of the
firebox and at the rear of the firebox.
Holding the “C frame up to the top of the firebox, insert a
whole firebrick, standing it vertically with the bevel edge
pointing down and facing inwards toward the left hand side of
the firebox. Lower the left hand side of the “C frame onto the
firebrick. Repeat with a whole firebrick on the right hand side.
Place firebricks (Solitaire SRS2 - 4 whole firebricks, Onyx &
Diamond - 3 whole firebricks and one half firebrick, Emerald Mk3 - 3 whole firebricks) using the same method against the
back wall of the firebox.
Now place one extra firebrick on either side of the firebox to complete the installation of the firebricks. (i.e. two each side
and remainder on the back wall.)
Push each brick and C” frame firmly against the wall of the firebox and you are ready to light your fire.
Baffle Plate
“C” angle iron bracket
fire bricks
bevelled edge
Operating your Eureka
Your first fire
On installation of your Eureka Heater it is necessary to place a 12mm (approx) layer of sand, soil or ash in the bottom of
the firebox. This is required for the first fire. Thereafter, when cleaning out the firebox, always leave the equivalent amount
of ash in the bottom.
Starting your fire
Place a firelighter or paper in the bottom of the firebox and place a large amount of small kindling on top. Ignite the
paper or the firelighter. Set the air control to high and leave the main door open approximately 25mm. When the kindling
is burning, place about four pieces of small wood on top of the burning kindling. Once the wood is alight, close the main
door. After approximately 20 minutes, turn the air control down to medium and, turn the fan on to low speed.
On the initial fire up you may detect smoke coming from the paint finish and from any oils that may be on the steel on
the outside of the firebox. This is normal. It is suggested to well ventilate your home on the initial fire up. Please refer to
our section ‘Paint curing and cure.
The glass door
Always operate your heater with the door closed and locked. The only time you can leave the door open is on initial
lighting, or when reloading the heater.
Care of your glass
If you are burning good dry wood, you will have very little discolouration of your glass in normal burning cycle. If you aim
for an eight to ten hour overnight burn, you should not get much discolouration. You can control this by adjusting the air
control, moving from the left and slowly creeping the control to the right. After a number of days you will find the right
position to suit your requirements and the fuel that you are using.
Cleaning the glass
Generally the only time you will possibly need to clean your glass is after a long overnight burn. If you find that you have
a wet sticky black film on your glass (creosote), it is better to burn the heater as normal for one load of wood. When the
wood has burnt down to a hot bed of embers, open the door and leave it wide open until the glass cools sufficiently to
be wiped with a damp cloth. This should clean all the white smoky film off the glass. Creosote on the glass is normally a
sign that you have tried to get too long an overnight burn or you have burnt excessively wet or green wood.If the film on
the glass won’t come off with a wet cloth, you can use wet ash from the ash bed as a cleaner or commercial products
such as Crystal Clear, Johnson Foam Clean or Windex.
Normal Operations
When you get up in the morning, open up the air control of the heater to high position to start the embers glowing. Place
three or four pieces of wood on top of the embers and leave the door open 25mm. Once the fuel starts to flame close
the door. As the heater starts to heat up turn the fan on to low, (approx 20 minutes) and begin reducing the air control
towards a lower setting. You will find with the fan on low you will only need to run the heater between low and medium
to maintain the temperature you desire in your home. To obtain the maximum heat dissipation from the heater it is
necessary to run the fan at any time the heater is running above the low position.
For best results it is best to burn 350mm long wood and load your wood straight into the firebox front to rear. This will
give optimum efficiency and recoverable heat, and minimise creosote formation and smoke emissions.
Placement of firebricks in firebox
Installation (Continued)
Read these instructions
Installation Permit
Depending on what your local authority requires, a permit may be required for the installation of your heater. It is your
responsibility to arrange the same.


Product specificaties

Merk: Eureka
Categorie: Heater
Model: Solitaire SRS2

Heb je hulp nodig?

Als je hulp nodig hebt met Eureka Solitaire SRS2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Heater Eureka

Handleiding Heater

Nieuwste handleidingen voor Heater